超声速条件下多体干扰与分离试验研究

采用根据国外公开文献设计的类CAV模型,在0．6m×0．6m 跨/超声速风洞中开展了多体干扰与分离网格测力试验研究,初步获得了典型多体飞行器分离过程中的气动特性变化规律。试验结果表明,载荷模型气动特性受分离位置变化影响非常明显。载荷模型沿轴向分离时,气动力（矩）逐步接近自由流中气动力（矩）值,载荷模型法向位置改变会引发其气动力（矩）值发生更为剧烈的变化。引发这种现象的原因有两个：一是尾迹和头激波的发展改变了不同轴向位置处载荷模型的表面流态,从而影响了其气动特性;二是母机模型底部流动具有明显的非对称膨胀特征,不同法向位置处流速大小和方向差异明显,导致载荷模型气动特性随法向位置变化更为剧烈。     

Flutter analysis of an airfoil with nonlinear damping using equivalent linearization

The equivalent linearization method （ELM） is modified to investigate the nonlinear flut- ter system of an airfoil with a cubic damping. After obtaining the linearization quantity of the cubic nonlinearity by the ELM, an equivalent system can be deduced and then investigated by linear flut- ter analysis methods. Different from the routine procedures of the ELM, the frequency rather than the amplitude of limit cycle oscillation （LCO） is chosen as an active increment to produce bifurca- tion charts. Numerical examples show that this modification makes the ELM much more efficient. Meanwhile, the LCOs obtained by the ELM are in good agreement with numerical solutions. The nonlinear damping can delay the occurrence of secondary bifurcation. On the other hand, it has marginal influence on bifurcation characteristics or LCOs.     

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

Aeroelastic two-level optimization for preliminary design of wing structures considering robust constraints

An aeroelastic two-level optimization methodology for preliminary design of wing struc- tures is presented, in which the parameters for structural layout and sizes are taken as design vari- ables in the first-level optimization, and robust constraints in conjunction with conventional aeroelastic constraints are considered in the second-level optimization. A low-order panel method is used for aerodynamic analysis in the first-level optimization, and a high-order panel method is employed in the second-level optimization. It is concluded that the design of the abovementioned structural parameters of a wing can be improved using the present method with high efficiency. An improvement is seen in aeroelastic performance of the wing obtained with the present method when compared to the initial wing. Since these optimized structures are obtained after consideration of aerodynamic and structural uncertainties, they are well suited to encounter these uncertainties when they occur in reality.     

Friction moment analysis of space gyroscope bearing with ribbon cage under ultra-low oscillatory motion

This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing＇s total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing＇s maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing＇s total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred.     

Determination of thermal expansion coefficients for unidirectional fiber-reinforced composites

In the present work, the coefficients of thermal expansion（CTEs） of unidirectional（UD）fiber-reinforced composites are studied. First, an attempt is made to propose a model to predict both longitudinal and transverse CTEs of UD composites by means of thermo-elastic mechanics analysis. The proposed model is supposed to be a concentric cylinder with a transversely isotropic fiber embedded in an isotropic matrix, and it is subjected to a uniform temperature change. Then a concise and explicit formula is offered for each CTE. Finally, some finite element（FE） models are created by a finite element program MSC. Patran according to different material systems and fiber volume fractions. In addition, the available experimental data and results of other analytical solutions of CTEs are presented. Comparisons are made among the results of the cylinder model,the finite element method（FEM）, experiments, and other solutions, which show that the predicted CTEs by the new model are in good agreement with the experimental data. In particular, transverse CTEs generally offer better agreements than those predicted by most of other solutions.     

基于无网格算法的化学非平衡流数值模拟

为了验证AUSMPW+格式在无网格算法的精度等以及无网格算法能否用于复杂化学非平衡流数值模拟中,首先将AUSMPW+格式推广到无网格算法中,给出了AUSMPW+在无网格算法中的具体形式。其次,将无网格算法应用于带化学反应的多组分气体Euler方程的求解,给出无网格条件下求解化学非平衡流的具体过程。最后,对NACA0012跨声速绕流场、高超声速弹丸绕流场、氢气/氧气诱导燃烧流场、球锥高超声速绕流场、楔体斜爆轰流场进行了数值模拟。数值模拟结果与相关文献计算结果和实验结果吻合较好,表明了AUSMPW+格式在无网格算法中表现较高精度。同时,采用无网格算法能较好地模拟复杂化学非平衡流场,正确分辨复杂的物理现象,为化学非平衡流数值模拟提供一种新的算法,拓宽了无网格算法的应用范围。     

LHT-100霍尔推力器热特性模拟分析

为了对LHT-100霍尔推力器提出热设计优化措施,采用有限元仿真软件进行LHT-100霍尔推力器的稳态、瞬态及空间在轨环境模拟热分析研究,并通过热平衡试验进行了结果比对。分析及试验结果表明,处于工作状态时霍尔推力器的高温部件主要是放电腔、阳极和导磁底座,而受高温影响薄弱部件内线圈、气路组件的温度则分别达到了约401~421℃和141~381℃。热设计优化建议为,在放电腔与内线圈之间增加独立热屏结构后可以有效降低内线圈温度约80~90℃,在阳极气路组件上存在的热应力会是影响霍尔推力器可靠性的重要因素,需要在热设计中得到充分考虑。     

基于自适应核主元分析的EHA系统传感器故障检测

针对核主元分析(KPCA)方法难以选择合适核函数的问题,提出了一种基于自适应核主元分析的传感器故障检测方法,根据训练数据对核函数进行自适应修正,使核函数适应给定的训练数据。对常规数据标准化处理方法进行了改进,提出了一种"均值化"的处理方法,使处理后的数据既能消除不同变量幅值和量纲的影响,又能反映训练数据的全部信息。将此方法应用于机载电动静液作动器(Electro-Hydrostatic Actuator,EHA)系统的传感器故障检测,结果表明,此方法比常规KPCA方法更为先进,具有更好的故障检测性能。     

基于损伤力学的金属材料韧性断裂失效分析

金属韧性断裂是损伤累积的结果,以孔洞演化理论和细观损伤力学模型为基础,将韧性断裂机制

分为拉伸型和剪切型两种类型,提出了一个适用于不同变形路径的统一形式的韧性断裂准则。通过编写用户

材料子程序VUMAT,将韧性断裂准则嵌入到ABAQUS 有限元软件的准静态算法主程序中,模拟了航空铝合金

LY12CZ(Kt =1 和3)单向拉伸时材料损伤累积、裂纹萌生、扩展直至韧性断裂的物理全过程,并通过拉伸试验

验证了模型的有效性。韧性金属材料孔洞断裂机制研究表明,单调加载过程中宏观裂纹的形成是孔洞在夹杂

物和第二相微粒周围形核、长大直至聚合的结果。