多层隔热材料的性能研究

本文从多层隔热材料的实际应用条件出发,研究了它们在几种层密度下的隔热性能,特别包括了在层密度较高情况下的性能。为了改善多层隔热材料的隔热性能,采用了间隔几层隔离层的组合形式。压缩负荷对层密度、隔热性能的影响也进行了初步的研究。     

“AP/HTPB/Al/催化剂”推进剂燃烧模拟计算方法

本文以我们在文献[1～4]中提出的“AP/HTPB/Al”推进剂燃烧模型为基础,首先讨论了催化剂作用部位与推进剂燃速、压力指数变化的关系,然后引入一个催化剂作用因子B.并以二茂铁系列催化剂为例,对模型中的几个与二茂铁催化剂作用部位相连系的反应动力学参数作“催化作用因子”校正,计算研究了四种二茂铁催化剂用量对燃速、压力指数的影响规律.计算结果与实验符合得很好,相对误差均小于±10%,证明本文提出的模拟计算方法具有较高的可靠性.     

基于IRI-2012模型广州地区f_0F_2实测与预测的对比分析

利用广州台站(23.2°N,113.3°E)的实测数据和IRI-2012模型提供的预测数据,对比分析了2013年广州地区f_0F2的变化特征.结果表明,IRI-2012模型能够较好预测该地区f_0F_2的变化趋势,并且CCIR参数得到的预测值比URSI参数更接近实测值;预测值与实测值存在系统偏差,在11:00 LT-06:00 LT时段,观测值均比预测值大,其他时段则相反.在日落后至午夜前时段,预测值与实测值有较大差距.绝对偏差的极值点通常出现在20:00 LT左右,最大超过4 MHz.相对偏差变化比较明显的时段是午夜后至凌晨;在02:00 LT或04:00 LT及06:00 LT附近,可能会出现双误差峰值点,最大超过0.4;但在σ变化很大的20:00 LT附近,相对偏差却变化不大.夜间增强现象会使得偏差增大,导致预测值不能很好反映实测f_0F2的变化.     

一种悬挂物兼容飞机航电与武器总线的设计方法

在某悬挂物作为通用系统挂装不同型号飞机时,由于不同型号飞机对该悬挂物采用航电和武器两种不同的总线通信方式,导致该悬挂物不能兼容挂载多型飞机。本文针对现有的总线应用情况,提出了一种悬挂物可兼容飞机不同总线通信方式的设计方案,并给出了方案的具体实现方法。     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

Fault Estimation and Accommodation for a Class of Nonlinear System Based on Neural Network Observer

The problem of fault estimation and accommodation of nonlinear systems with disturbances is studied using adaptive observer and neural network techniques.A robust adaptive learning algorithm based on switchingβsmodification is developed to realize the accurate and fast estimation of unknown actuator faults or component faults.Then a fault tolerant controller is designed to restore system performance.Dynamic error convergence and system stability can be guaranteed by Lyapunov stability theory.Finally,simulation results of quadrotor helicopter attitude systems are presented to illustrate the efficiency of the proposed techniques.     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

任务型教学法的任务设计

任务型教学法是新兴的一种强调“在做中学”(learning by doing)的语言教学方法，是我国外语课程教学改革的一个走向，吸收了以往多种教学法的优点而形成。任务是任务型教学法中一个重要概念。要使任务型教学法更好地发挥作用，任务的设计就显得尤为重要。在任务设计中，要注意任务与人本主义、任务与文化性、任务与教师角色之...     

Particle swarm optimization applied to hypersonic reentry trajectories

This paper presents the novel use of the particle swarm optimization(PSO)to generate the end-to-end trajectory for hypersonic reentry vehicles in a quite simple formulation.The velocitydependent bank angle profile is developed to reduce the search space of unknown parameters based on the constrained PSO algorithm.The path constraints are enforced by setting the fitness function to be infinite on condition that the particles violate the maximum allowable values.The PSO algorithm also provides a much easier means to satisfy the terminal conditions by adding penalty terms to the fitness function.Furthermore,the approximate reentry landing footprint is fast constructed by incorporating an interpolation model into the standardized bank angle profiles.Numerical simulations demonstrate that the PSO method is a feasible and flexible tool to generate the end-to-end trajectory and landing footprint for hypersonic reentry vehicles.     

某型三叶螺旋桨的设计及性能试验

根据飞行速度、需用拉力、螺旋桨转速等参数,设计了某型飞机的三叶螺旋桨,获得了弦长和桨叶角沿着径向的分布.制造了三叶复合材料螺旋桨（直径为1.75m）,在螺旋桨试验台上测试了不同转速下螺旋桨的拉力.为了获得螺旋桨的动态性能,制造了螺旋桨的缩比模型（直径为0.96m）,在西北工业大学NF-3风洞的三元试验段测试了螺旋桨的气动性能数据,包括:拉力、扭矩、功率、效率.结果表明:螺旋桨最大效率为85.63%,所设计的三叶复合材料螺旋桨适用于螺旋桨需用功率为70kW左右的发动机（比如Rotax912）,提出的螺旋桨设计方法具有较好的应用价值.