Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

页轮干式磨削Ti6Al4V合金

进行了Ti6A14V合金锆刚玉页轮和碳化硅页轮的磨削性能试验研究，分析了磨削用量对磨削力、磨削温度和磨削表面完整性的影响。磨削力通过KISTLER9265B测力仪测定，磨削表面温度由NIUSB-621X信号采集系统测得，磨削表面形貌和金相组织由HiroxKH-7700型体视显微仪和Quanta200型扫描电镜（SEM）观察，表面粗糙度由Mahr Perthometer M1粗糙度仪测得，表层显微硬度通过HVS—1000硬度计测定。研究结果表明：页轮磨削钛合金工件表面没有发生烧伤现象，磨削热影响区厚度小于50μm，锆刚玉页轮比碳化硅页轮更适合干式磨削钛合金。     

单层超硬磨料砂轮制造技术新发展

概述了国外单层高温钎焊超硬磨料砂轮的工艺优势及主要研究成果，这种新型超硬磨料砂轮以其卓越的磨削性能已在国内外磨削界引起了轰动，它在今后逐步替代传统砂轮应是一种无法抗拒的必然趋势。鉴于它极其广阔的应用前景，国内在推广应用超硬磨料砂轮时也必将大力引进开发此种单层钎焊砂轮。为使国内开发钎焊砂轮有一个更高的起点，作者提出了关于开展这一领域研究的若干构想和实施方案     

单层钎焊砂盘磨粒分布有序性研究

对亲型非砂轮磨削工具－－单层钎焊砂盘的硬质合金磨粒在基体上的分布进行了初步研究，砂盘作为一种手握粗磨削工具，降低磨削力是最重要的，文中借鉴砂带及单层高温钎焊超硬磨料砂轮的一些研究，提出了砂盘的磨粒在基体上有序性分布的概念，将此概念应用于砂盘钎焊制造工艺上，在相同的制造工艺和磨洵深度条件下，对得到的磨粒有序性及无序性分布的砂盘进行了磨削对比实验。结果表明，砂盘磨粒的有序性分布能显著降低其磨削力。此概     

缓磨时工件烧伤过程的计算机仿真研究

在关于缓磨时的磨削热、接触弧区换热过程以及工件表层非稳态温度场的深入研究的基础上构造了一个可用于计算工件表层温度场畸变历程的数学模型，并据此完成了缓磨时工件烧伤过程的计算机仿真研究。仿真结果与缓磨时的实际烧伤过程吻合良好。本文率先阐明了缓磨烧伤的热机理，并证实了缓磨烧伤是一典型的渐变过程，它有明显的前兆特征，因而是可以被预报和控制的。此项创造性工作可以被看作是对磨削基础理论的一项重要贡献。     

TC4钛合金材料采用金刚石砂轮磨削时的工艺参数优化

钛合金材料在航空器和发动机中的应用极为广泛,涡扇发动机中低压压气机静子叶片基本由钛合金材料制成,由于钛合金的磨削性能较差,对选用金刚石砂轮进行钛合金材料磨削时的主要工艺影响因素（如进给速度、磨抛深度等）进行了试验分析,优选出更适用于金刚石砂轮磨削钛合金的工艺参数,该参数不仅能够用于自研的双面仿形抛修设备,还可以对其他型号磨床磨削钛合金材料时的工艺参数选择提供指导。     

薄壁微三维结构件超精密研抛技术研究

针对影响薄壁微结构件超精密研抛的工艺因素,即单次进给量、研磨轨迹、研磨膏选择和去除量精确控制,通过大量的研抛加工试验,进行研抛工艺研究,得到能实现稳定和理想加工结果的研抛工艺,很好的满足零件性能要求。     

非圆等距型面轮廓X-C轴联动高速磨削试验北大核心CSCD

针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。     

断续缓磨射流冲击强化磨削弧区换热的实验研究

通过深切缓磨时磨削烧伤机理的分析,提出高压射流冲击强化磨削弧区换热新构想,并通过断续缓磨射流侧向冲击弧区的磨削实验显示其换热效果．