Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

Mapping mean lake surface from satellite altimetry and GPS kinematic surveys

Lake water height is a key variable in water cycle and climate change studies, which is achievable using satellite altimetry constellation. A method based on data processing of altimetry from several satellites has been developed to interpolate mean lake surface (MLS) over a set of 22 big lakes distributed on the Earth. It has been applied on nadir radar altimeters in Low Resolution Mode (LRM: Jason-3, Saral/AltiKa, CryoSat-2) in Synthetic Aperture Radar (SAR) mode (Sentinel-3A), and in SAR interferometric (SARin) mode (CryoSat-2), and on laser altimetry (ICESat). Validation of the method has been performed using a set of kinematic GPS height profiles from 18 field campaigns over the lake Issykkul, by comparison of altimetry’s height at crossover points for the other lakes and using the laser altimetry on ICESat-2 mission. The precision reached ranges from 3 to 7 cm RMS (Root Mean Square) depending on the lakes. Currently, lake water level inferred from satellite altimetry is provided with respect to an ellipsoid. Ellipsoidal heights are converted into orthométric heights using geoid models interpolated along the satellite tracks. These global geoid models were inferred from geodetic satellite missions coupled with absolute and regional anomaly gravity data sets spread over the Earth. However, the spatial resolution of the current geoid models does not allow capturing short wavelength undulations that may reach decimeters in mountaineering regions or for rift lakes (Baikal, Issykkul, Malawi, Tanganika). We interpolate in this work the geoid height anomalies with three recent geoid models, the EGM2008, XGM2016 and EIGEN-6C4d, and compare them with the Mean Surface of 22 lakes calculated using satellite altimetry. Assuming that MLS mimics the local undulations of the geoid, our study shows that over a large set of lakes (in East Africa, Andean mountain and Central Asia), short wavelength undulations of the geoid in poorly sampled areas can be derived using satellite altimetry. The models used in this study present very similar geographical patterns when compared to MLS. The precision of the models largely depends on the location of the lakes and is about 18 cm, in average over the Earth. MLS can serve as a validation dataset for any future geoid model. It will also be useful for validation of the future mission SWOT (Surface Water and Ocean Topography) which will measure and map water heights over the lakes with a high horizontal resolution of 250 by 250 m.     

Substitution of satellite-based land surface temperature defective data using GSP method

Land surface temperature (LST) as an important environmental variable provides valuable information for earth environmental system modelling. Currently, LST is obtained through satellite thermal sensors at various spatial and temporal resolutions. Although spatially continuous satellite-based LST measurements are intended to overcome the shortcomings of sparse ground-based LST measurements, LST images often contain anomalous values due to the existence of clouds or sensor malfunctioning. The problem becomes more serious where the users deal with high spatial resolution characterized by low temporal resolution. This study examines the capability of a newly developed graph signal processing (GSP) method using two-dimensional single-date thermal data. For this purpose, four Landsat/TIRS datasets are analyzed. The data of five elliptical regions on thermal images are eliminated and then reconstructed through the GSP method and using the LST values of the enclosing rectangles containing the ellipsoids. The results indicate that the temperature variation determined by the GSP method generally conforms to the original image LST values. According to a correlation test conducted on the original image LST and those obtained through the GSP method, the values vary from 58% to 95%, which is an above-the-average rate (RMSE from 0.69 to 2.27). The statistical analysis of the original image LST in both the elliptical regions and the enclosing rectangles containing the ellipsoids indicates that an increase in the variance of LST data causes an increased error in the calculation of temperature by the GSP method, and vice versa. The results of the analysis of variance (ANOVA) and Duncan test indicated that an increase in the number of the non-zero spectral bins would result in increased RMSE values for all the dates and the regions. Moreover, the model errors were significant at the 0.05 level across all the image date and five elliptical study regions. Based on the results, the use of this method is recommended for the reconstruction of LST missing values, where dissimilarity of atmospheric conditions limits the use of other methods that depend on the time series data of various dates and a great deal of data calculation.     

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

ADI方法求解完全跨声速非定常小扰动方程

本文修改了Whitlow的ADI格式,以便求解另一变形的完全跨声速小扰动方程。本文给出的NACA64A006和NACA0012翼型的非定常跨声速流动的计算结果与其它数值结果和实验结果的比较表明本文格式是合理的且便于实际应用的。     

关于一维非定常气─固二相流特征理论的讨论

本文研究了一维非定常气－团二相流的特征，对于目前常用的、包含一定近似的运动方程组，它有两个虚部很小的复根，研究表明这种很小的虚部出现与方程中引入的近似有关。从十多个算例的结果看，这样的虚部不影响人们在工程计算中用该方程组求解初值问题。针对具有上述特征的气－团二相流方程组，本文发展了一种类特征线方法，它保留了双曲型方程特征线方法的若干优点，但它允许方程的特征根中有微小的虚部。含灰气体激波管流动的计算表明，类特征线法具有精度高、数值耗散和弥散小等优点     

精仪工作台定量调整的原理及方法

论述了可调结构仪器工作台的结构、调整原理和调整方法，并以三点支撑结构、锥面支撑结构仪器工作台表面与测量轴线垂直度的调整为例，具体地阐述了调整方法和步骤。