Working and walking on small asteroids with circumferential ropes

The low gravity of a small asteroid would present a challenge for an astronaut attempting to work on its surface. Extravehicular activities (EVAs) of the sophistication of the Apollo Moon missions are not likely to be possible if astronauts attempt to walk freely on the asteroid, hover above its surface, or anchor locally into the regolith. Manipulating large rocks, drilling, and excavating at multiple locations is a high priority science objective, but would be difficult without a hold-down mechanism. If the asteroid has even a small rotation rate, maneuvering precisely over its surface could be cumbersome. A plausible means of conducting complex EVAs is to tie ropes entirely around the asteroid, under which the astronaut is pushed downward onto the asteroid surface by the tension in the rope. The downward force provides an artificial gravity that permits the astronaut to drill, excavate, hammer, and carefully document materials on the surface without the worry of being thrown from the asteroid. An astronaut could also use the ropes as handholds or guides to maneuver freely over the surface.     

航空用国产碳纤维/双马树脂复合材料湿热特性

针对1种航空用国产T700级碳纤维和4种双马树脂（QY9611、5429、QY9512、QY8911-4），采用3种湿热条件（100℃水煮、70℃水浸、70℃/85%相对湿度）对其复合材料单向层板进行湿热处理，通过研究吸湿量、扩散系数、显微结构、化学成分、耐热温度及力学性能，分析了复合材料的湿热特性。结果表明，4种复合材料在3种湿热条件下的吸湿行为均符合Fick第二扩散定律，100℃水煮时平衡吸湿量和扩散系数最大，70℃/85%相对湿度时两者最小。4种复合材料吸湿速度有明显区别，这与其原材料形式和成型工艺不同有关。湿热处理未导致复合材料内部产生损伤和化学变化，主要引起增塑效应，导致玻璃化转变温度降低。复合材料的90°拉伸性能测试结果表明，高温和吸湿耦合作用下复合材料力学性能衰减更为明显，破坏模式由基体开裂转变为界面脱黏和开裂。      

基于混合卡尔曼滤波器组故障传感器定位方法

为了在发动机性能蜕化与传感器故障并存的情况下实现故障传感器的定位与部件蜕化情况的估计,并实现故障诊断基准数据的修正,构建了1种包含了机载模型与线性卡尔曼滤波器的组合结构混合卡尔曼滤波器组。该卡尔曼滤波器组能够在之前所描述的故障/蜕化耦合情况下定位故障传感器,并得到较为准确的部件蜕化估计结果。为了验证了混合卡尔曼滤波器组的有效性,进行了相关仿真。仿真结果表明:混合卡尔曼滤波器组能够在发动机动态过程中遭遇传感器故障与部件蜕化并存的情况下完成故障定位与蜕化估计。     

A Simple Real-Time Incoherent Optical Correlator

The Theory and experimental results of a simple optical correlator are given. The optical components consist only of an incoherent source, condensing, collimating, and transforming lenses, and a photodetector. For real-time operation, a reference signal on a photographic transparency is correlated with an unknown signal on an ultrasonic light modulator. The output is a function of time proportional to the correlation function's amplitude rather than the squared amplitude generated by other optical correlators. When used for correlation in radar signal processing, the optical processor may be used for both pulse coding and decoding (pulse expansion and compression) and the decoded signal is shown to be described by Woodward's ambiguity function. The experimental results demonstrated the validity of the theory in both real and scaled time. However, developmental work is still required to improve the operation.     

Electromagnetic dissociation and space radiation

Relativistic nucleus–nucleus reactions occur mainly through the strong or electromagnetic (EM) interactions. Transport codes often neglect the latter. This work shows the importance of including EM interactions for space radiation applications.     

The results of flight tests of an attitude control system for the Chibis-M microsatellite

The attitude control system of the Chibis-M microsatellite is described. Results of flight experiments on damping the initial angular velocity (made using magnetorquers) are considered, as well as stabilization in the orbital referece frame, and orientation of solar arrays toward the Sun using reaction wheels. The operation of algorithms of satellite attitude determination on sunlit and shadow segments of the orbit is also under study. The general logic of operation of the attitude control system in automatic mode is presented and discussed.     

7150铝合金热变形行为及微观组织

采用Gleeble热模拟机进行热压缩实验,研究7150铝合金在变形温度为300~450℃、应变速率为0.01~10s-1条件下的变形行为,采用Zener-Hollomon参数法构建合金高温塑性变形本构方程,并对变形后的微观组织进行分析。研究表明:7150铝合金的流变应力随应变速率增大而增大,随变形温度增大而降低。该合金热压缩变形的流变应力行为可用双曲正弦形式的本构方程描述,其参数A为4.161×1014s-1,α为0.01956 MPa-1,n为5.14336,热变形激活能Q为229.7531k J/mol。随着温度升高和应变速率降低,动态再结晶逐渐取代动态回复成为合金的主要软化机制。     

复合材料副翼典型结构件的VARI工艺模拟及试验验证

在复合材料液体成型工艺过程中,通过计算机软件的模拟研究,可以预先判断树脂在增强体中的流动形式和获得树脂的注模时间以及注模压力,进而为实际成型工艺提供参考设计。本文利用PAM-RTM模拟软件对复合材料副翼典型结构件的树脂流动过程进行了模拟计算。根据达西定律推导出树脂在增强纤维中一维流动渗透率计算公式,分别对增强纤维、缝线纤维进行了渗透率测试,在此基础上对渗透率数值进行了修正。利用渗透率修正值采用不同的流道设计方案对树脂注模过程进行了模拟研究,根据模拟结果最终选择合理的注射方式和流道布局。对所选方案进行了工艺试验验证,并对结构件进行了超声无损检测。结果显示:理论充模时间和试验充模时间基本一致,结构件没有内部缺陷,树脂填充完全,模拟工艺计算有效。     

敏捷型遥感卫星相机热防护门应用研究

针对敏捷型遥感卫星相机变化的外热流,以及热防护门(简称热门)对相机热设计产生的影响,建立带热门的相机热模型,采用Thermal Desktop软件对带热门相机在轨飞行期间的温度变化进行仿真。仿真结果表明,使用热门将大幅降低相机的主动加热功率。对热门开启后相机的最长成像时间进行分析,热门开启后6min,相机次镜支撑组件无法满足相机热设计要求,可在次镜安装板背部包覆多层隔热材料解决这一问题。文章的研究结果,对遥感卫星热门与热控系统的耦合设计具有一定的参考价值。     

面向空间容迟容断网络的路由算法研究

将空间网络作为一种典型的容迟/容断网络(Delay/Disruption Tolerant Network,DTN),同时利用空间网络星座拓扑的规律性和可预见性,通过构造链路通断时间图,快速建立虚拟拓扑路由表;针对路由过程中可能出现的链路中断问题,设计了拥塞控制机制、正常中断机制和链路失效机制来提高路由效率;在The ONE网络仿真平台中对提出的时间图路由算法(Time-GraphRouter)进行了仿真,并与传染路由(EpidemicRouter)、转发等待路由(SprayAndWaitRout-er)、预测路由(ProphetRouter)三种路由机制进行了对比。仿真结果表明,文章提出的路由算法的平均投递率达到了0.98以上,综合性能优于其他三种路由算法。