北斗卫星导航系统空间信号用户测距误差计算方法研究

按照空间信号用户测距误差（UserRangeError,URE）定义,参考GPS标准定位服务性能规范中URE的计算方法,结合北斗卫星导航系统（BDS）多星混合星座类型,在考虑仰角限制情况下,详细推导了适用于BDS的瞬时URE和均方根URE计算公式。利用广播星历和精密星历计算的卫星轨道误差和卫星钟钟差,带入所推导的公式,对BDSURE进行分析评估;并使用GNSS接收机原始观测量和伪距观测方程计算BDSURE,最后将两种计算结果进行对比分析。研究结果表明,两种方法BDSURE的计算结果基本一致,在95%置信度情况下均小于2.5m,满足北斗公开服务性能规范中对空间信号URE的基本要求。     

北斗三号系统广域差分服务精度评估

为了保证北斗系统广域差分服务的平稳过渡，北斗三号系统（BDS-3）通过GEO卫星B1I/B3I信号播发北斗二号协议广域差分改正信息，包括等效钟差改正数与格网点电离层信息。分析了增加BDS-3卫星后，等效钟差改正数和格网点电离层信息的特征，并对BDS-2和BDS-3的用户差分距离误差（UDRE）进行了对比。联合BDS-2和BDS-3实测数据，对BDS-3广域差分服务定位精度进行了评估。分析结果表明:BDS-2卫星广播星历空间信号用户等效距离误差（UERE）约为1 m，经过等效钟差改正数后，用户差分距离误差约为0.3 m；BDS-3卫星广播星历空间信号用户等效距离误差约为0.4 m，经过等效钟差改正数后，用户差分距离误差约为0.2 m。等效钟差改正数可以修正广播电文更新带来的空间信号阶跃误差，显著提升卫星空间信号精度。与基本导航系统播发的Klobuchar 8模型，广域差分系统所播发的格网点电离层信息可将电离层误差修正精度提高约18%。与单独BDS-2卫星相比，BDS-2/BDS-3卫星联合条件下，基本导航的单频用户和双频用户定位精度可分别提升26%和41%；广域差分服务的单频用户定位精度为2.4 m，双频用户定位精度为1.7 m，单频用户和双频用户定位精度分别提升13%和41%。      

北斗区域Klobuchar改进模型及其修正精度分析

北斗卫星导航系统采用Klobuchar模型修正单频接收机用户的电离层延迟误差,由于此模型从亚洲地区应用角度考虑,在某一特定区域的修正精度甚至不足50%。为进一步提高区域电离层延迟修正精度,提出在原模型8个改正参数的基础上增加5个关键参数的Klobuchar改进模型,并采用松弛迭代与直线搜索法中的黄金分割相结合的算法对新增参数进行求解。以天津及其附近区域为例,利用GPStation6接收机采集到的实测数据对改进模型与原模型进行计算。将国际全球导航卫星系统服务组织（International GNSS Service,IGS）发布的全球电离层格网数据作为参考值,对比分析改进模型与原模型的修正精度。结果表明,区域Klobuchar改进模型在天津及其附近区域的电离层延迟平均修正精度比原模型提升了10.46%,平均修正精度达到77.51%。     

北斗星基增强系统性能评估

以实际广播星历、精密星历和北斗星基增强系统(BDSBAS)增强报文为实验数据，通过计算BDSBAS轨道误差、卫星钟差、空间信号测距误差和BDSBAS格网电离层有效点、播发时间和电离层延迟误差6个指标，评估分析了BDSBAS空间信号的性能。结果显示：BDSBAS增强后的GPS卫星轨道误差在切向、法向、径向分别降低了34.57%,40.57%,30.90%；卫星钟差均方根降低了24.31%，卫星钟差标准差降低了16.8%；空间信号测距误差相比增强前降低了32.75%;BDSBAS格网电离层有效点覆盖了中国及周边地区；BDSBAS各点电离层延迟播发间隔均达到ICAO对精确差分定位的要求；电离层延迟在0°-5°N范围内误差在0.4 m以上，可信度均达到99.9%，在5°-55°N范围内误差小于0.4 m，可信度均为100%;BDSBAS水平定位误差提升超过25%，垂直定位误差提升超过50%，完好性均在99.9%以上。     

北斗首颗备份卫星性能初步分析

主要从卫星钟差预报、轨道测定精度、伪距波动情况等角度分析了I6卫星与北斗卫星导航系统（BDS）其他现役倾斜地球同步轨道（IGSO）卫星的异同,并从位置精度因子（PDOP）和格网可用性评估了I6卫星入网对BDS的贡献。利用星地双向时频传递设备观测的星地钟差数据,评估了I6卫星星载原子钟的预报性能,结果表明,I6卫星发播的卫星钟参数外推5h预报误差的均方根误差（RMS）为232ns,外推1h预报误差的RMS为073ns,与现役IGSO卫星钟差预报水平相当;对多星联合精密定轨结果分析表明,与北斗现役I3卫星相比,姿态控制方式优化后的I6卫星在地影期间的轨道精度并未发生明显衰减,克服了现有北斗二号卫星在地影期间轨道精度下降,从而影响北斗服务的连续性、可用性问题;利用大口径抛物面天线采集到的数据对I6卫星的伪距波动进行了分析,结果表明I6卫星单个观测弧段内其伪距波动峰峰差约为1m,与其他IGSO卫星一致;进行PDOP仿真计算,结果表明I6卫星的加入使得喀什地区的PDOP最大值由1282下降为726,PDOP大于6的时段所占百分比由2911%下降为1721%;对格网电离层产品实施解算,结果表明I6卫星的加入使得6个电离层格网点的可用度提升至95%以上。     

基于北斗GEO卫星双频观测值连续监测电离层延迟

利用北斗GEO卫星观测数据直接计算电离层延迟。由于GEO卫星具有固定穿刺点和静地的特性,使得观测站监测电离层变化时可不考虑空间变化,并可进行连续不间断监测。通过分析北斗GEO卫星三种频率码伪距和载波相位观测值不同组合,选取B1&B2双频计算电离层延迟为最优组合,采用相位平滑伪距的方法计算电离层延迟TEC,相较其他电离层模型,该方法的优点是不会引入模型误差,可得到连续的高精度的电离层延迟监测结果。     

基于NTCM-BC模型的全球卫星导航系统单频电离层延迟修正

选择NTCM-BC模型作为单频电离层延迟修正模型,通过非线性最小二乘拟合的方法,利用提前一天预测的电离层图（COPG文件）,计算得到NTCM-BC模型修正系数;利用Klobuchar模型和IGS发布的GIM数据对NTCM-BC模型进行比较和分析.对太阳活动高、中、低年实测数据的分析结果表明:全球平均水平上,NTCM-BC模型的电离层延迟修正性能明显优于Klobuchar模型,NTCM-BC模型的TEC平均误差和均方根误差比Klobuchar模型分别下降了41%和30%;模型的TEC计算误差与太阳活动剧烈程度成正相关,即太阳活动高年模型误差较大,太阳活动低年误差相对较低.相较于磁静日,磁扰日期间Klobuchar模型和NCTM模型的误差均有一定程度的增加.此外,模型的电离层修正误差同时存在明显的纬度、季节和地方时差异.      

WAAS系统中电离层折射校正的新方法及计算结果

电离层介质的色散性是影响电磁波信号进行卫星导航定位精度的重要因素之一.配合北斗二代分系绩研制任务,提出了一种新的电离层折射校正算法,并利用2000年7月1日到3日的双频GPS观测数据对6个用户站进行试算,进一步将试算所得均方根误差和电离层网格算法得到的误差进行比较.结果表明,对于中纬区域的用户站,估算的TEC误差约为0.5 m左右;而低纬用户误差相对增大,为1 m左右.文中给出的算法与电离层网格模型所提供的精度相差不多,在未来中国自主的卫星增强系统中采用新方法进行电离层进行修正是可行的及有效的.      

北斗D2导航电文解析和完好性性能分析

为评估北斗D2导航电文对系统空间信号完好性影响，对D2导航电文结构和内容进行研究。首先，通过基本导航信息的解析，给出了确定卫星位置和用户位置过程所需的信息和时间，并对受卫星星历和时钟影响的用户测距误差做了说明，介绍了电离层误差、对流层误差改正模型。然后，通过增强服务信息的解析，论述了完好性信息（RURA、UDRE）及格网电离层延迟的计算方法。最后给出了使用完好性信息、用户局部误差获取用户定位误差保护级的算法。     

Kalman滤波估算电离层延迟的一种优化方法

频间偏差（Inter Frequency Bias，IFB）通常会给电离层延迟的解算带来误差.目前从电离层延迟中消除频间偏差的方法是基于GPS双频观测数据建立垂直电离层模型，利用卡尔曼滤波实时估算电离层模型系数和频间偏差.然而滤波过程中的测量噪声协方差矩阵没有考虑系统观测量之间的相关性，这会导致滤波模型不准确，进而影响最后求解的电离层延迟的准确性.本文选取了美国19个参考站的GPS双频观测数据，利用卡尔曼滤波实时估算电离层模型系数以及频间偏差.在滤波过程中，通过将先验频间偏差的估计方差引入测量噪声方差，实现对测量噪声协方差矩阵的优化.计算结果表明，优化后得到的卫星频间偏差与欧洲定轨中心（Center for Orbit Determination in Europe，CODE）得到的频间偏差更接近.将优化后的电离层延迟代入伪距解算，得到的位置误差的标准差在东向和天顶向分别下降了12.5%和15.4%，天顶向误差平均值下降了17.6%，定位精度得到提高.      

Beidou wide-area augmentation system clock error correction and performance verification

On December 27, 2018, the Beidou-3 System (BDS-3) has completed the deployment of 18 Medium Earth Orbit (MEO) satellites combined as a space constellation. In addition to the augmentation information for the new system signals B1C and B2a, the BDS-3 is compatible with the three augmentation information broadcast by the BDS-2 system for B1I and B3I signals: equivalent clock error correction, User Differential Ranging Error (UDRE) and Grid Ionosphere Vertical Error (GIVE). In this paper, the observation data of Beidou monitoring network are used to analyze the pseudo-range observation quality of the smooth transition signals B1I and B3I of BDS-2 and BDS-3. At the same time, the relationship between the equivalent clock error correction and the prediction error of the satellite clock is analyzed by using the Two-Way Satellite Time and Frequency Transfer (TWSTFT) data. The results show that the correlation between the equivalent clock error correction and the monitored clock error by using the TWSTFT data is greater than 60%. We calculate the UDRE by using the equivalent clock error correction. The results show that the satellite equivalent clock error correction can improve the accuracy of User Equivalent Range Error (UERE) by about 50%. This paper also compares the positioning accuracy of the BDS-2 satellites with the BDS-2 satellites combined BDS-3 satellites. The results show that the three-dimensional positioning accuracy is improved by about 30% after the BDS-3 satellites are added.     

Analysis of BDS-3 distributed autonomous navigation based on BeiDou system simulation platform

Satellite autonomous navigation is an important function of the BeiDou-3 navigation System (BDS-3). Satellite autonomous navigation means that the navigation satellite uses long-term forecast ephemeris and Inter-Satellite Link (ISL) measurements to determinate its own spatial position and time reference without the support of the ground Operation and Control System (OCS) for a long time to ensure that the navigation system can normally maintain the time and space reference. This paper aims to analyze the feasibility of distributed autonomous navigation algorithms. For the first time, a ground parallel autonomous navigation test system (GPANTS) is built. The performance of distributed autonomous navigation is then analyzed using the two-way ISL ranging of BDS-3 satellites. First, the BDS simulation platform and the GPANTS are introduced. Then, the basic principles of distributed satellite autonomous orbit determination and time synchronization based on ISL measurements are summarized. Preliminary evaluation of the performance of the BDS-3 constellation autonomous navigation service under ideal conditions through simulation data. Then the performance of autonomous navigation for 22 BeiDou-3 satellites using ISL measurements is evaluated. The results show that when satellites operate autonomously for 50 days without the support of any ground station, the User Range Error (URE) of autonomous orbit determination is better than 3 m, and the time synchronization accuracy is better than 4 ns.     

风云三号C星GNOS北斗掩星电离层探测初步结果

利用风云三号卫星C星GNOS掩星探测仪电离层数据,分析了2013年10月FY-3C GNOS探测的北斗掩星电离层廓线分布,将2013年10月1日至2015年10月10日期间FY-3C GNOS观测的F₂层峰值电子密度（N_mF₂）与地面电离层测高仪观测结果进行对比,验证了FY-3C GNOS北斗电离层掩星的探测精度.结果表明,FY3-C GNOS北斗电离层掩星与电离层测高仪探测的N_mF₂数据相关系数为0.96,平均偏差为10.21%,标准差为19.61%.在不同情况下其数据精度有如下特征:白天精度高于夜晚;夏季精度高于分季,分季精度高于冬季;中纬地区精度高于低纬地区,低纬地区精度高于高纬地区; BDS倾斜同步轨道（IGSO）卫星精度高于同步轨道（GEO）卫星和中轨道（MEO）卫星.FY-3C GNOS北斗电离层掩星与国际上其他掩星电离层数据精度的一致性对GNSS掩星探测资料的综合利用具有重大意义.      

Analysis on navigation accuracy of high orbit spacecraft based on BDS GEO and IGSO satellites

To make up for the insufficiency of earth-based TT&C systems, the use of GNSS technology for high-orbit spacecraft navigation and orbit determination has become a new technology. It is of great value to applying Geosynchronous Earth Orbit (GEO) and Inclined GeoStationary Orbit (IGSO) navigation satellites for supporting the navigation of high-orbit spacecraft since there are three different types of navigation satellites in BeiDou Navigation Satellite System (BDS): Medium Earth Orbit (MEO), GEO and IGSO. This paper conducts simulation experiments based on Two-Line Orbital Element (TLE) data to analyze and demonstrate the role of these satellites in the navigation of high-orbit spacecraft. Firstly, the spacecraft in GEO was used as the target satellite to conduct navigation experiments. Experiments show that for the spacecraft on the GEO orbit, after adding GEO and IGSO respectively on the basis of receiving MEO navigation satellite signals, the accuracies were improved by 7.22 % and 6.06 % respectively. When adding both GEO and IGSO navigation satellites at the same time, the accuracy can reach 16 m. In the second place, navigation and positioning experiments were carried out on three high elliptical orbit (HEO) satellites with different semimajor axis (32037.2 km, 42385.9 km, 67509.6 km). The experiments show that the number of visible satellites has been improved significantly after adding GEO and IGSO navigation satellites at the same time. The visible satellites in these three orbits were improved by 32.84 %, 41.12 % and 37.68 %, respectively compared with only observing MEO satellites.The RMS values of the navigation positioning errors of these three orbits are 25.59 m, 87.58 m and 712.48 m, respectively.     

LEO enhanced Global Navigation Satellite System (LeGNSS) for real-time precise positioning services

Global Navigation Satellite System (GNSS) has been widely used in many geosciences areas with its Positioning, Navigation and Timing (PNT) service. However, GNSS still has its own bottleneck, such as the long initialization period of Precise Point Positioning (PPP) without dense reference network. Recently, the concept of PNTRC (Positioning, Navigation, Timing, Remote sensing and Communication) has been put forward, where Low Earth Orbit (LEO) satellite constellations are recruited to fulfill diverse missions. In navigation aspect, a number of selected LEO satellites can be equipped with a transmitter to transmit similar navigation signals to ground users, so that they can serve as GNSS satellites but with much faster geometric change to enhance GNSS capability, which is named as LEO constellation enhanced GNSS (LeGNSS). As a result, the initialization time of PPP is expected to be shortened to the level of a few minutes or even seconds depending on the number of the LEO satellites involved. In this article, we simulate all the relevant data from June 8th to 14th, 2014 and investigate the feasibility of LeGNSS with the concentration on the key issues in the whole data processing for providing real-time PPP service based on a system configuration with fourteen satellites of BeiDou Navigation Satellite System (BDS), twenty-four satellites of the Global Positioning System (GPS), and sixty-six satellites of the Iridium satellite constellations. At the server-end, Precise Orbit Determination (POD) and Precise Clock Estimation (PCE) with various operational modes are investigated using simulated observations. It is found out that GNSS POD with partial LEO satellites is the most practical mode of LeGNSS operation. At the user-end, the Geometry Dilution Of Precision (GDOP) and Signal-In-Space Ranging Error (SISRE) are calculated and assessed for different positioning schemes in order to demonstrate the performance of LeGNSS. Centimeter level SISRE can be achieved for LeGNSS.     

利用北斗观测数据实时监测中国区域电离层变化

北斗卫星导航信号采用三个频点工作,可以利用伪距双频组差方法解算电离层电子含量,为实时监视中国区域电离层变化提供新的技术手段.中国中低纬度处于电离层赤道异常变化区,在北纬20°±5°区域时常发生较大梯度的电离层变化.利用北斗实时多频伪距和相位观测数据,采用相位平滑伪距方法计算电离层穿刺点电子含量,分析通过北斗系统GEO卫星监测的电离层周日变化特性;采用多面函数方法拟合中国区域1°×1°分辨率的电离层延迟量,每5min绘制一幅中国区域电离层图,观测区域所有电离层穿刺点拟合残差RMS为2.778TECU;分析北斗系统实时监测中国区域电离层异常情况,当发生电离层异常变化时,相邻两天的VTEC（Vertical Total Electronic Content）峰值相差约60TECU.      

Correction model of BDS satellite-induced code bias and its impact on precise point positioning

There are code biases on the pseudo-range observations of the Beidou Navigation Satellite System (BDS) that range in size from several decimeters to larger than one meter. These biases can be divided into two categories, which are the code biases in the pseudo-range observations of Inclined Geo-Synchronous Orbit (IGSO) satellites and Medium Earth Orbit (MEO) satellites and the code biases in the pseudo-range observations of Geosynchronous Earth Orbit (GEO) satellites. In view of the code bias of the IGSO/MEO satellites, the code bias correction model is established using the weighted least square curve fitting method. After the correction, the code biases of the IGSO and MEO satellites are clearly mitigated. A methodology of correcting GEO code bias is proposed based on the empirical mode decomposition (EMD)-wavelet transform (WT) coupled model. The accuracies of the GEO multipath combination of the B1, B2 and B3 frequencies are improved by 39.9%, 17.9%, and 29.4%, respectively. Based on the corrections above, the ten days observations of three Multi-GNSS Experiment (MGEX) stations are processed. The results indicate that the convergence time of the precise point positioning (PPP) can be improved remarkably by applying a code bias. The mean convergence time can be improved by 14.67% after the IGSO/MEO code bias correction. By applying the GEO code bias, the mean convergence time can be further improved by 17.42%.     

基于单站CCD漂移扫描光电设备的同步轨道目标测定轨

地基光电观测在同步轨道目标监测领域具有重要作用.为评估单站光电设备对同步轨道目标的实际测定轨能力,利用上海天文台佘山站1.56m望远镜,采用CCD漂移扫描光电技术,对3颗北斗同步卫星开展试验观测,基于卫星精密星历评估目标的测定轨外符精度.结果表明:同步轨道目标的天文定位在方位和俯仰方向上的外符精度均好于0.3";在单圈次观测情况下,尽管轨道预报精度较低,约为数千米量级,但是观测弧段内定轨精度可优于百米;在多圈次观测情况下,轨道改进效果显著,定轨精度优于50m,外推至4d的轨道预报精度为百米量级.此外,定量评估了每晚不同观测时间跨度下同步轨道目标的测定轨精度,为单站光电设备实际应用提供了参考.