Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

基于EWT的离心压气机出口动态压力样本熵分析

以800 kW离心压气机从稳定状态经过过渡过程进入喘振状态时段的出口动态压力为研究对象，采用经验小波变换并结合样本熵特征，分析了系统在不同工况下的复杂特性。首先，在分析系统动态压力波形特征的基础上，采用经验小波变换并结合皮尔逊相关系数进行信号的提取。其次，研究了提取信号的样本熵与系统工作状态变化的关联关系，并讨论了经验小波的分解层数和样本熵的维数对分析结果的影响。最后，通过将白噪声加入原始信号以验证该方法的抗干扰性能。研究结果显示：当系统由稳态进入喘振状态时，系统出口动态压力的样本熵表现出明显的突变特性，其值由0突变至0.7左右。从系统参数的选择角度，样本熵维数的变化对系统特征的分析影响较小。并且，采用该方法抗干扰性能较好。     

基于CFD高精度算法的雷电电磁场研究

雷电空间电磁场一直是电磁领域研究的热门，成熟的算法例如有限时域差分法（FDTD），传输线矩阵法（TLM）以及频域的矩量法（MoM）在计算雷电问题方面都有广泛的应用。由于计算流体力学（CFD）中的Euler方程与电磁学中的Maxwell方程有着相同的守恒形式，而且采用间断伽辽金方法（DG）已经在流场问题上得到广泛的尝试，因此引入了基于计算流体力学的DG方法来离散时域Maxwell方程，并采用网格分区并行技术加速计算，使用基于DG的圆球雷达散射截面积（RCS）算例进行测试，数值结果一致表明DG算法在求解电磁场问题上的可行性，之后通过计算一段近场雷电通道的电场分布并与解析解、某算法仿真解对比，数据基本吻合，说明该方法适合于雷电电磁场的计算。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种基于VPL 的元器件快速建模方法

为了更好地落实航空电子模块的可制造性设计审查工作,结合航空电子模块产品特点和技术要求,建设了基于Valor软件的PCB/PCBA设计与检测自动化分析系统.元器件模型库作为该系统的必要组成部分,其覆盖范围和数据精度对审查结果至关重要.本文将从元器件模型库建设必要性、建设过程和建模工艺要求三个方面进行阐述,并提出一种基于Valor VPL的元器件快速建模方法,应用结果表明,该方法能够高效构建满足系统审查精度的元器件模型,使大规模元器件模型库的建设成为可能.     

基于DLatLRR与VGG Net的红外与可见光图像融合

针对红外与可见光图像融合中特征损失严重、显著目标不突出的问题，提出了一种低秩表示分解与深度神经网络相结合的图像融合算法。首先，对源图像进行潜在低秩表示分解（DLatLRR），得到相应的低秩部分、显著部分及稀疏噪声。然后，分别采用16层的VGG Net模型和联合特征加权算法对低秩部分与显著部分进行融合，舍弃二者的稀疏噪声。最后，对融合得到的低秩部分和显著部分进行图像重建，得到最终的融合图像。实验结果表明:与其他算法进行比较，所提算法能够对图像的深层次细节特征进行融合，突出场景中的感兴趣区域，且融合图像的相关差异和、结构相似性、线性相关度等多种客观指标均有所提升，提升最大值分别为0.73、0.15、0.11，噪声产生率的最大缩减值为0.041 2。      

基于鸽群优化算法的实时避障算法

为保证机器人能安全无碰撞地抵达目标位置，提出一种在改进版圆形扩张（CSE+）法中融合鸽群优化算法的实时避障算法。所提算法引入对障碍物密集程度的判断机制，在障碍分布密集时选择最安全的路径，在障碍物分布稀松的环境中，利用鸽群优化算法在安全范围内寻找下一目标最优位置。此外，还引入了搜索树，可实现死角的检测与避免。仿真结果显示:所提避障算法能提高路径规划的性能，在障碍物分布稀松时效果更加明显，且可实现死角检测并能通过狭长通道。      

基于DOA聚类算法的ARM抗有源诱偏技术研究

有源诱偏技术是雷达对抗反辐射导弹的一种重要手段,可以大大降低反辐射导弹的作战效能。为提高对敌目标的精确打击能力,在分析闪烁诱饵诱偏原理的基础上,针对有源诱偏干扰下被动雷达测角精度与稳定度不高的问题,通过对有源诱偏信号的时域特征进行分析,提出一种基于脉冲前沿检测的DOA聚类分选算法,找出前沿超前的辐射源信号,实现了高性能抗有源诱偏干扰和高精度抗干扰测向。仿真结果表明,该技术可以有效对抗四点源有源诱偏干扰。     

基于复杂网络的车载自组织网络脆弱性分析

车载自组织网络(VANET)作为智能交通的重要基础应用，其安全稳定地运行是交通系统乃至社会经济可持续发展的需要。以最大连通度、连通分支平均规模、全局网络效率等参数为脆弱性测度指标，基于复杂网络理论，应用车辆仿真软件(VanetMobiSim)建立了VANET网络拓扑模型，详细研究了在随机攻击和蓄意攻击模式下脆弱性量化指标随节点移除比例的变化关系；通过仿真实验分析了节点密度、信号辐射半径及不同攻击策略对VANET脆弱性的影响。仿真结果表明:VANET在蓄意攻击下比较脆弱，基于节点介数的蓄意攻击效能最强；节点密度、信号辐射半径越小，VANET连通性越差，网络越脆弱。所提方法和结果为VANET拓扑控制优化和网络管理决策提供了理论依据。