基于一种新的均匀化实施方法的FRP刚度预测

基于一种新的渐近均匀化(AH)实施方法,预测并讨论了单向纤维增强复合材料(FRP)的宏观等效弹性性能及纤维排列方式对等效力学性能的影响。该方法方便地将有限元分析(FEA)软件作为一个工具箱使用,只需在单胞上施加简单位移周期边界条件开展静力学分析,即可经过简单计算得到等效弹性常数,相比传统均匀化实施方法显著降低了实施难度并简化了计算过程。通过对比不同数值方法的结果验证了该方法的有效性和精确性。数值结果表明:六边形排列下单向纤维增强复合材料呈现横观各向同性,而正方形排列下则呈现宏观正交各向异性,经过刚度平均化过程可得到横观各向异性材料性质,纤维体积含量对两种排列方式下材料等效弹性模量影响显著但有所差别。     

新型结构粘接材料对航空有机玻璃性能的影响

选用新型结构粘接材料中低温固化环氧结构胶膜J-351和改性丙烯酸酯液体胶胶黏剂SY-50s,表征胶黏剂对有机玻璃的粘接性能以及应力-溶剂银纹性能,并研究胶黏剂对有机玻璃力学性能的影响。结果表明:两种胶黏剂对有机玻璃具有良好的粘接性能,J-351抗应力溶剂银纹性能优于SY-50s;有机玻璃表面施胶后力学性能下降,与定向有机玻璃相比,浇注有机玻璃力学性能下降更为明显。通过对拉伸试样断口形貌分析发现,拉伸试样带有胶黏剂的一侧首先发生破坏。因SY-50s与有机玻璃界面结合紧密,导致带有SY-50s胶黏剂的有机玻璃力学性能下降程度较大;而J-351环氧胶膜与有机玻璃界面清晰,对有机玻璃力学性能影响相对较小。因胶黏剂对有机玻璃性能的影响,导致采用SY-50s胶黏剂粘接的试样边缘连接强度低于J-351胶黏剂粘接的试样,新型结构粘接材料J-351环氧胶膜在有机玻璃粘接中应用性能良好。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

Mg-Sc-Y三元合金的微观组织和力学性能

稀土元素作为重要的镁合金强化相元素,其多元添加产生的影响并未得到充分研究。在Mg-Sc二元系的基础上将Y作为第三元加入,制备了Mg-5Sc二元合金及Mg-5Sc-0.5Y,Mg-5Sc-1Y,Mg-5Sc-2Y,Mg-5Sc-3Y,Mg-5Sc-3.5Y(质量分数,%)5种三元合金,并通过光学显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射(XRD)及室温拉伸等试验,研究了Y元素的加入对Mg-Sc二元合金微观组织和力学性能的影响。结果表明:Y元素在合金中的主要存在形式为固溶态,富集于晶界处。随着Y元素含量的提升,合金晶粒度显著减小,屈服强度和硬度大幅提升,Mg-5Sc-3.5Y的屈服强度相比Mg-5Sc提升了约50%。该强度的提升主要是由细晶强化和固溶强化引起的。     

阻燃钛合金Ti40的热物理性能及力学性能

作为一种功能性钛合金,Ti40阻燃钛合金的热物理性能数据首次被报道。采用真空自耗电弧熔炼技术制备的Ti40合金铸锭成分均匀,利用热挤压开坯+包套保护锻造方法制备的板坯组织均匀。性能测试结果表明:Ti40合金的室温抗拉强度为950 MPa级,且在500℃下具有良好的热暴露性能、高温蠕变性能和高温持久性能。在室温到600℃范围内,合金的杨氏模量和剪切模量随着温度的升高呈线性下降,泊松比随着温度升高而缓慢增加;线性热膨胀曲线随着温度升高呈抛物线增加,平均线膨胀系数随着温度的升高呈线性增加。     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

超高速撞击下PTFE/Al含能材料薄板的载荷特性分析

不同于传统惰性材料的空间碎片防护结构,含能材料防护结构在超高速撞击下的冲击起爆特性是其防护能力得以提高的根本原因。PTFE/Al含能材料防护结构的冲击起爆特性改变了弹丸强冲击载荷下的破碎机制,弹丸内部的冲击压力对于分析含能材料在超高速撞击下的防护机理具有重要意义。对超高速撞击试验中回收的PTFE/Al防护结构后板进行损伤特性分析,获得了对应速度条件下弹丸的破碎特性。基于一维冲击波理论,分析PTFE/Al靶板在超高速撞击条件下的冲击响应过程,结合考虑化学反应效率的热化学反应模型,获得了弹丸在碰撞与爆炸联合作用下的载荷特性,通过与试验结果对比验证,获得该材料完全反应的临界撞击速度约为1800 m/s,弹丸的临界破碎速度为2875 m/s,小于铝防护结构中对应的临界破碎速度。给出了弹丸在PTFE/Al、铝两种防护结构中产生相同冲击压力时对应的临界速度,分别为弹道段的800 m/s和破碎段的3580 m/s。     

数字全息测量超高速撞击碎片云实验研究

在中国空气动力研究与发展中心(CARDC)超高速碰撞中心(HIRC)7.6 mm超高速碰撞设备的基础上，搭建纳秒级脉冲激光数字全息系统。提出滤波片和衰减片组合布置，减弱超高速碰撞等离子体自发光、提高信噪比的方法。实验获得了2.25 mm铝球弹丸以4.0 km/s的速度撞击0.5 mm厚铝板形成碎片云的全息图。采用小波变换算法对碎片云全息图进行重建，得到超高速撞击碎片云的三维结构和碎片大小。碎片云的轮廓呈椭球型，分为碎片云的前端、核心和外壳，碎片主要分布在弹丸破碎形成的碎片云核心，存在大碎片，且分布较集中，对后板的损伤也严重     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。