星用非金属材料出气污染性质原位测试设备研制

成功研制了星用非金属材料出气污染性质原位测试设备， 可原位、连续、定量测试星用非金属材料出气可凝挥发物，给出全过程的出气数据。测试系统稳定、测试仪器灵敏、最小可检达４．４×１０－ ８ｇ／ｃｍ ２。是我国目前唯一的多功位星用非金属材料出气污染高灵敏度原位测试设备。     

模型旋翼与全尺寸旋翼风洞试验结果的比较

本文介绍了旋翼原理样机4m模型旋翼在CARDC 8m×6m闭口风洞的试验结果与全尺寸旋翼在俄罗斯TSAGI T101开口风洞试验结果的比较.     

固体燃料ATR涡轮/压气机匹配方法研究

为了获得固体燃料空气涡轮火箭发动机(SP-ATR)中涡轮和压气机的匹配工作特性,建立了涡轮和压气机的工作特性模型,根据SP-ATR转速、功率和背压平衡的工作特点,分别基于涡轮和压气机的工作环境先后采用两种不同的方法完成了二者的匹配。对比两种匹配方法得出结论:(1)基于涡轮的匹配方法与转速稳定过程一致,可确定特定飞行环境中发动机的转速;(2)基于压气机的匹配方法需要条件更少、适用范围更广,可用于特定转速调控方案下驱涡燃气流量的确定。两种匹配方法的计算结果相对Ax STREAM仿真结果的最大误差为10.75%,两种匹配方法的计算结果相差不超过8%。将建立的匹配方法应用于HARM弹自主爬升飞行过程,得到SP-ATR驱涡燃气流量的定量调控规律。     

固体燃料空气涡轮火箭发动机工作模式

根据SP-ATR目前存在的燃气难以兼顾清洁和富燃的问题,文章提出将原本由1股燃气单独承担驱动涡轮和补燃功能的工作模式分解为由2股燃气分别担负驱涡和补燃功能的工作模式。通过对比分析该工作模式的SP-ATR和固冲发动机、涡喷发动机工作特点,提出了适合该形式SP-ATR的性能计算模型,得到其飞行包线,发现该SP-ATR工作包线宽广,可完全包含涡喷和固冲发动机的工作包线。在此基础上,计算得到了SP-ATR在不同空域和速度条件下的飞行性能及变化规律:(1)随飞行高度和速度的增加,其比冲、比推力增加,但性能随外弹道变化幅度较小,整个工作范围性能稳定;(2)在近地面和低空SP-ATR均可实现低空亚音速盘旋和5 km高度以上的超音速飞行,且在比冲高于6 700 N.s/kg,同时保持比推力大于1 100 N.s/kg;(3)高空SP-ATR工作高度速度范围宽,比冲性能与冲压发动机相当,比推力为冲压发动机的2倍,相同飞行速度条件下飞行高度增加比冲增加、比推力增加,具有在更高高度巡航潜力,高空性能优势明显。     

载人航天器空气环境参数控制非定常仿真分析

为支持乘员在轨驻留,载人航天器需通过空气环境控制系统将众多设计参数和空气环境参数控制在指标范围内。文章建立了一种载人航天器空气环境非定常控制仿真分析模型,包括舱体模块、航天员模块、舱压控制模块、温湿度控制模块以及CO2净化模块。利用该模型分析了载人航天器空气环境参数随乘员代谢水平的非定常变化趋势,并评估了控制系统的工作性能。结果表明:乘员代谢水平变化对空气环境参数有显著影响,通过调节控制系统运行参数可将各空气参数控制在有效指标范围内。人区温度与O2分压、CO2分压和人区湿度有密切的影响关系,不可孤立地进行分析。为载人航天器空气环境参数控制系统的设计和流程改进提供了依据。     

Sliding mode control based guidance law with impact angle constraint

The terminal guidance problem for an unpowered lifting reentry vehicle against a sta- tionary target is considered. In addition to attacking the target with high accuracy, the vehicle is also expected to achieve a desired impact angle. In this paper, a sliding mode control （SMC）-based guidance law is developed to satisfy the terminal angle constraint. Firstly, a specific sliding mode function is designed, and the terminal requirements can be achieved by enforcing both the sliding mode function and its derivative to zero at the end of the flight. Then, a backstepping approach is used to ensure the finite-time reaching phase of the sliding mode and the analytic expression of the control effort can be obtained. The trajectories generated by this method only depend on the initial and terminal conditions of the terminal phase and the instantaneous states of the vehicle. In order to test the performance of the proposed guidance law in practical application, numerical simulations are carried out by taking all the aerodynamic parameters into consideration. The effec- tiveness of the proposed guidance law is verified by the simulation results in various scenarios.     

Aeroelastic two-level optimization for preliminary design of wing structures considering robust constraints

An aeroelastic two-level optimization methodology for preliminary design of wing struc- tures is presented, in which the parameters for structural layout and sizes are taken as design vari- ables in the first-level optimization, and robust constraints in conjunction with conventional aeroelastic constraints are considered in the second-level optimization. A low-order panel method is used for aerodynamic analysis in the first-level optimization, and a high-order panel method is employed in the second-level optimization. It is concluded that the design of the abovementioned structural parameters of a wing can be improved using the present method with high efficiency. An improvement is seen in aeroelastic performance of the wing obtained with the present method when compared to the initial wing. Since these optimized structures are obtained after consideration of aerodynamic and structural uncertainties, they are well suited to encounter these uncertainties when they occur in reality.     

表面介质阻挡放电等离子体体积力实验

采用粒子图像测速(PIV)技术,在2200,4800,7300,14600Pa空气压力条件下,测量了高频高压表面介质阻挡放电(surface dielectric barrier discharge,SDBD)等离子体诱导流场.根据速度场和N-S方程求解了等离子体体积力分布,分析了空气压力和激励器电压对等离子体体积力影响.实验结果表明:相同空气压力时,激励器电压越高体积力越大.相同激励器电压时,体积力随空气压力升高减小.在体积力分布区域,体积力方向一致,较大体积力区域分布于体积力方向线上游,流场高速流动区域紧挨较大体积力分布区域,位于体积力方向线下游.