W波段FMCW SAR系统实现与试验

与C波段、X波段和Ka波段相比,W波段的调频连续波(FMCW)合成孔径雷达(SAR)系统因具有更高的分辨率,更易实现低功耗与小型化而备受关注。W波段波长短,因此该波段的FMCW SAR更适用于短距离成像。提出一种W波段FMCW SAR系统的设计方案,根据提出的系统方案与指标,实现W波段FMCW轨道SAR系统的样机研制。该系统分辨率可达5 cm。系统样机试验在上海交通大学的多功能船模拖拽水池完成。设置不同目标进行成像试验,最终得到多组有效试验数据,并基于改进的RD算法进行数据处理,得到理想的SAR图像。经分析可知,系统实际分辨率优于5 cm。试验结果证明了W波段FMCW SAR系统的可行性与有效性。     

新型弹簧床结构的HAN基发动机技术

为改善硝酸羟胺(HAN)基发动机催化剂在长时间工作的工况下容易发生破碎而产生空穴的现象，本文提出一种新型弹簧床结构发动机设计方法，对发动机催化床进行改进优化设计。该设计可实现，常温环境下弹簧所提供的最大弹力不足以压碎催化剂；同时在高温环境下，弹簧的最小弹力足以克服催化床受到的流动阻力，可大幅提高发动机工作寿命、性能和可靠性。为验证该设计方法的有效性，分别开展了传统结构和新型弹簧床结构的HAN基1N发动机温启动试验。试验结果表明：在相同试验条件下，传统结构1N发动机温启动次数不超过150次，而使用新型弹簧床结构的1N发动机温启动次数超过了500次，且工作性能更优。试验结果证明了该设计方法的有效性，为HAN基发动机长寿命可靠工作奠定了良好的技术基础。     

Enhanced multipath mitigation method based on multi-resolution CNR model and adaptive statistical test strategy for real-time kinematic PPP

This study proposes an enhanced multipath mitigation method based on multi-resolution carrier-to-noise-ratio (CNR) model and adaptive statistical test strategy for real-time kinematic precise point positioning (PPP) applications. The multi-resolution CNR model is established with GPS observation data collected from DOY 152 to 181 of 2019 by 230 globally distributed IGS stations, which used to analyze the relevant factors affecting CNR. Statistical results indicate that the CNR is not only related to the satellite elevation, but also closely related to the receiver types and specific satellite. The maximum difference between different receivers can reach 20 dB for the same satellite at the same elevation. In addition, the performance of the CNR is also obviously different between each satellite, and the maximum difference between different satellites is about 10 dB for the same receiver at the same elevation. Hence, in terms of the method which is based on CNR information for multipath detection and mitigation, the independence of receiver types, satellite and frequency must be considered. With the above analysis, this study developed a multi-resolution CNR model based on different receiver types, different satellites and different elevation firstly. Then, combined with the adaptive statistical test strategy which is based on the difference of CNR between inter-frequency and the difference of CNR between adjacent epochs, the multipath can be detected effectively. For the epoch which affected by multipath, the down-weighted strategy based on CNR is adopted to mitigate the influence of multipath on positioning. Real-time kinematic PPP data are collected to assess the proposed method, and the results demonstrate that the proposed method can detect the multipath effectively, and the detection rate can reach 90.28%. Moreover, after adopting the mitigation strategy, the RMS bias of the east, north and up components are improved about 19.95%, 17.89% and 23.07% compared to the original results, respectively. It is worth noting that this proposed method is also suitable for other GNSS, such as GLONASS and BDS, but the corresponding CNR model must be established simultaneously.     

一种VxWorks BSP 软件自动生成技术的设计与实现

VxWorks BSP 软件的可视化开发和代码自动生成技术是基于BSP 中最小系统配置单元组件化封装 以及常用外设驱动的标准化、通用化、组件化设计与封装实现的。该技术的实现可以使开发人员能够通过在可 视化工具中填写对应硬件信息，完成BSP 软件代码及对应文档的自动生成，实现了软件需求的直观化输入到 需求与设计的黑盒转化。能有效提高软件开发效率，增加软件成熟度，提高软件产品质量。     

Sliding Mode Fault Tolerant Attitude Control Scheme for Spacecraft with Actuator Faults

An active fault tolerant control scheme is investigated for the attitude control systems of spacecraft with external disturbance and actuator faults by using the sliding mode technique. Firstly,the dynamic equations and kinematic equations of spacecraft are given. For the dynamic mode of spacecraft in faulty case,a fault diagnosis component is used for fault detection and estimation by using a nonlinear observer. According to the fault estimation information obtained during the fault diagnosis,the fault tolerant control scheme is developed by adopting the backstepping sliding mode control technique. Meanwhile,the Lyapunov theory is used to analyze the stability of the closed-loop attitude systems. Finally,simulation results for the attitude dynamics models show the feasibility of the proposed fault tolerant scheme.     

HCKF性能评估及其在传递对准中的应用

针对高阶容积卡尔曼滤波(HCKF)算法在传递对准中的应用问题，提出综合运用多变量函数泰勒级数展开和计算复杂度分析的性能评估方法。基于高阶球面-径向容积准则建立HCKF算法模型，并对其估计精度和计算量进行量化和对比分析：HCKF具有5阶泰勒级数展开精度且计算复杂度为O(n 4)，综合性能优于高斯厄米特积分滤波(GHQF)和无迹卡尔曼滤波(UKF)。将三种非线性滤波算法应用到舰机大失准角传递对准系统中，摇摆台试验结果表明：HCKF的估计精度比UKF高17%，计算量比GHQF小2个数量级，与HCKF性能评估结果一致。     

Postcapture stabilization of space robots considering actuator failures with bounded torques

Space robotics is regarded as one of the most impressing approaches for space debris removal missions. Due to the residual momentum of debris, it is essential to stabilize the base rapidly after capture. This paper presents a novel control strategy for stabilization of a space robot in postcapture considering actuator failures and bounded torques. In the control strategy, the motion of the manipulator is not regarded as a disturbance to the base; in contrast, it is utilized to compensate for the limitation of the control torques by means of an inverse dynamical model of the system. Different scenarios where actuators are external mechanisms or momentum exchange devices have been carried out, and for actuator failures, both single- and two-actuator failures have been considered. Regarding to the performance of actuators, control torques are bounded. In cases that either single or two actuators have failed, the base can be stabilized kinematically when actuators are external mechanisms, but can only be stabilized dynamically when only momentum exchange devices are used. Finally, a space robot with a seven-degree-of-freedom manipulator in postcapture is studied to verify the validity and feasibility of the proposed control scheme. Simulation results show that the whole system can be stabilized rapidly.     

Co-registration of Chang’E-1 stereo images and laser altimeter data with crossover adjustment and image sensor model refinement

Topographic information is of fundamental importance for various scientific investigations in lunar and planetary exploration. To provide high-precision, seamless mapping capability, it is critical to co-register image and altimetry data, the two major data sources for topographic modeling. This paper presents a method for co-registration of Chang’E-1 (CE-1) stereo images and laser altimeter (LAM) data with crossover adjustment and refinement of the image sensor model. The crossover adjustment is tested in a larger area (0–60°N, 50–0°W); the image refinement and co-registration with LAM data are tested in an area (46.2–50.0°N, 31.8–28.8°W) within the larger area. Experimental results demonstrate that this co-registration reduces the mean differences of inconsistency from more than 200 m to just 3.21 m in the Z direction of object space. In image space, the mean errors of homologous points both in the column and row directions are reduced to below 0.1 pixel. This indicates that the proposed crossover adjustment of LAM data and refinement of the CE-1 stereo image model can effectively improve co-registration of the two data sets.     

低频靶标法测量CCD相机调制传递函数的仿真

基于用高频靶标法测试调制传递函数（MTF）时不能准确地体现出CCD器件的平均采样的情况。该文探讨用低频靶标法测试MTF，介绍它的原理；通过数字仿真CCD的光学镜头的模糊和采样平均过程，分析不同频率靶标的MTF测试结果，并分析相位造成的影响。     

微量Sc和Zr对Al-Mg-Mn合金组织和性能的影响

研究了添加微量Sc和Zr对系列Al-Mg-Mn合金显微组织和拉伸性能的影响。结果表明：微量Sc和Zr添加到Al-Mg-Mn合金中，热轧态合金的拉伸强度和屈服强度分别提高了75MPa-90MPa和90MPa-94MPa；经冷轧后340℃／1h稳定化退火，合金拉伸强度和屈服强度分别增加了85MPa-95MPa和90MPa。100MPa，而延伸率仍保持在11％-12％；并能显著细化合金的铸态晶粒，强烈抑制合金的热轧态和板材冷轧后退火过程中的再结晶，晶粒组织成纤维状；使合金强化的机制为晶粒细化强化、亚结构强化和铝钪锆化合物粒子引起的析出强化。