一种提高螺栓联接强度的新方法

根据山本晃教授对螺栓，螺母，螺纹牙受力及其变形研究的成果，导出了该理论条件下受拉螺栓在等载荷受力状态下，当螺栓螺纹采用标准尺寸，螺母螺纹的螺旋线形状，并依据实用性，从螺母螺纹加工方便考虑，提出了近似等负荷螺纹。     

Heterogeneous solid/gas chemistry of organic compounds related to comets,meteorites, Titan,and Mars: Laboratory and in lower Earth orbit experiments

To understand the evolution of organic molecules involved in extraterrestrial environments and with exobiological implications, many experimental programs in the laboratory are devoted to photochemical studies in the gaseous phase as well as in the solid state. The validity of such studies and their applications to extraterrestrial environments can be questioned as long as experiments conducted in space conditions, with the full solar spectrum, especially in the short wavelength domain, have not been implemented. The experiments that are described here will be carried out on a FOTON capsule, using the BIOPAN facility, and on the International Space Station, using the EXPOSE facility. Vented and sealed exposition cells will be used, which will allow us to study the chemical evolution in the gaseous phase as well as heterogeneous processes, such as the degradation of solid compounds and the release of gaseous fragments.     

基于日地月信息的航天器全弧段自主容积卡尔曼滤波导航

高精度全弧段航天器自主导航是航天应用技术的发展方向,是实现航天器在轨任务执行的前提和基础。文章对仅利用日、地、月等天文信息进行航天器全弧段自主导航方法进行了研究。首先,以航天器轨道动力学方程和航天器与日地月之间的夹角信息及地心距作为自主导航系统的状态模型和观测模型,构建了非线性导航系统模型。其次,给出了全弧段自主导航算法,在日月可见弧段采用非线性容积卡尔曼滤波实现航天器自主导航,在星蚀时段利用航天器轨道动力学模型进行高精度轨道预报。最后,给出了数值仿真算例。结果表明,基于日地月天文信息的航天器全弧段自主导航精度保持在2km以内,能够满足其自主导航的要求。     

直尺反转组合法测量直线度的理论分析

对直尺反转组合法的测量原理进行了较为深入的理论分析，指出测量的准确性受测头误差、采样点定位误差、直尺尺面斜率、直尺再定位误差、直尺各点直线度误差的变化率等五个方面共同作用。其中，采样点定位误差和直尺安装斜率影响直线度测量准确度这一结论，将适用于其他的直尺直线度测量方法，因而具有普遍的指导意义。     

构架式可展开天线自由度与奇异性分析

针对以四面体为基本单元的构架式空间可展开天线,基于螺旋理论分析了多环耦合机构3RR-3RRR基本单元及多单元组网的自由度,降低分析此构架单元过约束与奇异性的复杂性。首先,根据螺旋理论能同时表示运动副轴线的位置和运动副类型的特点,建立了3RR-3RRR单元各铰链的运动螺旋并求解出单元过约束数;其次,运用修正的Kutzbach-Grübler公式求解出此单元的自由度,并分析出在特殊位形下的奇异性和瞬时性;最后,多单元组网成一个复杂耦合机构,采用等效构型的方法简化组网结构可得此天线反射器收展所需自由度,再通过计算各花盘的相对间距来验证构架可展开天线的收展协调性。研究表明构架式天线反射器3RR-3RRR四面体单元为单自由度机构且含有4个过约束,便于机构的展开控制,在同步杆铰链处于特殊位形下有约束奇异。组网后反射器桁架系统是单自由度机构,机构在单驱动运动过程中可展开完全,实现构架可展开天线各杆件在工作时运动协调,在空间机构领域具有良好的应用性。     

Reevaluation of thermosphere heating by auroral electrons

This paper presents a new calculation of neutral gas heating by precipitating auroral electrons. It is found that the heating rate of the neutral gas is significantly lower than previous determinations below 200 km altitude. The neutral gas heating arises from the many exothermic chemical reactions that take place from the ions and excited species created by the energetic electrons. The calculations show that less than half the energy initially deposited ends up heating the neutral gases. The rest is radiated or lost in the dissociation of O₂ because the O atoms do not recombine in the thermosphere. This paper also presents a new way of calculating the heating rate per ionization that can be used for efficient determination of the overall neutral gas heating for global thermosphere models. The heating rates are relatively insensitive to the neutral atmosphere when plotted against pressure rather than altitude coordinates. At high altitudes, the heating rates are sensitive to the thermal electron density and long-lived species. The calculations were performed with the Field Line Interhemispheric Plasma (FLIP) model using a 2-stream auroral electron precipitation model. The heating rate calculations in this paper differ from previous heating rate calculations in the treatment of backscattered electrons to produce better agreement with observed flux spectra. This paper shows that more realistic model auroral electron spectra can be obtained by reflecting the up going flux back to the ionosphere at the upper boundary of the model. In this case, the neutral gas heating rates are 20%–25% higher than when the backscattered flux escapes from the ionosphere.     

船舶仪表现场计量保障问题研究

分析了计量工作重要性和船舶仪表现场计量保障工作面临的问题，阐释了船舶论证研制阶段开展对船舶仪表现场计量保障的依据及论证设计思路，重点分析了国内船舶靠泊港口的环境条件,阐述了压力仪表原位测试的可行性、原位检测设计方案和实施效果。     

Unsteady drag measurements for flow over a circular disk

对垂直于来流方向的圆盘进行非定常测力实验,研究上游二维干扰圆杆和圆盘绕流雷诺数(雷诺数范围为0.44×10⁵~2.74×10⁵)对圆盘阻力及其脉动特性的影响.实验结果表明,无论有无上游干扰,圆盘平均阻力系数均不随雷诺数改变.上游干扰圆杆在降低圆盘阻力系数的同时,使圆盘阻力脉动量增大,而且当圆盘绕流雷诺数大于1.84×10⁵时阻力脉动量的增幅将随雷诺数的加大而迅速增加.对圆盘阻力的频谱分析表明,在圆盘上游无干扰时,圆盘绕流形成的螺旋状涡引起的非轴对称波动频率(斯特劳哈尔数为0.135)为阻力脉动的主频.     

塞式喷管性能损失分析

影响塞式喷管性能的因素是多方面的,为了明确各种损失对其的影响程度,根据塞式喷管的工作特点,通过建立的塞锥壁面压力分布的简化模型,初步分析了这些因素,比如摩擦损失、化学非平衡损失、截短损失和底部损失等.结果表明,由于塞锥长度的截短所引起的截短损失和底部损失是影响塞式喷管性能的主要因素.为了减小由此所带来的性能损失,应通过实验和数值模拟的方法着重研究气流在塞锥上和底部的流动特征,并且在设计的过程中应该考虑这些因素,以降低其对性能的影响.     

Generic procedure for designing and implementing plan management systems for space science missions operations

This paper is one of the components of a larger framework of activities whose purpose is to improve the performance and productivity of space mission systems, i.e. to increase both what can be achieved and the cost effectiveness of this achievement. Some of these activities introduced the concept of Functional Architecture Module (FAM); FAMs are basic blocks used to build the functional architecture of Plan Management Systems (PMS). They also highlighted the need to involve Science Operations Planning Expertise (SOPE) during the Mission Design Phase (MDP) in order to design and implement efficiently operation planning systems. We define SOPE as the expertise held by people who have both theoretical and practical experience in operations planning, in general, and in space science operations planning in particular. Using ESA’s methodology for studying and selecting science missions we also define the MDP as the combination of the Mission Assessment and Mission Definition Phases. However, there is no generic procedure on how to use FAMs efficiently and systematically, for each new mission, in order to analyse the cost and feasibility of new missions as well as to optimise the functional design of new PMS; the purpose of such a procedure is to build more rapidly and cheaply such PMS as well as to make the latter more reliable and cheaper to run. This is why the purpose of this paper is to provide an embryo of such a generic procedure and to show that the latter needs to be applied by people with SOPE during the MDP. The procedure described here proposes some initial guidelines to identify both the various possible high level functional scenarii, for a given set of possible requirements, and the information that needs to be associated with each scenario. It also introduces the concept of catalogue of generic functional scenarii of PMS for space science missions. The information associated with each catalogued scenarii will have been identified by the above procedure and will be relevant only for some specific mission requirements. In other words, each mission that shares the same type of requirements that lead to a list of specific catalogued scenarii can use this latter list of scenarii (regardless of whether the mission is a plasma, planetary, astronomy, etc. mission). The main advantages of such a catalogue are that it speeds-up the execution of the procedure and makes the latter more reliable. Ultimately, the information associated to each relevant scenario (from the catalogue or freshly generated by the procedure) will then be used by mission designers to make informed decisions, including the modification of the mission requirements, for any missions. In addition, to illustrate the use of such a procedure, the latter is applied to a case study, i.e. the Cross-Scale mission. One of the outcomes of this study is an initial set of generic functional scenarii. Finally, although border line with the above purpose of this paper, we also discuss multi-spacecraft specific issues and issues related to the on-board execution of the plan update system (PUS). In particular, we show that the operation planning cost of N spacecraft is not equal to N times the cost of 1 spacecraft and that on-board non-synchronised operation will not require inter-spacecraft communication. We also believe that on-board PUS should be made possible for all missions as a standard.