拦截高速目标的比例与反比例导引捕获区分析

针对拦截高速目标的作战特点，分析了比例导引(PN)与反比例导引(RPN)的捕获区。首先，通过分析拦截弹与目标的相对运动关系，推导得到了顺轨和逆轨的零控拦截条件，此条件由目标和拦截弹的速度前置角以及二者速度比确定；其次，以拦截弹和目标速度前置角为坐标系，推导得到了PN以及RPN捕获区以及各自导航比设置范围。PN的捕获区由逆轨零控拦截条件以及与其相切且斜率为1/(N-1)的两条直线构成，RPN的捕获区由顺轨零控拦截条件以及与其相切且斜率为1/(-N-1)的两条直线构成；然后，利用函数对称性将PN与RPN捕获区转换到同一坐标区间，得到了相同条件下RPN捕获区要大于PN捕获区的结论；最后，开展了四种情形下的仿真，验证了本文捕获区分析的合理性及有效性。     

An improved numerical method for constructing Halo/Lissajous orbits in a full solar system model

An improved numerical method that can construct Halo/Lissajous orbits in the vicinity of collinear libration points in a full solar system model is investigated. A full solar system gravitational model in the geocentric rotating coordinate system with a clear presentation of the angular velocity relative to the inertial coordinate system is proposed. An alternative way to determine patch points in the multiple shooting method is provided based on a dynamical analysis with Poincare′sections. By employing the new patch points and sequential quadratic programming, Halo orbits for L_1, L_2, and L_3 points as well as Lissajous orbits for L_1 and L_2 points in the EarthMoon system are generated with the proposed full solar system gravitational model to verify the effectiveness of the proposed method.     

单向电永磁作动器结构优化与动态特性分析

针对电磁作动器的使用要求，设计出一种具有能耗低、吸力大及响应快等特点的新型单向电永磁作动器。结合有限元仿真软件，利用有限元法研究作动器的结构参数如铁芯齿形结构、平面结构、无永磁结构、铁芯的倾斜角度及衔铁位移（气隙厚度）等因素对作动器电磁吸力和响应速度的影响。结果表明，电磁吸力随着作动衔铁位移的增加而大幅度减小；倾角结构的铁芯设计能使作动器性能达到最佳，且铁芯的倾斜角度为50°时，电磁吸力有最大值3071N。     

不同密度弹丸对水冰的超高速撞击成坑实验

为了研究冰冻天体表面撞击坑的形成与演化，开展了水冰的超高速撞击成坑实验。使用二级轻气炮发射1.0 mm直径的球形弹丸，以3 km/s、5 km/s和7 km/s速度对圆柱状冰块进行撞击。弹丸材料包括聚碳酸酯和不锈钢两种，冰块温度为253 K。实验观察到了不同弹丸和不同速度条件下，冰块中撞击坑的形貌特征。对撞击坑直径、深度和剖面形状进行了测量，并与文献中铝弹丸对水冰的撞击坑进行了比较分析。获得了水冰撞击坑特征随撞击参数的变化规律，结果表明：撞击坑直径和深度的主导机制不同，坑深主要由弹丸侵彻作用形成，而坑径主要由冰块的剥落所致；坑深比坑径具有更强的对于弹丸密度的依赖性，高密度弹丸撞击坑直径具有比低密度弹丸更强的对于撞击速度的依赖性；撞击坑体积与撞击能量成正比，高密度弹丸形成的撞击坑直径表现出“能量缩比”行为，而低密度弹丸形成的撞击坑直径表现出“动量缩比”行为。     

Last FY-2 Series Satellite Successfully Launched on A LM-3A

正A LM-3A launch vehicle lifted off from the Xichang Satellite Launch Center at21:07 Beijing time on June 5,launching the FY-2H satellite into orbit.This was the 277th flight mission of the LM family launch vehicle.FY-2H was the last flight unit of the     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

酚醛树脂基纳米多孔材料的制备及结构调控

酚醛树脂基纳米多孔材料（Phenolic Resin-based Nanoporous Materials，PNM）是满足新一代航天飞行器轻质、高效隔热需求的新型热防护材料，传统制备方法中需使用超临界干燥技术，制备周期长、成本高。本研究通过两步法，即先合成线性酚醛树脂，再进行溶胶-凝胶的方法，实现了常压干燥PNM的制备。系统研究了固化剂含量、固化温度和固化时间对材料结构的影响和调控作用，分析了影响材料收缩率和热稳定性的因素。结果表明，PNM的微观纳米结构的变化会影响材料干燥后的收缩率，制备大颗粒、大孔径的微观结构更有利于降低材料的收缩率。而PNM的热稳定性主要受交联反应过程形成的化学结构的影响，通过优化固化剂的含量可提高PNM的热稳定性。当固化剂含量为10%，固化温度提高至150℃，固化时间延长至48 h的条件下，获得的PNM有最高的热稳定性（900℃下的残碳率为54.2%）、最发达的孔结构（比表面积为264.0 m²/g、孔容为2.67 cm³/g、平均孔径为40.0 nm）和最小的收缩率（0%）。此PNM制备方法简单、性能优异，在未来航天飞行器上有广阔的应用前景。     

Research on navigation of satellite constellation based on an asynchronous observation model using X-ray pulsar

Pulsar navigation is a promising navigation method for high-altitude orbit space tasks or deep space exploration. At present, an important reason for restricting the development of pulsar navigation is that navigation accuracy is not high due to the slow update of the measurements. In order to improve the accuracy of pulsar navigation, an asynchronous observation model which can improve the update rate of the measurements is proposed on the basis of satellite constellation which has a broad space for development because of its visibility and reliability. The simulation results show that the asynchronous observation model improves the positioning accuracy by 31.48% and velocity accuracy by 24.75% than that of the synchronous observation model. With the new Doppler effects compensation method in the asynchronous observation model proposed in this paper, the positioning accuracy is improved by 32.27%, and the velocity accuracy is improved by 34.07% than that of the traditional method. The simulation results show that without considering the clock error will result in a filtering divergence.     

Anchoring Bolt Detection Based on Morphological Filtering and Variational Modal Decomposition

The pull test is a damaging detection method that fails to measure the actual length of a bolt. Thus,the ultrasonic echo is an important non-destructive testing method for bolt quality detection. In this research,the variational modal decomposition(VMD)method is introduced into the bolt detection signal analysis. On the basis of morphological filtering(MF) and the VMD method,a VMD-combined MF principle is established into a bolt detection signal analysis method(MF-VMD). MF-VMD is used to analyze the vibration and actual bolt detection signals of the simulation. Results show that MF-VMD effectively separates intrinsic mode function,even under strong interference. In comparison with conventional VMD method,the proposed method can remove noise interference. An intrinsic mode function of the field detection signal can be effectively identified by reflecting the signal at the bottom of the bolt.