共查询到20条相似文献,搜索用时 46 毫秒
1.
微小型电动垂直起降无人机总体设计方法及特殊参数影响 总被引:1,自引:0,他引:1
《航空学报》2017,(10)
针对微小型电动垂直起降无人机(VTOL mEUAV),分析其设计难点,通过理论分析提出了一种基于特殊参数的总体设计方法,并基于算例进行了特殊参数的计算和影响分析。从翼载荷的选择、起飞总重迭代估计、无人机的平衡与操纵分析和飞翼布局设计方面详细阐述总体设计方法的过程,并针对特殊设计的一套动力系统X型飞翼尾坐式垂直起降无人机,进行功重比、动力系统工作点特性匹配及动力系统安装角等特殊参数的选择和影响分析,最终基于设计结果进行原理样机制作与飞行试验,证明了设计方法的有效性。研究结果表明,不同设计目标会引起翼载荷的选择和功重比的变化,螺旋桨与电机的匹配特性极大地影响动力系统效率与能源选择,合理选择动力系统的安装角与偏转方向可在基本不影响整体性能的情况下有效地改善操纵特性。 相似文献
2.
目前,中小型活塞动力无人机所配备的螺旋桨主要是两叶定距螺旋桨,其桨叶布局特征主要体现桨尖和桨根较窄,桨叶中部较宽,但在实际使用中发现,此类螺旋桨匹配无人机后飞行性能表现不佳。针对低速中小型活塞动力无人机,设计一种矩形薄型直桨叶二叶螺旋桨方案。将该螺旋桨方案与其他七种方案进行风洞试验,分别对各方案在零风速和巡航速度下的性能特性进行系统研究。结果表明:与其他方案相比,采用矩形桨叶设计的螺旋桨在静推力、功率、效率、拉力系数、功率系数等关键性指标上均表现出优异特性,尤其是在同样功率输入下,具有最低转速的特性,因此该方案螺旋桨具有优良的装机匹配特性。 相似文献
3.
针对舰载无人机滑跃起飞性能参数的选择问题,文章采用 Matlab/Simulink建立了滑跃起飞模型,分析了不同推重比、停机角、甲板风速、纬度和环境温度时无人机滑跃起飞性能的变化情况。计算结果表明:停机角和甲板风速对起飞性能影响大,应着重关注;低纬度地区比中纬度地区需要更大的推力保证起飞安全。文章结论对后续 无人机的滑跃起飞试验有借鉴意义。 相似文献
4.
5.
结合某垂直起降无人机对螺旋桨的总体设计要求,分析了同时满足两个设计点的螺旋桨设计难点,完成了对所设计螺旋桨性能要求的验证,探究了两个设计点对螺旋桨设计性能的影响及影响因素,获得对设计的指导性结论.通过CFX软件进行悬停和巡航状态下的数值计算,并与其车载试验结果进行对比,结果表明:设计螺旋桨可满足设计要求,且数值模拟与车载试验结果基本吻合,误差不超过11%.将设计螺旋桨与单个设计点的旋翼或巡航螺旋桨进行对比,分析影响因素,发现两个设计点将会降低螺旋桨在每个单独设计点的工作性能,且通过减小起飞总质量和巡航速度、增加动力系统个数和功率来缩小设计点间差异可降低设计难度和性能损失. 相似文献
6.
结合某高空飞艇螺旋桨的总体设计方案要求,完成螺旋桨的优化设计以及气动性能车载试验.采用叶素动量理论作为螺旋桨气动性能的计算方法,并通过风洞试验验证了该方法的可靠性.结合遗传算法对螺旋桨的弦长和扭转角进行了优化,使螺旋桨更加高效轻质,优化后螺旋桨设计点的气动效率增加了2.3%.建立螺旋桨车载试验测控系统,可以改变试验海拔高度和大气参数,得到优化设计螺旋桨不同工况的气动性能.试验结果表明,相同转速和来流条件下,海拔越高,螺旋桨的推力和扭矩越小.海拔为3-6km时,全尺寸高空飞艇螺旋桨计算推力和扭矩与试验结果的平均相对误差分别为2.8%和9.2%,两者基本吻合,从而验证了高空飞艇螺旋桨车载试验的准确性. 相似文献
7.
基于高斯伪谱航迹优化方法,建立了"火箭辅助型涡轮基组合动力"的飞行器/推进系统匹配分析方法,针对地面水平起降、以马赫数5巡航的高超声速飞行器,以巡航航程最远为目标,完成了涡轮基组合动力(TBCC)与火箭的耦合特性分析及匹配优化设计。研究结果表明:对于可行的TBCC方案(起飞推重比为1.0),引入合适推力的火箭有助于提升加速爬升段的总效率并降低质量消耗,且对巡航航程有着一定的提升(4%起飞重量推力火箭可增加航程0.97%);对于不可行的TBCC方案(起飞推重比为0.8),引入火箭不仅可实现推进系统方案的收敛,且其巡航航程相比可行的TBCC方案最多可增加7.9%。考虑到TBCC较大的"死重"和较低的单位迎面推力对巡航性能的不利影响,结构质量占比为25%的巡航型飞行器建议采用"13%起飞重量推力火箭辅助起飞推重比为0.7的TBCC "推进系统。相比之下,结构质量占比为55%的加速型飞行器建议采用" 5%起飞重量推力火箭辅助起飞推重比为0.98的TBCC"推进系统。 相似文献
8.
飞机的飞行性能与重心(CG)位置密切相关,尤其是后掠式无尾飞机的重心位置对其飞行性能影响更甚,如果重心位置发生变化,升力分布随之改变,进而影响飞机航时。针对这个问题,从气动布局和设计方法两方面,设计了一种航时对重心位置不敏感的无尾无人机(UAV)。气动布局上,提出了利用螺旋桨动力配平纵向力矩的鸥翼(GW)布局,以减小重心位置变化对升阻特性的影响;设计方法上,采用稳健性优化设计(RDO)理论,分析重心位置不确定时的航时低敏感度问题。以一架小型电动无人机为研究对象,建立了无尾无人机稳健性优化设计环境,包括总体设计、代理模型构造以及稳健性优化。分析结果表明:利用螺旋桨动力配平的鸥翼布局使重心可用范围增加了5%;静安定裕度在5%~15%变化时,该布局可以有效提高航时稳健性。采用稳健性优化得到的无人机几何参数,大幅度降低了重心位置对航时的影响,显著提升了满足约束的概率。 相似文献
9.
10.
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献