基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。     

空冷电机气动噪声的分析与验证

介绍了空冷电机气动噪声的来源、测量方法以及工程上常用的气动噪声控制措施。以某空冷电机为例,采用CFD方法对外风路的稳态流场、瞬态流场以及声场进行了数值分析,将计算结果通过试验进行验证。这对自通风型空冷电机的气动噪声分析具有一定的参考意义。     

基于欠采样的零阶优化算法

非平衡学习吸引了许多研究者的关注。一般情况下,少数类是更值得关注的,并且其误分类代价要远高于多数类。由于非平衡数据分布的非均衡性,标准的分类算法将难以适用。为了解决非平衡数据分类问题,给出了基于欠采样的零阶优化算法。首先,为了降低数据非平衡分布的影响,针对不同非平衡比的数据集给出了不同的两种采样策略。然后,采用了一种引入间隔均值项的支持向量机(Support vector machine,SVM)优化模型进行分类,并使用带有方差减小的零阶随机梯度下降算法进行求解,提高了算法的精度。在非平衡数据上进行了对比实验,实验证明提出的方法有效提高了非平衡数据的分类效果。     

Laminar flow control research at TsAGI: Past and present

This paper presents a brief review of activities in laminar flow control being performed at the Central Aerohydrodynamic Institute named after Prof. N.E. Zhukovsky (TsAGI). These efforts are focused on the improvement of the existing laminar flow control methods and on the development of new ones. The investigations have demonstrated the effectiveness of aircraft surface laminarization applications with the aim of friction drag reduction. The opportunity of considerable delaying of laminar-turbulent transition due to special wing profile geometry and using boundary layer suction and surface cooling has been verified at sub- and supersonic speeds through various wind tunnel testing at TsAGI and during flying laboratory experiments at the Flight Research Institute (LII). The investigations on using hybrid laminar flow control systems for friction drag reduction were also carried out. New techniques of laminar flow control were proposed, in particular, the method of local heating of the wing leading edge, boundary layer laminarization by means of receptivity control, and electrohydrodynamic methods of boundary layer stability control.     

一种鲁棒的概率核主成分分析模型

大数据时代面临的数据维数越来越高,对数据降维处理越发显得重要。经典的主成分分析模型已被证明是一种有效的数据降维方法。但它在处理非线性、存在噪声和异常点的数据时存在效果较差的问题。对此,文章提出了一种鲁棒概率核主成分分析模型。该模型将核方法与基于高斯隐变量模型的极大似然框架相结合,用多元 t分布作为先验分布,以同时解决主成分分析在这 3个方面的弊端。提出混合鲁棒概率核主成分分析模型,使其可直接用于对混合的非线性数据进行降维和聚类分析。在不同数据集上进行的实验结果表明,与标准的混合概率核主成分分析模型相比,文中模型在数据聚类方面有更高的准确率。     

后掠翼三维鼓包串激波控制参数的影响

针对跨声速后掠翼,三维鼓包串作为一种有效的减阻方式具有结构简单、高效及鲁棒性好等优点.利用全局优化算法探索了鼓包设计参数空间的整体特性,并对鼓包长度、三维鼓包展向设计参数对鼓包减阻效果的影响进行了研究,发现鼓包顶点位置和高度对阻力系数最敏感,三维鼓包的展向设计参数则对阻力系数不敏感,而鼓包长度和鼓包相对展长越长越有利于减阻.在此基础上开展了小后掠角自然层流机翼加3种不同类型鼓包串的优化研究,通过优化结果发现,增加优化后的三维鼓包串,可将小后掠角自然层流机翼阻力发散马赫数向后推移,并且鼓包平均长度和控制区越大,效果越好.三维鼓包串具有良好的局部控制特性,可用于局部较强激波的抑制.三维鼓包串对常规后掠翼波阻具有良好的控制效果,同时能够抑制激波诱导的机翼后缘气流分离.      

共轴式直升机桨毂阻力特性与减阻试验

共轴式直升机桨毂阻力占全机废阻的50%以上,因此有必要对桨毂阻力特性和减阻设计进行研究。 通过对某共轴式直升机桨毂模型、减阻方案及减阻方案加装涡流发生器进行风洞试验,研究轴式直升机桨毂的 阻力特性,验证减阻方案及减阻方案加装涡流发生器的减阻效果。结果表明:桨毂支臂方位角、转速和攻角变 化对桨毂及其减阻方案的阻力影响很小;上下桨毂整流罩与中间轴整流罩之间的缝隙对阻力影响比较大;减阻 方案可以降低约33%的桨毂阻力,而加装涡流发生器的减阻效果并不明显。     

Drag derived altitude aided navigation method

The navigation problem of the lifting reentry vehicles has attracted much research interest in the past decade.This paper researches the navigation in the blackout zone during the reentry phase of the aircraft,when the communication signals are attenuated and even interrupted by the blackout zone.However,when calculating altitude,a pure classic inertial navigation algorithm appears imprecise and divergent.In order to obtain a more precise aircraft altitude,this paper applies an integrated navigation method based on inertial navigation algorithms,which uses drag derived altitude to aid the inertial navigation during the blackout zone.This method can overcome the shortcomings of the inertial navigation system and improve the navigation accuracy.To further improve the navigation accuracy,the applicable condition and the main error factors,such as the atmospheric coefficient error and drag coefficient error are analyzed in detail.Then the damping circuit design of the navigation control system and the damping coefficients determination is introduced.The feasibility of the method is verified by the typical reentry trajectory simulation,and the influence of the iterative times on the accuracy is analyzed.Simulation results show that iterative three times achieves the best effect.     

细长杆降低超声速客机气动噪声的数值分析

在超声速客机机头加装适当的细长杆可以降低飞行噪声。本文借助基于AUSM+格式的准三维数值模拟手段对7组13种细长杆方案做了分析比较,总结出了近场气体参数与远场气体参数之间的关系的规律。文章还从气体动力学理论和激波理论出发,对数值模拟结果作了解释,并揭示了细长杆降噪效果与细长杆外形的内在联系,以及近场、远场两者关系的经验公式。文章从各种方案中选取了降噪效果较好的细长杆方案做三维流场分析,并通过流固耦合计算对其结构强度做了校核,验证了方案的可行性。     

Shock protection of penetrator-based instrumentation via a sublimation approach

It is often necessary for space-borne instrumentation to cope with substantial levels of shock acceleration both in the initial launch phase, as well as during entry, descent and landing in the case of planetary exploration. Current plans for a new generation of penetrator-based space missions will subject the associated on-board instrumentation to far greater levels of shock, and ways must therefore be found to either ruggedize or else protect any sensitive components during the impact phase. In this paper, we present an innovative method of shock protection that is suited for use in a number of planetary environments, based upon the temporary encapsulation of said components within a waxy solid which may then be sublimated to return the instrument back to its normal operation. We have tested this method experimentally using micromachined silicon suspensions under applied shock loads of up to 15,000g, and found that these were able to survive without incurring damage. Furthermore, quality factor measurements undertaken on these suspensions indicate that their mechanical performance remains unaffected by the encapsulation and subsequent sublimation process.