基于双基雷达原理的GNSS海面反射信号建模方法

全球导航卫星系统反射(GNSS-R)技术应用过程中接收机的测试验证需要反射信号产生源,以降低成本。信号的模型是GNSS-R信号产生源中的核心。针对缺乏相应模型的问题,提出了一种根据双基雷达原理建立GNSS海面反射信号模型的方法。首先,在分析GNSS海面反射信号特征的基础上,选取了恰当的海面反射点。然后,计算了雷达方程中的散射系数和散射面积,从而得到相应反射点的反射信号功率。最后,对所求得的反射信号参数进行仿真验证。验证的结果表明,反射信号的相关功率曲线与ZV模型理论曲线的相关系数优于0.98,能够有效地用于GNSS海面反射信号的生成。因此,该方法可为GNSS-R信号产生源的研制提供一定的理论支撑。     

机载GNSS海洋反射信号的建模与仿真

由于全球导航卫星系统反射(GNSS-R)机载试验耗费大和重复性差,需研制GNSS-R信号模拟器,但没有相应的反射信号模型。提出了一种基于数据拟合的机载GNSS海洋反射信号建模方法。首先,对复杂的GNSS海面反射信号进行近似简化。然后利用ZV模型生成的时延相关功率曲线,通过最小二乘拟合和非线性拟合,建立了多条等时延间隔的海洋反射信号功率衰减模型,从而得到机载GNSS海洋反射信号的时延、功率、多普勒频率参数。最后,对多条反射信号的合路信号进行相关的仿真验证。验证的结果表明模拟的14条反射信号的相关功率曲线与ZV模型理论曲线的相关系数优于0.99,能够有效地用于GNSS海洋反射信号的生成。该方法可根据海面风场、浪高、波高等海面信息,模拟不同海况的海洋反射信号,为GNSS-R信号模拟器的研制奠定基础。     

涌浪及降雨影响下的GNSS海面反射信号建模

全球导航卫星系统（GNSS）海面反射信号的模拟仿真采用的海浪谱多为风驱模型，而忽略了真实复杂环境中涌浪、降雨的影响。为此，提出了一种涌浪、降雨影响下的GNSS海面反射信号模型。首先，对Elfouhaily海浪谱、涌浪谱、降雨谱分别进行仿真，从海浪谱的角度分析涌浪、降雨对GNSS反射信号的影响。然后，设计了引入涌浪、降雨影响因子后的GNSS反射信号建模的方法，并建立噪声模型。最后，对星载场景下仿真得到的二维时延-多普勒相关功率分布图像（DDM）、时延相关功率波形（DW）进行分析，并与英国技术演示卫星（UK TDS-1）实测数据的处理结果进行了对比验证。结果表明:涌浪主要形成对GNSS反射信号影响较大的大尺度粗糙海面，而降雨对GNSS反射信号影响较小；仿真的DDM与实测数据结果的波形有很好的一致性，DW对比的相关系数达到0.92，优于未修正模型的对比结果，模拟的反射信号更为真实，证明了提出的GNSS反射信号建模方法的可行性、有效性。对真实复杂环境下的GNSS反射信号建模及GNSS反射信号星载探测应用研究具有一定的参考意义和实用价值。      

基于相关功率修正的地基GNSS-R土壤湿度反演

利用全球导航卫星系统反射信号测量技术(GNSS-R)进行土壤湿度反演过程中，实际接收天线方向性会造成GNSS直反信号相关功率测量偏差。针对地基观测场景下天线方向性造成的相关功率的类余弦振荡问题，提出了基于多项式拟合的信号相关功率修正方法。为了验证所提方法的有效性，开展了地基GNSS-R土壤湿度观测实验，结果表明:基于多项式拟合的相关功率修正可以消除信号相关功率的类余弦振荡，提升GNSS-R土壤湿度反演中的观测数据有效性和反演结果准确性。      

基于北斗卫星反射信号的海面溢油探测方法及试验

为了监测小规模固定海域的溢油状况,针对岸基接收平台提出了一种基于北斗卫星反射信号的海面溢油探测方法,该方法将全球导航卫星系统反射信号(GNSS-R)技术应用于岸基条件下的海面溢油探测。进行了岸基试验,利用右旋圆极化(RHCP)天线和左旋圆极化(LHCP)天线分别采集北斗卫星直射与反射信号,在信号同步的基础上提取卫星直射和反射信号的相关功率,并结合北斗卫星的高度角与方位角信息,反演目标海域的介电常数来判断海面有无溢油。试验结果表明探测表面为油面时,介电常数反演结果均值为3.6,标准差为2.13,这与油的真实介电常数范围2.0~4.5一致,远小于海水介电常数,证明将GNSS-R应用到岸基海面溢油探测中具有可行性。     

基于TechDemoSat-1卫星的GPS反射信号海面高度反演

针对星载GPS反射信号（GPS-R）海面测高的误差问题，基于星载GPS-R实测数据进行星载海面测高模型和误差修正模型的研究，并验证其有效性。利用TechDemoSat-1（TDS-1）数据，使用时延多普勒图（DDM）海面高度反演技术，着重分析了星载GPS-R海面高度反演中的各类误差，并建立了相应的误差模型。对星载GPS-R海面高度反演模型进行优化，采用DTU15全球平均海面模型、DTU全球海潮模型验证反演精度。结果证明:优化后反演模型得到的全球海面高度反演结果的平均绝对误差（MAD）为6.05 m，精度提高了约29%，有效提高了海面高度反演的精度。研究成果对于推广星载GNSS反射信号（GNSS-R）的海面测高应用具有一定的意义。      

星载GNSS-R海面风场观测载荷关键技术设计与验证

目前海面风场观测手段有限,基于全球导航卫星系统反射信号处理(global navigation satellite system reflection,GNSS-R)的天基观测为全球风场信息获取提供了全新的手段.GNSS-R海面风速探测技术具有全天时、全天候、低功耗、宽覆盖、多信号源、低成本等特点,日益获得了广泛的关注...     

直反信号协同的GNSS-R BSAR距离多普勒成像算法

针对目前基于全球导航卫星系统反射信号的双基地合成孔径雷达（GNSS-R BSAR)在一站固定模式下的大斜视,斜距历程复杂,回波信号方位空变导致回波信号难以处理的问题,提出改进的距离多普勒成像新算法。所提算法采用GNSS信号作为辐射源,根据一站固定模式下GNSS-R BSAR合成孔径时间长的特点,引入高阶等效斜视距离模型,得到导航卫星与目标斜距相对时间变化的精确描述。先通过直射信号与回波信号时域对消进行距离徙动校正,实现全场景目标距离徙动的精确校正;再通过方位向分块混合相关处理来克服回波信号方位向的移变性质,实现全场景高效精确成像。所提算法的成像效率优于传统后向投影时域（BP）算法,成像精度与BP算法相当,且可根据需要通过调整方位分块的宽度来提升聚焦效果。最后,用GPS-L5信号进行仿真和实验,仿真和实验结果验证了所提算法的可行性和高效性。     

Low Earth orbit constellation design using a multi-objective genetic algorithm for GNSS reflectometry missions

Spaceborne global navigation satellite system reflectometry (GNSS-R) is an innovative bistatic radar remote sensing technique utilizing low Earth orbit (LEO) based GNSS-R instruments to acquire GNSS L-band opportunistic signals for measuring geophysical parameters. A GNSS-R LEO constellation with an optimization design for its specialized missions is very significant and necessary. However, the constellation design involves multi-parameter and multi-objective optimization, and the classical analytic solution is not capable of such a complicated issue. This study proposes a multi-objective LEO constellation design method with a genetic algorithm (GA) and presents a framework for designing two GNSS-R LEO constellations, termed “lower-latitude constellation” for typhoons and hurricanes observation in the tropics and “global constellation” for global geophysical parameter measurements. Then, the observation capability of both designed constellations is evaluated in terms of the number of reflection points, spatial coverage density, and revisit time to verify the GA efficiency in LEO constellation design. Results show that the two designed LEO constellations with high fitness function values possess optimal orbit parameter set configuration and outperform the existing CyGNSS constellations in observation performance. Compared with CyGNSS, the number of reflection points observed by the lower-latitude constellation and the global constellation increases by 38% and 45%, as well as the spatial coverage density increases by 28% and 36%. The revisit time for the lower-latitude constellation is reduced by 0.29 h, whereas the revisit time for the global constellation increases by one hour.     

The impact on tsunami detection from space using GNSS-reflectometry when combining GPS with GLONASS and Galileo

The devastating Sumatra tsunami in 2004 demonstrated the need for a tsunami early warning system in the Indian Ocean. Such a system has been installed within the German-Indonesian Tsunami Early Warning System (GITEWS) project. Tsunamis are a global phenomenon and for global observations satellites are predestined. Within the GITEWS project a feasibility study on a future tsunami detection system from space has therefore been carried out. The Global Navigation Satellite System Reflectometry (GNSS-R) is an innovative way of using GNSS signals for remote sensing. It uses ocean reflected GNSS signals for sea surface altimetry. With a dedicated Low Earth Orbit (LEO) constellation of satellites equipped with GNSS-R receivers, densely spaced sea surface height measurements could be established to detect tsunamis. Some general considerations on the geometry between LEO and GNSS are made in this simulation study. It exemplary analyzes the detection performance of a GNSS-R constellation at 900 km altitude and 60° inclination angle when applied to the Sumatra tsunami as it occurred in 2004. GPS is assumed as signal source and the combination with GLONASS and Galileo signals is investigated. It can be demonstrated, that the combination of GPS and Galileo is advantageous for constellations with few satellites while the combination with GLONASS is preferable for constellations with many satellites. If all three GNSS are combined, the best detection performance can be expected for all scenarios considered. In this case an 18 satellite constellation will detect the Sumatra tsunami within 17 min with certainty, while it takes 53 min if only GPS is considered.     

Remote sensing using GNSS signals: Current status and future directions

The refracted, reflected and scattered signals of global navigation satellite systems (GNSS) have been successfully used to remotely sense the Earth’s surface and atmosphere. It has demonstrated its potential to sense the atmosphere and ionosphere, ocean, land surfaces (including soil moisture) and the cryosphere. These new measurements, although in need of refinement and further validation in many cases, can be used to complement existing techniques and sensors, e.g., radiosonde, ionosonde, radar altimetry and synthetic aperture radar (SAR). This paper presents the current status and new developments of remote sensing using GNSS signals as well as its future directions and applications. Some notable emerging applications include monitoring sea ice, dangerous sea states, ocean eddy and storm surges. With the further improvement of the next generation multi-frequency GNSS systems and receivers and new space-based instruments utilizing GNSS reflections and refractions, new scientific applications of GNSS are expected in various environment remote sensing fields in the near future.     

Deformation monitoring using GNSS-R technology

GNSS reflectometry (GNSS-R) has been widely studied in recent years for various applications, such as soil moisture monitoring, biomass analysis, and sea state monitoring. This paper presents the concept of a novel application of using GNSS-R technology for deformation monitoring. Instead of installing GNSS on the deformation body to sense the movement, GNSS-R deformation monitoring system estimates the deformation from receiving GNSS signal reflected by the deformation body remotely. A prototype of GNSS-R deformation monitoring system has been developed based on GNSS software receiver technology. A 3D geometrical model of GNSS signal reflection has been used to reveal the relationship between the change of carrier phase difference and deformation. After compensating the propagation path delay changes caused by satellite movement, the changes in the remaining carrier phase difference are linked to the deformation. Field tests have been carried using the GNSS-R system developed and the results show sub-centimeter level deformation can be observed with the new technology. Unlike other GNSS deformation monitoring methods, GNSS-R receivers are not installed on the slope which makes this new technology more attractive.