全文获取类型
收费全文 | 951篇 |
免费 | 305篇 |
国内免费 | 161篇 |
专业分类
航空 | 751篇 |
航天技术 | 205篇 |
综合类 | 90篇 |
航天 | 371篇 |
出版年
2024年 | 2篇 |
2023年 | 25篇 |
2022年 | 59篇 |
2021年 | 66篇 |
2020年 | 50篇 |
2019年 | 42篇 |
2018年 | 61篇 |
2017年 | 61篇 |
2016年 | 46篇 |
2015年 | 63篇 |
2014年 | 74篇 |
2013年 | 61篇 |
2012年 | 65篇 |
2011年 | 75篇 |
2010年 | 87篇 |
2009年 | 81篇 |
2008年 | 89篇 |
2007年 | 65篇 |
2006年 | 61篇 |
2005年 | 48篇 |
2004年 | 51篇 |
2003年 | 24篇 |
2002年 | 32篇 |
2001年 | 17篇 |
2000年 | 22篇 |
1999年 | 14篇 |
1998年 | 13篇 |
1997年 | 14篇 |
1996年 | 6篇 |
1995年 | 6篇 |
1994年 | 4篇 |
1993年 | 8篇 |
1992年 | 5篇 |
1991年 | 4篇 |
1990年 | 4篇 |
1989年 | 4篇 |
1988年 | 2篇 |
1987年 | 1篇 |
1986年 | 1篇 |
1985年 | 1篇 |
1983年 | 1篇 |
1982年 | 1篇 |
1977年 | 1篇 |
排序方式: 共有1417条查询结果,搜索用时 15 毫秒
41.
42.
为了解结构参数对圆转矩形内喷管再生冷却换热的影响,设计了多个圆转矩形喷管,考虑了三种结构参数:转方位置、出口高宽比和出口圆角大小的影响。采用有限体积法求解三维可压缩的N-S方程对其内部流动和换热进行了数值模拟。湍流模型采用标准的k-ε双方程模型,壁面附近的流动和传热采用壁面函数法处理,速度与压力的耦合采用SIMPLE算法求解。结果表明:在型面一阶导数连续的情况下,转方位置对圆转矩形内喷管的换热影响不大;出口高宽比对圆转矩形内喷管的换热影响较大,出口高宽比不能太小,否则影响内喷管流场和换热;出口圆角大小影响内喷管周向上的温度分布,圆角太小造成周向温度分布不均匀。 相似文献
43.
44.
45.
机匣包容性破坏势能法的试验验证 总被引:1,自引:0,他引:1
为了验证航空发动机机匣包容性破坏势能法,本文完成了20次模型机匣包容性冲击试验,得到了模型叶片撞击模型机匣时的速度、应变响应和模型叶片撞击模型机匣过程的高速摄影照片。试验结果表明,该模型机匣的非包容失效模式主要是剪切破坏。本文还采用数值分析方法对机匣包容性进行了模拟,计算结果与试验结果吻合良好。 相似文献
46.
基于仿生的大展弦比机翼结构布局形式研究 总被引:1,自引:0,他引:1
为了探讨大展弦比直机翼的结构布局形式,本文借鉴自然界中的鱼骨与树叶的叶脉形式,利用有限元分析与满应力优化作为设计手段,对3种不同的结构布局形式(A构型、B构型和常规构型)开展基于强度、刚度以及质量条件限制下有关响应的对比研究。计算结果表明:在不同尺度的等质量条件限制下,“A构型”弯曲刚度最大,扭转刚度居中;“B构型”弯曲刚度居中,扭转刚度最小;“常规构型”弯曲刚度最小,扭转刚度最大。分析结果证明,机翼的翼肋布置应该“适当地”倾斜。最后给出3点结论。 相似文献
47.
48.
49.
WAN Min ZHANG Wei-hong TAN Gang QIN Guo-hua 《中国航空学报》2007,20(3):282-288
A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions. 相似文献
50.