Corrosion Inhibition of SiC_p/5A06 Aluminum Metal Matrix Composite by Cerium Conversion Treatment

This article studies the effects of the CeCl₃ concentrations in conversion solutions with and without addition of NaCl, pH-values of conversion solution, drying temperature, time and temperature of immersion on the Ce-conversion coatings for corrosion protection of the SiC_p/5A06 Al-MMC and 5A06 Al-alloy in the 3.5% NaCl aqueous solution at room temperature. Potentiodynamic polarization tests reveal that the Ce-conversion treatment could markedly improve the pitting corrosion resistance of the composite and the matrix alloy in chloride containing environment. The best corrosion resistance effects are obtained for the samples treatment in 1‰ CeCl₃·7H₂O/ 3.5% NaCl solution at 45 °C for 60 min, followed by drying at 100 °C for 30 min. Examinations by means of scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) indicate that this behavior is due to the precipitation of Ce-oxides/hydroxides on the cathodic intermetallics and the Al-oxide film on the rest of the metal matrix.     

6156-T4铝合金焊接加筋薄壁结构剩余强度评估的CTOD方法

为保证飞机设计满足损伤容限性能要求,有必要对其进行剩余强度评估。针对6156-T4铝合金焊接连接薄壁结构进行了R曲线和剩余强度试验,判断了裂纹扩展经过筋条时的裂纹扩展路径,测量了母板和筋条两个方向的裂纹扩展速率,并采用不同的断裂准则和分析方法对单及双跨度多个初始裂纹长度焊接加筋薄板的剩余强度进行了预测。结果表明:裂纹扩展在经过筋条时,同时沿着母板和筋条继续扩展,筋条上的裂纹扩展方向垂直于母板且两个方向的裂纹扩展速率基本相同;采用净截面屈服准则进行剩余强度预测时会低估这种韧性较好的焊接连接薄壁结构的剩余强度;基于SINTAP-FITNET评价体系,以裂纹尖端张开位移(CTOD-δ5)作为裂纹尖端弹塑性表征参量进行剩余强度预测时,预测结果比采用K曲线预测方法精度高。     

2. 5D 衍生结构SiO2 f / SiO2 复合材料的经向力学性能

以几种不同的2.5D衍生结构织物为增强体,制备了法向增强、经向增强及经法向增强2.5D Si O2f/Si O2复合材料,比较了上述材料与现有2.5D Si O2f/Si O2复合材料的经向力学性能,并研究了经法向增强2.5D结构复合材料中增强纱比例、纤维体积分数与材料性能之间的关系,对织物结构进行了优化。结果表明,经法向增强2.5D Si O2f/Si O2复合材料的经向力学性能较现有2.5D复合材料有显著提高,该材料在较低密度下(1.6 g/cm3),经向拉伸强度与现有材料(1.65 g/cm3)持平,且经向压缩强度接近现有材料的4.3倍。     

材料特性对热障涂层合理压入深度的影响

基于有限元计算方法和量纲分析原理提出了热障涂层合理压入深度的确定方法,并研究了涂层及基体材料特性对合理压入深度的影响.首先,根据量纲分析原理提出了合理压入深度的无量纲表达式;其次基于锥形压头识别理想弹塑性材料的材料特性的方法,提出合理压入深度的确定方法;最后研究了各无量纲因素对合理压入深度的影响.研究发现基体的弹性模量对合理压入深度的影响最大,粘结层材料特性的影响较大,热氧化生成层的材料特性及基体的屈服极限对合理压入深度的影响不大.     

Balloon altitude studies of southern hemisphere hard X-ray sources by the Imperial College-University of Tasmania-INPE collaboration

Hard X-ray balloon altitude measurements with a 1600 cm² phoswich array are described. Data from observations on Sco X-1, GX1+4, GX5−1, Nova Oph. 1977, SMC X-1, SS433, IC 4329A and MR 2251-178 are presented. The role of Comptonisation in X-ray production for Sco X-1 and GX1+4 is discussed.     

平板上钝缘舵在超声速绕流中的三维分离特性研究

对于平板上的直立钝缘舵在M_∞=1.79、2.04和2.50的条件下,研究了该平板干扰区中的三维分离特性。着重讨论了钝缘直径、舵面迎角和来流马赫数对主分离线位置和形状的影响。分析了该类三维分离在性态上更强地依赖于无粘流动特性。此外,还对分离区内的二次分离发展过程和形态进行了初步讨论。     

Ground experiments of Chang’e-5 lunar regolith penetrating radar

The Lunar Regolith Penetrating Radar (LRPR) is an Ultra-Wideband (UWB) array-based Ground penetrating radar (GPR) onboard the lander of Chang’e-5 (CE-5) mission. The primary scientific objectives of the LRPR are to probe the thickness and structure of lunar regolith of the landing site, and support the drilling and sampling process. In order to evaluate the performance of the LRPR, a series of ground experiments are performed using the LRPR prototype mounted on a CE-5 lander model. The performance of the LRPR is evaluated by comparing the experimental data with the simulated data. Data processing and imaging method are verified, and the interferences from the lander and other aspects are analyzed. The results of the ground experiments and simulation demonstrate that the LRPR is able to meet the design requirement of 2-m detection depth. They also indicate that the upper and lower interfaces of the stratified structure in the lunar regolith can be well distinguished by the LRPR when the dielectric constant difference is greater than 0.3, and the imaging effect of the location under the dense antennas is better than that of other positions. However, the identification capability of the LRPR to the independent blocky objects is relatively poor mainly due to the clutters caused by the lander, the sparsity of the antenna elements compared to the size of the basalt block, the limited aperture of the antenna array, and the tail of the transmitted waveform.     

失效概率矩独立全局灵敏度分析的高效算法

失效概率矩独立全局灵敏度分析对指导可靠性优化至关重要，本文从乘法降维及Edgeworth级数展开的角度提出一种失效概率矩独立全局灵敏度指标分析的高效算法。所提算法通过Edgeworth级数展开将失效概率矩独立全局灵敏度指标的求解转化为输出无条件及条件前四阶整数矩的求解。对于输出的无条件及条件四阶矩的计算，基于乘法降维的思想，本文推导了重复利用计算输出的无条件矩的输入输出样本来计算条件矩以及外层关于输入变量一维积分的计算公式，使得仅需重复利用输出无条件前四阶矩求解产生的积分网格内的数据即可同时求得输出的前四阶条件矩以及外层关于输入变量的一维积分。所提算法大大提高了失效概率矩独立全局灵敏度的分析效率。航空发动机涡轮盘以及汽车前轴的分析结果验证了所提算法的高效性及准确性。     

通信导航融合定位技术发展综述

详细分析了蓝牙、Wi-Fi、超宽带、移动通信网络等多种无线网络通信导航融合定位技术的发展现状,并阐述了其面临的挑战,提出了多网融合方法可以提升室内无缝高精度位置服务的可靠性。利用5G移动通信网络,与北斗/GNSS卫星导航系统结合,可以实现相互增强。最后,从天地一体定位导航与授时体系和仿生通信定位导航两方面介绍了通信导航融合定位技术的未来发展趋势。     

2.5维机织复合材料细观几何模型及刚度预测方法研究进展

本文从2.5维机织复合材料细观几何结构出发,讨论了织造及成型工艺对材料实际细观几何结构的影响,并分析了不同纱线截面及路径假设所建立代表性体积胞的优缺点。对考虑工艺因素的代表性体积胞是否具有统一性和体素单元法建模的合理性做出对比分析。在代表性体积胞的基础上,重点讨论了2.5维机织复合材料刚度的数值预测方法,并将其与刚度的理论预测方法作了简单对比。基于刚度的数值预测方法,分析了各种机织参数对刚度系数的影响,并且对比了不同代表性体积胞模型的应力场。此外,还讨论了2.5维机织复合材料叶片的建模分析技术与刚度设计方法。最后,指出了当前2.5维机织复合材料细观建模及刚度预测方法存在的问题与不足,并且对其力学性能研究的发展趋势进行了展望。