机翼边界层的横流稳定性分析和转捩预测

通过求解经典O-S方程(LST)、扩展的O-S方程(EOS)和线性抛物化稳定性方程(LPSE),对展向无限长、后掠角25°、迎角0°、来流Mach数0.8、单位Reynolds数6.79×106/m的机翼边界层进行了稳定性分析,结合eN方法进行了转捩预测。研究发现无限长后掠机翼在(x,ω)平面上的中性曲线没有下支,在(x,β)平面上的中性曲线呈反拇指的形状,横流不稳定性在机翼前缘占主导作用。当外界扰动进入边界层后,幅值将被直接放大,对于频率相同的扰动,首先是展向波数β大的增长起来,演化到一定位置开始衰减,然后是展向波数β小的逐渐增长起来,并且增长的指数N逐步超过波数大的扰动。转捩在机翼前缘完成,引起转捩的扰动波的展向波长约为2mm。     

射流伺服阀用放大型超磁致伸缩执行器建模及分析

为提高射流伺服阀的动态性能,设计了采用桥式微位移放大机构的射流伺服阀用放大型超磁致伸缩执行器(AGMA)。建立了计输入位移损失的放大机构模型以及非线性位移输出理论模型,并采用有限元法对所建放大机构模型进行了对比验证,结果表明:放大机构的输入刚度模型最大误差0.78N/μm,放大倍数模型最大误差0.22,放大倍数受输入位移影响较小。最后,试验研究了AGMA的静动态特性,结果显示:控制电流在-0.5A到0.5A缓慢变化时,AGMA输出位移约为78μm;当控制电流从-0.5A跃变到0.5A时,其峰值位移约为71μm,峰值时间约为0.014s,调节时间小于0.1s;当控制电流幅值为0.5A时,其输出位移幅频宽40Hz,谐振频率约为30Hz。     

Flutter analysis of an airfoil with nonlinear damping using equivalent linearization

The equivalent linearization method （ELM） is modified to investigate the nonlinear flut- ter system of an airfoil with a cubic damping. After obtaining the linearization quantity of the cubic nonlinearity by the ELM, an equivalent system can be deduced and then investigated by linear flut- ter analysis methods. Different from the routine procedures of the ELM, the frequency rather than the amplitude of limit cycle oscillation （LCO） is chosen as an active increment to produce bifurca- tion charts. Numerical examples show that this modification makes the ELM much more efficient. Meanwhile, the LCOs obtained by the ELM are in good agreement with numerical solutions. The nonlinear damping can delay the occurrence of secondary bifurcation. On the other hand, it has marginal influence on bifurcation characteristics or LCOs.     

Aeroelastic two-level optimization for preliminary design of wing structures considering robust constraints

An aeroelastic two-level optimization methodology for preliminary design of wing struc- tures is presented, in which the parameters for structural layout and sizes are taken as design vari- ables in the first-level optimization, and robust constraints in conjunction with conventional aeroelastic constraints are considered in the second-level optimization. A low-order panel method is used for aerodynamic analysis in the first-level optimization, and a high-order panel method is employed in the second-level optimization. It is concluded that the design of the abovementioned structural parameters of a wing can be improved using the present method with high efficiency. An improvement is seen in aeroelastic performance of the wing obtained with the present method when compared to the initial wing. Since these optimized structures are obtained after consideration of aerodynamic and structural uncertainties, they are well suited to encounter these uncertainties when they occur in reality.     

基于ANSYS的机翼动力学分析

针对无人机在挂载导弹飞行和发射导弹时,无人机机翼由于受到多种载荷影响所产生的应力应变,应用ANSYS软件动力学分析,计算模拟了机翼在受到多种载荷影响时所产生的应力分布和应变量。分析结果表明,由于外挂物重量和机翼周围气动流场的影响,机翼会产生不同程度的颤振和扭转,其研究结果对合理设计机翼结构具有一定的参考意义。     

飞机机翼结构型式的拓扑优化

<正>在形状优化和尺寸优化已经相当成熟的今天,对于结构的设计已经很局限了,随着拓扑优化的发展,设计师可以从根本上改变结构设计,更大程度地减轻结构重量,在飞机结构设计方面,可以很好地帮助飞机设计人员定量设计寻找机翼结构布局。拓扑优化在近20年里逐渐成为学术与工程领域的研究热点之一,从早期的离散体拓扑优化发展到连续体结构的拓扑优化,从简单的二维结构拓扑优化发展到更加复杂的三维连续体结构的拓扑优化,近几年已经广泛应用于汽     

大展弦比机翼非线性颤振分析与优化

<正>气动弹性问题一直以来都困扰着飞行器设计人员,现代飞机远没有摆脱气动弹性问题所带来的困扰,国内外研究结果表明,气动弹性优化设计能有效的改善机翼的气动弹性性能,进而提高飞机的整体性能,已成为现代飞机设计过程中必不可少的环节之一。随着先进的复合材料在飞机上得到广泛的应用,针对复合材料机翼的优化研究,得到了越来越多学者的关注。合理的优化可提高飞机发散速度甚至消除发散现象。在复合材料机翼的优化设计     

一种基于承载效率准则的复合材料机翼结构布局优化方法(英文)

提出一种针对大型复合材料机翼结构的二级布局优化策略。系统级根据结构形变调整设计指标,子系统级优化结构布局以满足系统级约束。将机翼壁板中各种临界失效载荷的接近程度作为评判结构效率的标准,通过将结构效率作为优化目标,保证了所求解问题的连续性。加筋壁板通过等效的正交异性板模拟,并根据能量原理预测总体失稳载荷。讨论了加强筋支持弹性对于蒙皮抵抗局部失稳性能的影响,并通过神经网络代理模型对其进行逼近。采用解析模型对失效特性做出评估,减少了计算资源的占用。最后以一种大型机翼结构的综合优化作为算例,计算结果满足设计要求,验证了该方法的可行性。     

MD90-30干线飞机机翼部件互换协调的特点

ＭＤ９０ － ３０ 干线飞机的机翼部件划分为１４ 个互换协调部位，本文从架外安装、部件对接、组件装配工序分析了其互换协调特点，并同我国传统做法进行了对比分析