航空压气机叶片激光测量仪处理系统软件设计

从航空发动机压气机叶片型面检测的传统方法及特点出发,简单介绍了激光测量仪总体系统,重点阐述了处理系统软件的设计,并将其应用于实践中。     

卫星天线热真空环境应变测试并行试验的可行性研究

文章论述了在KM4空间环境模拟器中同时进行两个卫星天线子阵的热真空环境应变测试试验的可行性.利用该可行性研究指导试验,试验结果满足两个子阵的试验要求,证明了这种并行试验的方法可行有效.该项试验的成功进行,为空间环境试验方法开拓了一个新的思路,可以用来进行类似的并行试验.     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

面向航空试验的分布式仿真与测控系统研究

介绍了分布式仿真与测控环境的基本特点与发展过程,着重分析了当前广泛采用的分布交互仿真(DIS)标准和高层体系结构(HLA)标准,最后,结合航空领域的需求,提出应用示范系统,并指出该项技术在航空业的应用前景。     

数控线切割三维直纹面直接刀补算法的研究

分析了四轴数控线切割机床所能加工的三维直纹面类型,以二维C型刀补为基础,根据各类型形状的特点采用了不同的刀补处理方法,分析了用二维刀补原则解决三维直纹面刀补的可行性,提出了一种不需将加工轨迹线形化的三维直纹面的直接刀补算法,指出了降低复杂直纹面刀补误差的措施。     

水洞实验图像的一种测量与处理方法

在水洞实验中,由于光线在空气、水和观察窗面板中发生折射,准确实验图像的获取一直是一个难题。本文在大量水洞实验图象测量经验积累的基础上,以水洞模型超空化实验中的超空泡外形测量为例,提出了一种基于计算机图形学的水洞实验图像测量与处理的三步法。该方法不仅可对水洞实验中所拍摄的图像进行修正,消除因不同介质引起的折射误差,而且把图像数据化,可利用计算机对图形自动进行定量处理。经多次应用表明,图像测量与处理的三步法应用方便,具有较高的精度,取得了很好的应用效果。     

翼型低速动态测压实验的初步分析

简述了翼型低速动态实验研究的测试设备和实验方法。给出了NACA。。12翼型动态测压的实验结果，初步分析了影响翼型动态气动特性的因素。将所得实验结果与国外实验结果及理论计算结果进行了对比与分析，实验结果与资料值有较好的一致性。     

民机低速风洞测力试验技术研究

民机低速风洞测力试验技术是中国航空工业空气动力研究院低速所新研制的一项试验技术,为了达到国际先进测量水平,该项技术先后成功研制了专用的应变天平,改进了模型支撑和稳风速控制系统,用CRJ民机模型进行了风洞试验验证。试验结果表明:FL 8风洞的测量精度已经达到了国际先进水平。     

Cutting force model and damage formation mechanism in milling of 70wt% Si/Al composite

High-mass fraction silicon aluminium composite(Si/Al composite) has unique properties of high specific strength, low thermal expansion coefficient, excellent wear resistance and weldability. It has attracted many applications in terms of radar communication, aerospace and automobile industry. However, rapid tool wear resulted from high cutting force and hard abrasion, and damaged machined surfaces are the main problem in machining Si/Al composite. This work aims to reveal the mechanisms of milli...     

Influence of deformation zone length on bending radius of SS304 tubes with small diameters manufactured via free bending-based active motion

In three and six-axis free-bending equipment, the deformation zone length(A) is a fixed mechanical structure parameter modified when the relevant structure is redesigned and manufactured. In this study, a six degree of freedom(6-DOF) parallel mechanism was used as the control mechanism of the bending die, and a new method of changing the deformation zone length(A)was proposed. Firstly, an idealized geometric model of free bending-based active motion was established. Then, the influence of the de...