电液伺服疲劳试验机负荷系统失准调整和校准

叙述了美国MTS公司生产的MTS－810（809）系列电液伺服疲劳试验机负荷系统、DC检测器和量程校准模块的原理、调整方法和力值校准方法。     

Microstructures and fatigue properties of electron beam welds with beam oscillation for heavy section TC4-DT alloy

With the development of the manufacturing technology, electron beam welding（EBW） is capable of producing titanium alloy large parts in aero fields. To increase the applications and improve the properties, EBW with beam oscillation was investigated on TC4-DT alloy with50 mm thickness. We detected the welding samples by X-ray NDT, observed the microstructures of the welds, and tested the fatigue properties of the joints. The results showed that EBW with beam oscillation improved the weld morphology as well as welding quality, and the microstructure homogeneity of the welds and HAZ along the weld penetration were also improved. The fatigue properties of the joints with beam oscillation were more excellent than those of conventional EBW, even equal to those of the base metal under high stresses. The influences of the processing and the microstructure on the properties with beam oscillation were discussed.     

A model-based prognostics method for fatigue crack growth in fuselage panels

This paper proposes a model-based prognostics method that couples the Extended Kalman Filter (EKF) and a new developed linearization method. The proposed prognostics method is developed in the context of fatigue crack propagation in fuselage panels where the model parameters are unknown and the crack propagation is affected by different types of uncertainties. The coupled method is composed of two steps. The first step employs EKF to estimate the unknown model parameters and the current damage state. In the second step, the proposed efficient linearization method is applied to compute analytically the statistical distribution of the damage evolution path in some future time. A numerical case study is implemented to evaluate the performance of the proposed method. The results show that the coupled EKF-linearization method provides satisfactory results: the EKF algorithm well identifies the model parameters, and the linearization method gives comparable prediction results to Monte Carlo (MC) method while leading to very significant computational cost saving. The proposed prognostics method for fatigue crack growth can be used for developing predictive maintenance strategy for an aircraft fleet, in which case, the computational cost saving is significantly meaningful.     

General aspects on structural integrity

This paper seeks to mark the fruitful collaborative research between scholars in the University of Southampton and Beihang University for last 25 years on structural integrity. Their efforts addressed some important issues in structural integrity such as fatigue and fracture behavior,fatigue load spectra, fatigue and fracture lifetimes, reliability-based service period, adhesively bonded composite patch repairs, Plain Woven Fabric(PWF) composites and composite artefacts.New advances in engineering approaches, experimental methods, numerical algorithms and understanding of failure mechanisms relating to structural integrity are highlighted. Probable limits(or drawbacks) are also discussed. This review provides an insight into the general aspects on structural integrity and constitutes a basis for pointers to the further works on structural integrity.     

激光喷丸对7075铝合金搅拌摩擦焊接头的影响

以7075铝合金试样的搅拌摩擦焊接头为对象,利用激光喷丸和常规喷丸工艺对其进行后续处理,通过试验对比分析了激光喷丸工艺对表面粗糙度、显微硬度、接头残余应力、裂纹扩展、疲劳寿命的影响。结果表明,经激光喷丸处理的搅拌摩擦焊接头的表面粗糙度远小于常规喷丸处理的接头表面,而对接头显微硬度的影响差异不大。激光喷丸可改变接头的残余应力分布,是增强搅拌摩擦焊接头抗疲劳性的有效方法,对其他焊接接头及构件的激光喷丸处理具有一定的参考价值。     

考虑耦合损伤的燃气轮机叶片材料高低周复合疲劳寿命研究

燃气轮机叶片在实际工作过程中,受到高低周载荷共同作用而易发生疲劳失效.针对高低周复合疲劳损伤演化和寿命预测比较复杂这一问题,考虑高低周载荷叠加形成的耦合损伤,建立了一种新的高低周复合疲劳寿命预测模型,在此基础之上,引入弱化函数描述某些低幅高周载荷对复合损伤的弱化作用,建立了具有低载强化寿命效应的高低周复合疲劳寿命预测模...     

航空用不锈钢焊接导管的损伤容限研究

基于断裂力学方法开展了1Cr18Ni9Ti导管TIG焊对接结构的损伤容限分析,在测试其母材和TIG焊接头拉伸性能、断裂韧度和疲劳裂纹扩展速率的基础上,分析其失效模式,确定损伤容限ac。研究结果表明:1Cr18Ni9Ti导管TIG焊对接结构在工况振动载荷下,损伤容限ac为0.9mm,导管失效形式为泄露。     

铝锂合金搅拌摩擦焊搭接接头疲劳行为研究

针对Al-Li-S4和2099铝锂合金FSW搭接接头,采用金相组织观察、疲劳性能测试、S-N曲线绘制、断口分析等手段,考察了典型焊接参数下铝锂合金搭接接头的疲劳性能、微观组织,分析了接头断裂形式。     

TA15钛合金电子束焊缝形状对疲劳性能的影响研究

通过选用适当的电子束焊接工艺,可得到4种典型的电子束焊缝形状,分别为钟罩形、漏斗形、楔形和钉形。对不同焊缝形状的电子束焊接接头进行了疲劳性能试验,并利用所建立的层次分析数学模型,综合评价了焊缝形状对疲劳性能的影响。     

Effect of creep feed grinding on surface integrity and fatigue life of Ni3Al based superalloy IC10

Ni₃Al-based superalloy IC10 is widely used in high temperature components of aero-engines because of its superior mechanical properties. In this paper, the creep feed grinding properties of IC10 were investigated experimentally. The effects of grinding parameters on the grinding forces and temperature were examined. Moreover, the influences of surface roughness and hardening on the high-cycle fatigue life of IC10 specimens were studied. To control the creep feed grinding parameters and enhance the fatigue life of IC10 components, the experimental results were summarized to offer a useful reference point. It is concluded that, the grinding depth is the most important factor which influencing the grinding forces and temperature; the surface roughness is the main and unfavorable factor on the fatigue life of IC10, while the surface hardening has a positive influence on the fatigue life; to obtain a better surface quality and improve the fatigue life of IC 10, the recommended grinding parameter domain involves wheel speed ∈ [15, 20] m/s, feed rate ∈ [150, 200] mm/min, and grinding depth ∈ [0.4, 0.5] mm.