共查询到20条相似文献,搜索用时 718 毫秒
1.
为了提高脉冲爆震燃气的能量转换效率,分析了脉冲爆震燃气在涡轮内的膨胀过程,建立了评价爆震燃气能量转换难易度计算方法,并基于脉冲爆震燃烧室与轴流涡轮匹配工作数值模型,采用涡轮效率对燃气能量转换难易度计算方法进行了验证,结果表明: ①爆震波膨胀过程,爆震燃气在涡轮静叶内会产生热壅塞现象,并往上游形成前传压缩波; ②涡轮内爆震燃气的膨胀主要分一次膨胀、过度膨胀和二次膨胀三个阶段,爆震燃气在涡轮内的焓降主要发生在一次膨胀和二次膨胀阶段,在过度膨胀阶段,燃气在涡轮内做负功; ③当量比为0.72、0.89和1.00三种计算工况的燃气能量转换难易度分别为0.396、1.000和0.803,对应的涡轮效率分别为0.473 6、0.597 2和0.570 3,验证了燃气能量转换难易度计算方法的准确性。 相似文献
2.
3.
以光学滤光片薄膜边缘应力作为对象,研究了Ge/Zn S单、多层光学薄膜应力的变化规律。通过实验研究了离子束轰击能量以及真空退火温度等因素对Ge/Zn S光学薄膜应力类型、大小、变化及其分布的影响规律。Zn S薄膜的应力为压应力,采用离子束辅助工艺后薄膜边缘应力变得均匀;真空退火使Zn S薄膜的应力减小为原来的一半。通过优化沉积参数和张应力、压应力薄膜的组合降低了Ge/Zn S多层光学薄膜的应力,结果表明其平均应力分别为0.1 MPa,而且处于压应力状态。 相似文献
4.
5.
为分析旋转爆震喷管内非定常流动特性,本文基于特征线方法和旋转爆震燃烧室出口时均参数设计了一种塞式喷管模型,通过改变塞锥式喷管的进出口压比(压比分别为15、30和45),分析了喷管内非定常流场结构与喷管工作性能之间的相互关系,并探究了喷管进出口压比变化对喷管工作性能的影响。研究结果表明:旋转爆震燃烧室下游斜激波进入喷管后,在喷管内形成一道绕喷管壁面螺旋分布的激波,激波结构主要由波前气流角和激波前气流速度决定;爆震喷管局部工作状态依据相对螺旋激波位置分别存在自由膨胀状态、欠膨胀状态、欠膨胀与过膨胀过渡状态以及过膨胀状态四种情况,喷管处于第二种工作状态(欠膨胀)时,喷管内存在激波,并随着激波的传播不断增强,在第四种工作状态达到最大(喷管处于过膨胀状态),且喷管在第二到第四种工作状态内工作性能变差;在低压比(压比15)工作条件下喷管性能优于高压比(压比30),其最佳推力和燃料比冲分别为992.05N和1769.52s,因而旋转爆震喷管设计应选择较高的进出口压比作为设计点,使旋转爆震喷管更多的工作在低压比工作状态,以提高旋转爆震喷管工作效率。 相似文献
6.
7.
通过仿真研究了跨声速飞行状态下(Ma=1.2)一种带间隔式进气门的引射喷管流动特性,获得了二次流对三次流流动状态、喷管流动结构以及推力性能的影响规律。结果表明:带有间隔式辅助进气门的引射喷管内部存在显著的横向流动,诱导产生了多对流向涡结构,沿着流动方向流向涡的尺度逐渐减小。主流始终处于过膨胀状态,主导了引射喷管的内流流动,并和二次流之间形成了一道剪切层结构。随着二次流落压比的升高,二次流和三次流流量增加,其对主流的束缚作用增强,主流过膨胀现象得到有效抑制,推力性能从0.698增加至0.819。 相似文献
8.
9.
10.
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献