TIG 焊接 Ti - 6Al - 4V 钛合金薄板工艺与组织分析

为探索更合理的焊接工艺方法,作者采用TTG焊接1．2mm的钛合金薄板,分别采用焊接电流为65A、60A、50A和55A焊接四组试样,并对焊件进午亍外观分析、无损检测、拉伸性能测试、金相扫描等检测,通过对比,采用焊接电流为65A,焊接速度为173mm／min,正反面Ar气的流量为10L／min,钨极直径为Ф1．6mm,焊丝直径书1．6mm的工艺参数来焊接1．2mm的TC4钛合金较为合理。     

钛合金TB6铣削加工硬化实验

研究了使用涂层硬质合金刀具对钛合金TB6进行端铣加工时,铣削参数以及刀具后刀面磨损量对加工硬化（表面硬化率、硬化层深度以及硬化层硬度分布）的影响,以弄清TB6铣削硬化现象及机理.结果表明,在实验参数范围内,刀具无磨损的情况下,硬化率基本保持在107%~112%范围内,硬化层深度范围为18~36 μm;铣削速度增加时,加工硬化程度会有较为明显的降低现象,而进给量与切深对加工硬化的影响并不明显;刀具磨损对加工硬化的影响较为显著,后刀面磨损量低于0.2 mm时,硬化层深度随着磨损增加从30 μm增加至55 μm,而后刀面磨损量为0.35 mm时,硬化层深度达到了130 μm.刀具磨损后在加工表面下较浅位置出现软化区域,而且随着磨损量的增加,软化越来越明显.      

厚度和环境对复合涂层导电性能的影响

为了给数字化刻铣曲面频率选择表面(FSS)结构的制作和加工提供参考和依据,对比研究了含片状银粉颗粒的聚氨酯基和环氧树脂基2种复合导电涂层的基本性能,并通过环境加速试验,重点研究了温度、湿度以及腐蚀气氛对2种导电涂层的界面强度、微观结构和导电性能的影响.通过电桥法测量涂层表面电阻的变化,并通过扫描电境观察环境试验前后,涂层表面和剖面的微观结构和形貌变化.试验结果表明:聚氨酯基涂层的综合性能优于环氧树脂基涂层;在实验所涉及的参数变化范围内,环境因素对2种涂层与基体的界面结合影响不大,但对其导电性能的影响比较明显.环境因素对导电性能的削弱作用,源于相应过程中导电涂层的微观结构损伤.     

浇注温度对1种新型铸造镍基高温合金组织和拉伸性能的影响

为分析浇注温度与合金的组织结构和力学性能之间的变化关系,通过改变浇注温度获得不同枝晶组织试样,采用金相显微镜和扫描电镜来观察和分析合金的组织结构,结合拉伸性能测试研究了合金的组织结构对拉伸性能的影响。结果表明：降低浇注温度使γ＇相和碳化物得到细化;降低浇注温度提高了合金的拉伸强度,并改善了塑性。     

基于细观位错机理的单晶合金高温力学性能模拟

利用基于细观位错运动的蠕变筏化模型对镍基单晶合金CMSX-4在1223K下的拉伸、蠕变、循环、蠕变疲劳交互及各向异性进行模拟,结果表明:拉伸过程中应变率较高时应力略微下降的现象;蠕变条件下应力越大则蠕变第1阶段越明显,而蠕变稳定阶段越短的趋势;蠕变疲劳交互作用下的应力松弛和应变增大;以及单晶3个典型晶体取向的循环应变硬化特征。通过与试验结果对比,验证了此模型在较高温度下对单晶合金性能的综合模拟能力。     

7050铝合金搅拌摩擦焊接头组织特征研究

针对7050铝合金搅拌摩擦焊接头,给出各组织特征区的定义,并对各特征区的组织状态、晶粒大小、沉淀强化相分布等进行深入的分析。为同材质的铝合金搅拌摩擦焊接头的综合性能评估提供更好的依据。     

微量Y对Al-Mg-Si系合金组织性能的影响

在熔炼过程中以铝钇中间合金形式加入稀土Y元素,研究了0～0.45%范围内不同Y加入量对Al-Mg-Si系铝合金铸态组织、导电性能及高温蠕变抗力的影响。结果表明:经过适量稀土Y微处理后的合金材料具有细小均匀的铸态组织,平均晶粒尺寸维持在50μm左右,材料的导电能力得到一定程度的改善,最佳电导率比原来增加4%,实验材料的热稳定性显著增强,高温下的硬度、抗拉强度分别比原来提高30%和25%。     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

Investigation of vertical profile of rain microstructure at Ahmedabad in Indian tropical region

The microstructure of rain has been studied with observations using a vertical looking Micro Rain Radar (MRR) at Ahmedabad (23.06°N, 72.62°E), a tropical location in the Indian region. The rain height, derived from the bright band signature of melting layer of radar reflectivity profile, is found to be variable between the heights 4600 m and 5200 m. The change in the nature of rain, classified on the basis of radar reflectivity, is also observed through the MRR. It has been found that there are three types of rain, namely, convective, mixed and stratiform rain, prevailing with different vertical rain microstructures, such as, Drop Size Distribution (DSD), mean drop size, rain rate, liquid water content and average fall speed of the drops at different heights. It is observed that the vertical DSD profile is more inhomogeneous for mixed and stratiform type rain than for convective type rain. It is also found that the large number of drops of size <0.5 mm is present in convective rain whereas in stratiform rain, drops concentration is appreciable up to 1 mm. A comparison of measurements taken by ground based Disdrometer and that from the 200 m level obtained from MRR shows good agreement for rain rate and DSD at smaller rain rate values. The results may be useful for understanding rain structures over this region.     

微量B和C对TiAl合金铸锭缩孔缩松的影响

采用真空感应磁悬浮熔炼合金、重力浇注入室温石墨模具的方法,分别制备了Ti-47Al-2Cr-2Nb,Ti-47Al-2Cr-2Nb-0.8B和Ti-47Al-2Cr-2Nb-0.1C 3种名义成分的铸锭.对铸锭进行成分分析并利用体视显微镜和扫描电子显微镜对铸锭的铸造收缩缺陷和组织进行分析.结果表明:Ti-47Al-2Cr-2Nb合金铸锭有很强的柱状晶生长趋势,在轴线附近区域形成分散的缩松;加入0.8%B(原子分数)后,铸锭的组织得到细化,并削弱了柱状晶生长趋势,收缩缺陷分布集中以大缩孔方式存在,显微缩松的密度和尺寸均降低.添加0.1%C(原子分数)后,铸锭的组织和缩孔缩松与Ti-47Al-2Cr-2Nb比均无明显变化.