基于T-S模糊模型的非线性分布参数系统极点配置P-sD控制CSCD

采用Lyapunov直接法讨论分布参数系统的稳定性,建立分布参数系统的Lyapunov函数。为保证分布参数系统稳定,应使Lyapunov函数对时间的微分小于0。由于分布参数系统中存在空间一次微分项与二次微分项,Lyapunov函数对时间的微分中将出现常数项与积分项,针对常数项,引入空间一次微分项来抵消;针对积分项,引入对应的状态反馈来使系统稳定。利用边界条件量化Lyapunov函数对时间的微分中的各项,从而设计控制器,这是一种新的设计P-sD状态控制的方式。其中状态反馈的部分采用极点配置的方法来设计,当分布参数系统中出现状态变量的非线性函数时,采用T-S模糊模型表达,可以通过状态变量的线性组合精确描述非线性项,以便极点配置设计状态反馈。针对两个非线性分布参数数学模型进行仿真,结果证明设计的P-sD状态控制器可以使分布参数系统稳定,并达到期望的效果。     

Control of nearly singular decoupling systems and nonlinearaircraft maneuver

The author treats the question of control of a class of nonlinear systems using state variable feedback whose input/output map is nearly singular. Although the existing decoupling theory is applicable to such systems, this requires a large amount of control, which may not be permissible. A decoupling approach using state variable feedback in an approximate sense, but requiring a small control magnitude is considered. A decoupling scheme is presented that gives rise to a singularly perturbed system describing the fast dynamics of the control vector. The quasi-steady-state solution of the system gives a control law that decouples the system in an approximate way. The controller includes a servocompensator and a reference trajectory generator. Based on this result, a control law for approximate decoupling of roll angle, angle of attack, and sideslip in rapid, nonlinear airplane maneuvers is derived. Simulated responses of the closed-loop system show that large, simultaneous lateral and longitudinal maneuvers can be accurately performed in spite of uncertainty in stability derivatives     

Nonlinear Optimal Feedback Regulation of Satellite Angular Monenta

Some important regulation properties of satellite angular momentum dynamics are investigated using a combination of reaction jets and flywheels. The optimal feedback controller is designed in such a way that system regulation, under large perturbations, to a proper bounded subset in Rn, is achieved by using reaction jets. Thereafter, flywheels are activated to bring the system to the rest (desired) state. The domain and the size over which reaction jets are active, as well as the corresponding fuel cost, are discussed. Further, the effect of linear as well as nonlinear optimal feedback regulators on system behavior is indicated. Finally, the range (in the state space Rn) over which the flywheels are capable of regulating the system is also studied.     

具有指定闭环极点的最优控制系统鲁棒稳定摄动界

对线性二次最优控制系统,给出了选择适当加权矩阵从而保证系统具有希望闭环极点的方法。加权矩阵可以通过与期望极点有关的变换阵来调节,使得系统具有希望的动态品质。针对这种闭环系统存在不确定扰动时,得出了保证系统稳定的不确定摄动界     

无人机机动轨迹跟踪系统设计

对无人机机动飞行轨迹跟踪系统的内环姿态控制律和外环轨迹跟踪控制律两部分分别进行了设计。利用非线性动态逆方法设计了内环姿态控制律。外环轨迹跟踪控制律采用逆动力学前馈加模糊反馈的控制结构,提高系统对飞行条件及期望轨迹剧烈变化时的跟踪精度。仿真结果表明,所设计的系统能够控制无人机精确跟踪指定的机动轨迹,且相对于固定增益系统具有更好的鲁棒性。     

Nonlinear adaptive and sliding mode flight path control of F/A-18 model

The question of inertial trajectory control of aircraft in the three-dimensional space is discussed. It is assumed that the nonlinear aircraft model has uncertain aerodynamic derivatives. The control system is decomposed into a variable structure outer loop and an adaptive inner loop. The outer-loop feedback control system accomplishes (x,y,z) position trajectory and sideslip angle control using the derivative of thrust and three angular velocity components (p,q,r) as virtual control inputs. Then an adaptive inner feedback loop is designed, which produces the desired angular rotations of aircraft using aileron, elevator, and rudder control surfaces to complete the maneuver. Simplification in the inner-loop design is obtained based on a two-time scale (singular perturbation) design approach by ignoring the derivative of the virtual angular velocity vector, which is a function of slow variables. These results are applied to a simplified F/A-18 model. Simulation results are presented which show that in the closed-loop system asymptotic trajectory control is accomplished in spite of uncertainties in the model at different flight conditions.     

IFSTA输出响应反馈法的极点配置

介绍空中飞行模拟试验机变稳纵向控制系统输出响应反馈法的极点配置，该方法可处理单输入一多输出系统中反馈量的个数小于方程阶数的极点配置问题，理论与实践表明：该方法在应用到单变量控制的变稳纵向控制系统中的极点配置时，具有足够高的精度。     

A systematic method of smooth switching LPV controllers design for a morphing aircraft

This paper is concerned with a systematic method of smooth switching linear parametervarying(LPV) controllers design for a morphing aircraft with a variable wing sweep angle. The morphing aircraft is modeled as an LPV system, whose scheduling parameter is the variation rate of the wing sweep angle. By dividing the scheduling parameter set into subsets with overlaps, output feedback controllers which consider smooth switching are designed and the controllers in overlapped subsets are interpolated from two adjacent subsets. A switching law without constraint on the average dwell time is obtained which makes the conclusion less conservative. Furthermore,a systematic algorithm is developed to improve the efficiency of the controllers design process. The parameter set is divided into the fewest subsets on the premise that the closed-loop system has a desired performance. Simulation results demonstrate the effectiveness of this approach.     

直接力控制的特征结构配置法

以现代控制理论和飞行力学原理为基础，针对直接力控制器设计中存在的模态耦合问题，提出一种应用状态反特征结构配置进行解耦的方法，并出相应的公式。分析表明，用此方法对系统的极点和特征向量可以进行希望的配置。并能达到设计要求，同时仿真结果说明，用状态反馈特征结构配置法设计的控制系统比用线性二次型调节器（LQR）方法设计的控制系统解耦性能好，响应速度快，并且解决了输出反馈特征结构配置不能确保闭环系统稳定的问题。     

动态负调约束下固体冲压发动机燃气流量控制算法研究

变流量固体冲压发动机工作过程中，常采用控制燃气发生器压强的方式调节燃气生成量，在跟踪变化压强指令过程中，流量会产生明显的负调现象，严重影响发动机系统的安全性和可靠性。为 解决这一问题，本文以具有高度非线性、强时变特性的燃气发生器系统为对象，构建了基于粒子群算法的流量调节自适应PI控制器，并给出一种利用自适应微分跟踪器对期望控制指令进行“整形”的负调改善算法；首先，结合负调发生、终止判据，综合考量系统流量安全裕度，负调发生方向，构建了适配于动态负调约束的自适应跟踪微分器（TD），克服了传统跟踪微分器在负调抑制过程中控制精度不高，指向性不强等缺陷；进一步，开展了多工况下的负调抑制算法仿真校验，结果表明：所设计自适应控制算法具备良好的燃气流量控制能力，可实现在基本不改变响应时间情况下，将最大负调量削减56.6%的控制效果，展现出良好的工程应用前景。     

基于跟踪微分器的高超声速飞行器Backstepping控制

针对存在模型参数不确定和外部干扰的高超声速飞行器（HFV）跟踪控制问题,提出一种基于Backstepping方法的抗饱和非线性控制器。将飞行器纵向动力学模型分为速度子系统和航迹倾角子系统,然后针对每个子系统单独设计控制器。设计跟踪微分器获得信号的一阶导数,用以估计系统中的不确定干扰项和避免"微分项膨胀"问题。控制器设计过程考虑了控制量发生饱和的情况。基于Lyapunov理论证明了闭环系统信号的稳定性。与传统高超声速飞行器Backstepping方法相比,所设计的控制器采用待跟踪状态与理想控制指令之间的实际误差作为反馈量,放宽了对系统干扰项的限制,提高了控制器对控制增益变化的适应性,进而提高了闭环系统的跟踪控制性能。对比仿真结果验证了所设计方法的有效性。     

Attitude control without angular velocity measurement for flexible satellites

In this paper, by using quaternion models, the problem of attitude control is investigated for a class of flexible satellites. Two control laws are presented for the considered flexible satellite models to guarantee convergence of the closed-loop systems without using angular velocity measurement. One is in the form of a partial state feedback for the case where the modal variable is available, and the other is in the form of an observer-based partial state feedback for the case where the modal variable cannot be measured. Finally, an example is employed to illustrate the effectiveness of the proposed control laws.     

航空发动机控制系统性能恢复设计:H_∞/PR

对于航空发动机这样一类状态及输出矩阵存在摄动的系统,提出了一种直接根据性能指标作为恢复的目标的性能恢复理论设计方法。首先进行具有稳定及性能鲁棒性的状态反馈的H∞控制设计,然后通过设计一个状态观测器使得上述状态反馈控制的特性得以恢复。     

免疫反馈算法及其在航空发动机控制中的应用

基于生物免疫系统的反馈机理,针对现有免疫反馈算法在系统超调后性能恶化的不足,提出了一种新型的免疫反馈算法。该算法考虑了系统超调后的免疫响应过程,补充给出了系统超调初期、中期及后期的免疫规则。仿真结果表明,基于新型免疫规则的PID控制器超调更小、响应更快,抗干扰能力强,十分适用于大惯性对象和超调量大的系统。     

无人机着陆控制的特征结构配置方法实现

针对无人机纵向着陆系统的控制需求,采用特征结构配置方法的设计方案。阐述了全状态反馈理论基础上的特征结构配置的原理以及根据设计指标确定特征结构配置的方法,并对某型无人机纵向飞控系统动态响应进行分析,给出仿真实例。仿真结果表明,应用特征结构配置方法设计出的控制器,能够使飞机准确地跟踪期望轨迹,满足系统动态性能要求。在工程中具有一定的实用价值     

Quantitative speed control for SRM drive using fuzzy adapted inverse model

Quantitative and robust speed control for a switched reluctance motor (SRM) drive is considered to be rather difficult and challenging owing to its highly nonlinear dynamic behavior. A speed control scheme having two-degree-of-freedom (2DOF) structure is developed here to improve the speed dynamic response of an SRM drive. In the proposed control scheme, the feedback controller is quantitatively designed to meet the desired regulation control requirements first. Then a reference model and a command feedforward controller based on an inverse plant model are employed to yield the desired tracking response at nominal case. As the variations of system parameters and operating conditions occur, the prescribed control specifications may not be satisfied any more. To improve this, the inverse model is adaptively tuned by a fuzzy control scheme so that the model-following tracking error is significantly reduced. In addition, a simple disturbance cancellation robust controller is added to improve the tracking and regulation control performances further.     

变结构控制在两轮平衡小车中的应用

通过给出一种两轮平衡小车系统受非完整约束的动力学模型,基于此模型,利用变结构控制找出了滑模超平面,并设计出了该系统的调节控制律.经过Matlab/Simulink仿真,然后通过变结构控制器和状态反馈控制器的比较,得出此系统变结构的鲁棒性较好.进而通过实践验证,小车可控并可观,表明用该方法设计的控制器能够完成我们的预期目标.     

带有可调喷注器与文氏管的变推力液体火箭发动机响应特性分析

本文利用数值方法和解析方法对带有可调喷注器和可调文氏管的变推力液体火箭发动机的响应特性进行了分析,讨论了影响此类发动机动态性能的主要因素.最后给出发动机参数的优化结果,并进行了实验验证.     

电动力绳系离轨系统电流与拉力混合展开控制

电动力绳系离轨系统是一种典型的空间碎片主动消除技术,本文针对电动力绳离轨系统在初始阶段展开的控制问题,仅通过调节有限的系绳张力与电流,不依赖其他推进器,将导电系绳释放至期望长度并抑制系绳的摆动。首先,采用倾斜偶极子地磁场模型,建立考虑系绳质量的近地轨道二体电动力绳系卫星系统动力学模型;其次,在系绳张力与电流存在约束的条件下,采用反步法结合抗饱和辅助函数解决控制输入受限问题,并引入动态尺度广义逆实现了欠驱动电动力绳系统展开稳定控制问题;然后,应用Lyapunov稳定性定理证明了其闭环系统的稳定性;最后,在MATLAB/SIMULINK平台上进行了仿真验证。结果表明：通过调节系绳张力与电流,可以将系绳释放到指定位置,同时控制输入满足约束条件。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.