复杂动态环境下无人飞行器动态避障近似最优轨迹规划

针对复杂动态环境下无人飞行器的动态障碍规避问题，基于合理假设建立了无人飞行器和动态障碍的运动学模型，并综合考虑无人飞行器飞行过程中的终端约束、控制输入约束、安全避障约束等，以能量最少为性能指标构建动态避障问题数学描述。之后，针对终端约束和控制输入约束，依据优化模型预测静态规划算法(OMPSP)生成初始轨迹；针对动态避障问题的不等式约束，引入松弛变量并结合滑模变结构控制方法设计松弛变量动力学，实现对一个、多个或同时多个动态障碍的安全规避；最后，依据有限时间微分动态规划(RHDDP)算法进行轨迹优化，获得满足上述各种约束并能规避动态障碍的近似最优轨迹。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

Orbit-attitude-vibration coupled dynamics of tethered solar power satellite

A new orbit-attitude-vibration coupled dynamic model of the tethered solar power satellite (Tethered SPS) is established based on absolute nodal coordinate formulation. The Hamilton’s equation of the system is derived by introducing generalized momentum through Legendre transformation. The correctness of the proposed model is verified by an example. The dynamic characteristics of the Tethered SPS are studied using the symplectic Runge-Kutta method. Simulation results show that the orbital radius and the total energy of the system are well preserved. The attitude of the system is unstable when the mass of the bus system is small. However, the attitude stability is dependent on some other parameters of the system, which requires further studies. It is also found that the average tether force/deformation can be roughly estimated by simplifying the solar panel as a particle. The proposed model can be used to study the orbit-attitude-vibration coupled dynamics and control problems.     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

亚超剪切混合层燃油雾化特性试验研究

为了摸清亚超大梯度剪切混合层内直射式喷嘴的燃油雾化特性，设计了用于向亚超剪切混合流中进行燃油喷射的直射式喷嘴，建立了亚超剪切混合层中燃油雾化试验系统。利用粒子图像测速系统（PIV），对亚超大梯度混合层中油雾场进行测量。通过改变喷嘴流量、喷射角度和喷嘴数量研究不同参数对雾化特性的影响，并应用图像处理技术对亚超大梯度剪切混合层内的油雾场进行分析，总结归纳其雾化规律。试验结果显示：随着流量增大，穿透深度会随之增大，破碎后的颗粒分布峰值所对应的液滴直径会逐渐变小，雾化效果提升；相同流量条件下，喷嘴的角度改变对雾化效果有影响，顺喷和逆喷的雾化效果均好于垂直喷射；逆喷的喷射高度最高，随着流量的增长，燃料将会碰壁；顺喷条件下，随着角度的增加，穿透长度会有所增加；综合燃油轨迹边界，逆喷的效果相对较好。相同流量条件下，喷孔个数的改变对雾化效果和穿透深度的影响不大。     

任意波发生器静态特性的评价

介绍了任意波发生器的主要静态特性指标、校准方法及实现过程。通过一组实验．获得了实际校准结果，并对校准中需要注意的问题进行了讨论。所述方法涉及的静态特性内容比较全面。具有足够的测量准确度、分辨力和稳定性。可用于任意波发生器的静态指标评价和计量。     

薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

用于高压动态校准的快开阀装置

介绍一种高压快开阀装置。它可产生３７０ＭＰａ上升时间小于２０μｓ的阶跃压力，用于对高压传感器进行动态校准。     

塑性动态断裂过程中梁的塑性铰转动因子的确定方法

运用理论分析方法和实测试验方法，探讨了梁在塑性动态断裂过程中，其塑性铰转动因子的变化规律，提出了断裂过程中塑性铰几何转动因子的概念及其确定方法，并以３点弯曲梁理论分析解为例，计算了梁在塑性动态断裂过程中，其塑性铰转动因子的变化规律。该计算结果与３点弯曲梁动态断理解实验实测相一致。理论分析进一步明确了梁的塑性铰转动因子具有几何与物理两种不同的本质含意，并可直接用于修正梁的塑性动态断裂的理论分析解。     

飞机横侧动稳定性及反应的奇异摄动理论

应用奇异摄动法分析横侧小扰动运动的动稳定性问题,将四阶问题分解为小根、大根和复根模态,它对应于经典理论中的螺旋、滚转和荷兰滚模态,并给出了动态反应过程的解。