Development of the heat flow measurement system by the LUNAR-A penetrators

Lunar heat flow experiment is planned by using two LUNAR-A penetrators which will be deployed on the near-side and far-side of the lunar surface in 2000. Each penetrator has seven absolute and eleven relative temperature sensors. Impact experiments for real-size penetrator models onto a lunar-regolith analogue target confirmed that the sensors and electronics used in the Lunar-A Heat Flow Experiment can survive the shock loading expected during penetration of the penetrator in a lunar regolith. The calibration experiment demonstrates that the temperature sensors have a resolution of 0.01 degrees and that the thermal conductivity device have 10 % accuracy. In order to determine the heat flow value, we need a good thermal model and numerical simulation for the penetrator and the regolith which in turn requires accurate measurements of thermal properties of the penetrator's components. The current numerical models indicate that we will be able to obtain the lunar heat flow values within 20 to 30 percents in precision with this method.     

Upwards migration phenomenon on molten lunar regolith: New challenges and prospects for ISRU

As part of our research on the feasibility of producing commodities from lunar regolith by thermal-driven processes with minimal terrestrial precursors we need to characterize, reproduce, and understand thermophysical properties of the molten regolith still unforeseen under the lunar vacuum conditions at a scalable sample size. Two unanticipated phenomena, apparently caused by lunar melt’s surface tension under vacuum, have been revealed in our research work, vacuum void formation and upwards migration. In this paper we present our findings and thinkable explanation on the upwards migration phenomenon experimentally observed and consistently replicated as JSC-1A lunar regolith simulant melted at high vacuum. Upwards migration of molten lunar regolith will make future lunar ISRU’s melting processes both challenging as molten bulk material would migrate upwards along the container’s walls, and also promising on new opportunities for alternative ISRU’s sustainable processes as regolith’s upwards migration takes place in uniformed thin-film pattern. Among the potential ISRU’s processes that might use controlled thermal thin-film-based migration without the necessity of terrestrial precursors are production of feedstock for 3D printing, fractional separation of regolith’s component’s (O₂, metals, and alloys) via pyrolysis, film coating, purification of valuables solid crystals including silicon, and fabrication of key elements for microfluidic, and MEMS devices. Thermal upwards migration phenomenon on JSC-1A’s melt is formulated and explained by the authors as due to thermal Marangoni effect (also known as thermo-capillarity) in which temperature gradients within the melt’s bulk and along the crucible’s wall yield the surface tension large enough to supersede the gravitational force and yield the experimentally observed upwards thin-film migration. As far as the authors know, upwards thermal migration of molten JSC-1A (or other lunar simulant regolith) under vacuum has not been reported in the literature. A thermal mathematical model accounting for thermal Marangoni effect on molten JSC-1A agrees with what experimentally was observed, the formation of the meniscus on the melt-wall surface interface along with an incipient upwards migration in thin-film pattern along the crucible wall that, according to the model, experiences large temperature gradient, an important factor to trigger the thermal Marangoni effect along with the fact that surface tension of the molten lunar regolith material is temperature dependent.     

三层月壤模型的多通道微波辐射模拟与月壤厚度的反演

由月球表面数字高程试验性地构造了整个月球表面月壤厚度的分布.根据Clementine探月卫星的紫外-可见光光学数据,计算了整个月球表面月壤中FeO+TiO2含量分布,给出了整个月球表面月壤介电常数分布.由月球表层温度的观测结果以及月壤的导热特性,给出了月尘层与月壤层温度随纬度分布的经验公式.在这些条件的基础上,建立了月尘、月壤、月岩三层微波热辐射模型.由起伏逸散定理,模拟计算了该月球模型多通道辐射亮度温度.然后,以此辐射亮度温度模拟加随机噪声为理论观测值,按三层模型提出了月壤层厚度反演方法.由于高频通道穿透深度小,由高频通道的辐射亮度温度按照两层月尘-月壤微波热辐射模型反演月尘层与月壤层的物理温度,再由穿透深度较大的低频通道辐射亮度温度反演月壤层厚度.对于反演的相对误差也进行了讨论.      

Mechanical behavior of the metal parts welded with extraterrestrial regolith simulant by the solar concentrator in ISRU & ISRF application

The use of in-situ resources plays an important role on future extraterrestrial human activities for the facility repair and habitat construction, especially in sustainable space exploration of Moon and Mars. A method of the metal welded with extraterrestrial regolith simulant using solar processing under ambient conditions is presented. Metal parts are made of Q235B ferroalloy and TA2 titanium alloy into standard tensile members according to the ASTM code. They are disconnected from the middle in advance, and then welded together with lunar and Martian regolith simulant under ambient conditions, respectively. The entire welding process and precautions are detailed. Additionally, the mechanical behavior of weldments is characterized regarding their tensile strength. Furthermore, the fusion zone of weldments is studied by Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) measurements. The results show that it is possible to weld metal parts together with extraterrestrial regolith simulant by the solar concentrator. The average ultimate tensile strength of ferroalloy specimens welded with lunar and Martian regolith simulant is 2.94 MPa and 1.66 MPa; The average ultimate tensile strength of titanium alloy specimens welded with lunar and Martian regolith simulant is 4.95 MPa and 2.59 MPa. Moreover, the failure mode of all weldments was brittle failure. The welding joints strength derives from the phases that the regolith as the solder fusing into ferroalloys in a homogeneous way and titanium alloys in an inhomogeneous way. The presented method may provide a new thought for astronaut assistance associating with repairing and fabricating in subsequent Moon and Mars missions.     

月壤剖面冲击贯入式探测方案研究

以月壤剖面的原位探测为目标,提出一种利用土体结构侵彻原理的冲击式贯入器设计方案。重点阐述了冲击式贯入器的工作原理和机构实现方案,并开展多方案设计与分析。研制了原理样机并开展实验验证,证明利用冲击式贯入方法实现月壤剖面自动潜入的可行性,并对我国未来开展月壤剖面原位探测提出了相关建议。     

考虑热物性变化的月壤温度数值模拟

探月设备的热分析设计依赖于真实有效的月面热环境信息。借助于ANSYS热分析模块,建立了月壤导热系数随密度和温度变化、热容随温度变化的变热物性月壤温度求解模型,分别计算了月面纬度为26°和赤道地区的月表温度,探讨了赤道地区浅层月壤的温度分布。其中,月表温度计算结果与实测数据良好的一致性表明计算模型和所用计算参数适用可靠;而通过修正月壤导热系数来提高计算结果与实测数据的吻合程度则部分展示了月壤温度计算理论;在探讨赤道地区浅层月壤的温度分布时,文章给出了不同时刻对应的月壤温度剖面和热流剖面,并适度分析了月壤内部热流和导热系数对月壤温度剖面的影响,这些为利用月壤的温度剖面规律进行探月设备的热控设计提供了理论支持。     

Gas permeability and flow characterization of simulated lunar regolith

Recent discoveries of water ice trapped within lunar topsoil (regolith) have placed a new emphasis on the recovery and utilization of water for future space exploration. Upon heating the lunar ice to sublimation, the resulting water vapor could theoretically transmit through the lunar regolith, to be captured on the surface. As the permeability of lunar regolith is essential to this process, this paper seeks to experimentally determine the permeability and flow characteristics of various gas species through simulated lunar regolith (SLR). Two different types of SLR were compacted and placed into the permeability setup to measure the flow-rate of transmitted gas through the sample. Darcy’s permeability constant was calculated for each sample and gas combination, and flow characteristics were determined from the results. The results show that Darcy’s permeability constant varies with SLR compaction density, and identified no major difference in permeable flow between the several tested gas species. Between the two tested SLR types, JSC-1A was shown to be more permeable than NU-LHT under similar conditions. In addition, a transition zone was identified in the flow when the gas pressure differential across the sample was less than ∼40 kPa.     

Mapping lunar surface chemistry: New prospects with the Chandrayaan-2 Large Area Soft X-ray Spectrometer (CLASS)

Surface chemistry of airless bodies in the solar system can be derived from remote X-ray spectral measurements from an orbiting spacecraft. X-rays from planetary surfaces are excited primarily by solar X-rays. Several experiments in the past have used this technique of X-ray fluorescence for deriving abundances of the major rock forming elements. The Chandrayaan-2 orbiter carries an X-ray fluorescence experiment named CLASS that is designed based on results from its predecessor C1XS flown on Chandrayaan-1. We discuss the new aspects of lunar science that can be potentially achieved with CLASS.     

Moon surface radiation environment analysis for February 1956 solar event conditions

The radiation environment on the surface of the Moon presents a new source of particles resulting from the interaction of incoming solar protons and galactic cosmic rays with the lunar regolith. Here we present a study of the fluence profile of primary and secondary particles on the top 1 m layer of lunar regolith for the spectrum of one of the hardest spectrum solar event, that of February 1956. Different regolith compositions and their influence in proton and neutron production and backscattering is considered, as well as the nature of the backscattered radiation. Simple geometry Monte Carlo simulations have been used also for calculating regolith shielding properties, and it is shown that a layer of at least 50 cm regolith is needed for significantly reducing the dose levels received by astronauts in a hypothetical lunar habitat.     

Regolith effects in planetary X-ray fluorescence spectroscopy: Laboratory studies at 1.7–6.4 keV

Laboratory measurements are presented to study the effects of the physical properties of regolith on planetary soft X-ray fluorescence spectroscopy. Two laboratory setups are used to independently measure these regolith effects using lunar regolith analog samples with three different particle-size ranges. Discussion is given on the data analysis. Some of the data may be valid only for qualitative conclusions. Analytical modelling is used to separate the effects expected for a plane-parallel and homogeneous medium from those of measured regolith analogs. The surface roughness and porosity of the regolith are observed to induce an enhancement of the higher-energy part of the spectrum as a function of the incidence angle. The enhancement is larger for rougher surfaces. A brief discussion is given on the relevance of this study for future planetary missions carrying soft X-ray spectrometers.     

CAS-1 lunar soil simulant

Lunar soil simulant is a geochemical reproduction of lunar regolith, and is needed for lunar science and engineering researches. This paper describes a new lunar soil simulant, CAS-1, prepared by the Chinese Academy of Sciences, to support lunar orbiter, soft-landing mission and sample return missions of China’s Lunar Exploration Program, which is scheduled for 2004–2020. Such simulants should match the samples returned from the Moon, all collected from the lunar regolith rather than outcrops. The average mineral and chemical composition of lunar soil sample returned from the Apollo 14 mission, which landed on the Fra Mauro Formation, is chosen as the model for the CAS-1 simulant. Source material for this simulant was a low-Ti basaltic scoria dated at 1600 years from the late Quaternary volcanic area in the Changbai Mountains of northeast China. The main minerals of this rock are pyroxene, olivine, and minor plagioclase, and about 20–40% modal glass. The scoria was analyzed by XRF and found to be chemically similar to Apollo 14 lunar sample 14163. It was crushed in an impact mill with a resulting median particle size 85.9 μm, similar to Apollo soils. Bulk density, shear resistance, complex permittivity, and reflectance spectra were also similar to Apollo 14 soil. We conclude that CAS-1 is an ideal lunar soil simulant for science and engineering research of future lunar exploration program.     

考虑相互碰撞影响的月壤颗粒运动轨迹计算方法研究

针对登月着陆器下降过程扬起月壤颗粒的运动轨迹及空间分布问题, 提出了考虑月壤颗粒发生完全弹性碰撞和非完全弹性碰撞两种情况的月壤颗粒运动轨迹计算方法. 根据质量守恒和能量守恒定律确定月壤颗粒相互碰撞后的速度, 通过羽流场与月壤颗粒的流固耦合相互迭代计算方法, 获得被扬起的月壤颗粒在羽流场和相互碰撞共同作用下随时间的运动轨迹和空间分布. 基于美国Apollo 11登月过程实测数据, 采用数值模拟对该方法进行验证. 结果表明, 考虑月壤颗粒相互碰撞的影响后, 其运动规律出现较明显的扩散趋势. 进一步考虑月壤颗粒相互碰撞引起能量损失的影响后, 月壤颗粒的扩散趋势有所减弱, 并且扬起的高度随着恢复系数的减小而降低.      

A flow sheet for the conversion of lunar regolith using fluorine gas

This work reviews and expands upon the previous fluorination processes for in situ production of oxygen and silicon from lunar regolith. The process units were simulated and a flow sheet was developed to determine the product distribution and energy requirements. Our results show that 0.21 kg silicon and 0.32 kg oxygen can be produced per kg regolith processed with a total cooling duty of 17 MJ/kg regolith and electrical duty of 29 MJ/kg regolith. The payload mass required for the process is estimated as 16 kg/kg regolith processed per day.     

On the measurements of the moon’s infrared temperature and its relation to the phase angle

Radiometric measurements of the thermal radiation originating from the moon’s surface were obtained using an infrared detector operating at wavelengths between 8 and 14 μm. The measurements cover a full moon cycle. The variation of the moon’s temperature with the lunar phase angle was established. The lunar temperatures were 391 ± 2.0 K for the full moon, 240 ± 3.5 K for the first quarter, and 236 ± 3 K for the last quarter. For the rest of the phase angles, the lunar temperature varied between 170 and 380 K. Our results are comparable with those obtained previously at these phase angles. For the new moon phase, the obtained temperature was between 120 and 133 K. With the exception of the new moon phase, our measurements at all the phase angles were consistent with those obtained using Earth-based data and those obtained by the Diviner experiment and the Clementine spacecraft. At the new phase, our measurements were comparable with those obtained from the ground but were significantly higher than those obtained by the Diviner and Clementine data. We attribute this inconsistency to either the calibration curve of our detector, which does not perform well at very low temperatures, or to infrared emission from the atmosphere. A simple linear model to predict the lunar temperature as a function of the phase angle was proposed. The experimental errors that affect the measured temperatures are discussed.     

The lunar dust pendulum

An analytic model for the motion of a positively charged lunar dust grain in the presence of a shadowed crater at a negative potential in vacuum is presented. It is shown that the dust grain executes oscillatory trajectories, and an expression is derived for the period of oscillation. Simulations used to verify the analytic expression also show that because the trajectories are unstable, dust grains are either ejected from the crater’s vicinity or deposited into the crater forming “dust ponds.” The model also applies to other airless bodies in the solar system, such as asteroids, and predicts that under certain conditions, particularly near lunar sunset, oscillating dust “canopies” or “swarms” will form over negatively charged craters.     

模拟月壤铺粉过程DEM数值仿真

空基激光选区熔化（SLM）技术与原位资源利用（ISRU）概念结合，有望解决地外大规模基地建设的工程难题。SLM铺粉过程对成形件性能和质量有重要影响。基于非球形粒子叠加球模型方法，建立模拟月壤颗粒几何模型；基于线性弹簧-阻尼接触作用模型、Hamaker理论及牛顿运动定律，建立颗粒动力学模型；采用三维离散单元方法（DEM）及软球模型，进行不同工况下模拟月壤在铺粉过程中的流变特性研究。结果显示:所提模型和方法能开展指定工况和环境参数的模拟月壤颗粒系统流动性和堆积行为数值仿真研究；月面低重力环境导致粉床表面粗糙度变大、堆积密度和平均配位数变小；通过降低铺粉速度和优化刮刀型面，可以有效改善月基铺粉的粉床质量，获得更密实和均匀的粉床结构。      

基于球堆叠的月壤蓄热器传热特性数值研究

月壤蓄热是月球原位资源利用的一种重要方式，也是解决未来月球基地能源需求的最具潜力的途径之一。针对月壤蓄热过程，建立了基于球形堆叠的月壤蓄热器多孔介质蓄热模型。蓄热器的壳体采用登月舱下降级的燃料罐，流体传热介质采用氦气。通过数值模拟的方法研究了不同流动压降下月壤蓄热球堆叠方式、球直径对蓄热器传热过程的影响规律和机理，并分析了蓄热动态过程。研究结果表明，月壤蓄热球在简单立方体均匀堆叠（SC）和面中心立方体均匀堆叠(FCC)两种方式下，SC堆叠方式的综合蓄热指数比FCC模式可提高302%；同时还发现月壤蓄热球的直径存在最优值，可使得蓄热器在单位泵功下获得最大的蓄热量，并且该最佳值随着流体进出口压差增加而减小。该研究可为未来月壤蓄热器的设计和优化提供理论指导。     

Use of lunar regolith as a substrate for plant growth.

Regenerative Life Support Systems (RLSS) will be required to regenerate air, water, and wastes, and to produce food for human consumption during long-duration missions to the Moon and Mars. It may be possible to supplement some of the materials needed for a lunar RLSS from resources on the Moon. Natural materials at the lunar surface may be used for a variety of lunar RLSS needs, including (i) soils or solid-support substrates for plant growth, (ii) sources for extraction of essential, plant-growth nutrients, (iii) substrates for microbial populations in the degradation of wastes, (iv) sources of O2 and H2, which may be used to manufacture water, (v) feed stock materials for the synthesis of useful minerals (e.g., molecular sieves), and (vi) shielding materials surrounding the outpost structure to protect humans, plants, and microorganisms from harmful radiation. Use of indigenous lunar regolith as a terrestrial-like soil for plant growth could offer a solid support substrate, buffering capacity, nutrient source/storage/retention capabilities, and should be relatively easy to maintain. The lunar regolith could, with a suitable microbial population, play a role in waste renovation; much like terrestrial waste application directly on soils. Issues associated with potentially toxic elements, pH, nutrient availability, air and fluid movement parameters, and cation exchange capacity of lunar regolith need to be addressed before lunar materials can be used effectively as soils for plant growth.     

铲挖式表层月壤采样器设计与试验

针对月球表层土壤的采样任务,设计了一种搭载于机械臂末端的采样器。基于离散元手段,利用Scott真实月壤微型三轴压缩试验数据,完成仿真散体颗粒特性参数匹配,开展了采样器铲取、挖取采样过程的仿真分析,获得作业过程采样器的动力学特性。此外,开发了采样器性能测试系统,针对不同模拟月壤对象进行了采样试验,测试获得了采样器采样能力随深度及月壤硬度的变化情况,得到采样器操作参数的可行区域。采样器能够实现铲取、挖取和封装容器转移多重任务,研究工作为中国未来的月面采样任务提供方案借鉴和技术支撑。     

Modifications of Martian ice-saturated regolith due to meteoroid impact

The possibility of water ice in the Martian subsurface regolith continues to present an intriguing enigma. We submit that any exo-martian source of energy, i.e. meteorite, asteroid or cometary impact, must disturb the equilibrium within the regolith surrounding an impact site. We farther propose impactors with the size range of 100 m and larger with velocities of 10 km s⁻¹ are effective in causing significant temperature increases in the regolith and subsequent ice melting. We present our studies of the crater formation within Martian surface layers that presumably are a solid mixture of regolith and water ice. Mass ratio of rocks to ice, as well as the thermal gradient in the crust, are the parameters. We have completed numerical simulations of a cratering event by means of two-dimensional, axialsymmetric hydrocodes involving a free particles' method in order to provide a simulation of an impact cratering. A fraction of subsurface ice melts and the crater partially forms from mud-like material. Comparison of a calculated crater and observed Martian crater is presented. The simplified analytical estimates concerning melting of ground ice in the regolith surrounding a Martian impact crater are presented.