连续式跨声速风洞设计关键技术

为研制先进飞行器,除了提高现有风洞试验测量精度和改进试验技术外,必须建立高性能连续式跨声速风洞试验设备,解决飞行器高速风洞试验模拟能力和精细化模拟问题。以试验段尺寸0．6m×0．6m连续式跨声速风洞设计为例,给出了风洞总体设计方案,分析了如何降低风洞气流脉动、如何改善风洞流场品质、提高风洞运转效率和拓展风洞试验能力等关键技术途径。该风洞作为大型连续式跨声速风洞的引导风洞,方案设计主要采用了高压比压缩机驱动系统、半柔壁喷管、低噪声试验段、高性能换热器和三段调节片加可调中心体式二喉道等新型技术。     

An active vibration control method based on energy-fuzzy for cantilever structures excited by aerodynamic loads

In wind tunnel tests for the full-model fixed with sting, the low structural damping of the long cantilever sting results in destructive low-frequency and large-amplitude vibration. In order to obtain high-quality wind tunnel test data and ensure the safety of wind tunnel tests, an energy-fuzzy adaptive PD (Proportion Differentiation) control method is proposed. This method is used for active vibration control of a cantilever structure under variable aerodynamic load excitation, and real-time adjustment of parameters is achieved according to the system characteristics of vibration energy. Meanwhile, a real-time method is proposed to estimate the real-time vibration energy through the vibration acceleration signal, and the average exciting power of aerodynamic load is obtained by deducting the part of the power contributed by the vibration suppressor from the total power. Furthermore, an energy-fuzzy adaptive PD controller is proposed to achieve adaptive control to the changes of the aerodynamic load. Besides, the subsonic and transonic experiments were carried out in wind tunnel, the results revealed that comparing to fixed gain PD controllers, the energy-fuzzy adaptive PD controller maintains higher performance.     

跨声速风洞高速段一体化数值模拟研究

追求高亚声速经济巡航的民机、跨声速高机动特性的战斗机对高性能跨声速风洞的需求日趋紧迫,开 展跨声速风洞高速段一体化数值模拟研究,对跨声速风洞设计具有一定的参考意义。通过非对称平板扩压器 算例,初步验证计算方法的可行性,并对跨声速风洞高速段进行计算收敛评判方法、不同初始条件和槽壁扩张 角等因素研究。结果表明:采用模型区前后两个监测点马赫数变化作为收敛判据,方法可行且模型区流场均 匀;不同初始化条件对收敛结果总体影响较小,特别是各截面流场分布和槽道流动方向上,两者结果基本相同; 跨声速状态槽壁扩张角0.3°得到的试验段模型区域流场品质较槽壁扩张角0.0°更均匀。     

发动机和尾喷管匹配引起的跨音振动

本文论述某机在试飞中,飞行状态为H=3000～4000m,Ma=0.82～0.96范围内出现跨音速振动。通过多种途径,寻找“涡”存在的部位,并且为进一步揭示振源的本质,而进行飞机模型吹风和尾喷口模型气流脉动试验,终于找到了气流脉动的原因。最后,采取改装机尾罩,通过试飞实践,排除这一振动,使飞机顺利地通过跨音速试飞。      

Constrained layer damping treatment of a model support sting

In transonic wind tunnel tests, the pulsating airflow is prone to induce the first order resonance of the sting support system. The resonance limits the wind tunnel test envelope, makes the test data inaccurate, and brings potential security risks. In this paper, a model support sting with constrained layer damping (CLD) treatment is proposed to reduce the first order resonance response. The CLD treatment mainly consists of material selection and geometric optimization processes. The damping performance of the optimized CLD sting is compared with an AISI 1045 steel sting with the identical diameter in laboratory. The frequency response curves of the CLD sting support system and the AISI 1045 steel sting support system are obtained by sine sweep tests. The test results show that the first order resonance response of the CLD sting support system is 37.3% of that of the AISI 1045 steel sting support system. The first order damping ratios are calculated from the frequency response curves by half power point method. It is found that the first order damping ratio of the CLD sting support system is approximately 2.6 times that of the AISI 1045 steel sting support system.     

2.4m跨声速风洞大型飞机试验不确定度评估

2.4m跨声速风洞作为中国目前唯一的大型跨声速气动力试验设备,在中国大型飞机研制中发挥着十分重要的作用。因此,对该风洞试验数据质量的评估、控制和改进提高是一项紧迫的工作。笔者通过完善不确定度计算方法、详细标定基本不确定度源和编制评估软件等工作,建立了该风洞大型飞机试验的不确定度评估方法,并对某大型飞机模型试验结果开展了具体的评估与分析,澄清了该风洞大型飞机试验数据的质量水平。     

跨音速飞机模型试验洞壁干扰数值模拟的初步研究

分别以固壁条件和洞壁附近实测的压力分布,模拟各类实壁和透气壁试验段的洞壁边界条件,利用N-S方程数值求解模型在风洞中的绕流场,得出洞壁干扰对跨音速模型绕流的影响和气动力修正结果。初步研究结果表明,该方法能较有效地模拟模型在跨音速风洞中的绕流场,GBM04A模型在0.6m风洞中的试验结果经洞壁干扰修正后与无干扰参考结果吻合较好。     

复合材料超临界机翼跨音速颤振实验与数值计算研究

颤振课题是飞机设计过程中常常遇到的一个关键技术问题。以支线客机ARJ21超临界机翼颤振特性研究为背景,在俄罗斯TsAGI的T-106风洞中完成了该复合材料机翼跨音速颤振实验,基于N-S方程和无限插值方法（TFI）生成三维贴体运动网格对超临界机翼跨音速颤振进行了并行计算。结果表明：复合材料的超临界机翼在跨音速区域具有跨音速颤振＂凹坑＂现象;与风洞实验结果相比,有较好的一致性,为使用超临界机翼的运输类飞机跨音速颤振特性预计提供了一定的参考。     

Computational study of wing deformation and sting interference effects with the CAE-AVM test case

A modern transonic computational fluid dynamics test case is described in this paper, which is the Aerodynamic Validation Model (AVM) from the Chinese Aeronautical Establishment (CAE). The CAE-AVM is a representation of a modern transonic business jet aircraft with a design Mach number of 0.85. Numerical simulations for the AVM are conducted for two geometries: one baseline geometry, and one geometry that includes the applied model support system of the wind tunnel as well as the deformed wing shape that occurred during wind tunnel testing. The combined influence of wing deformation and model support interference on local and integral aerodynamic features is presented. Comparisons between CFD and experimental results are made; reasons of discrepancy between results from considered cases are analyzed.     

Wind tunnel test of gust load alleviation for a large-scale full aircraft model

Wind tunnel test is an important way to test the performance of Gust Load Alleviation(GLA). At present, some component-level wind tunnel tests have been carried out in big aviation countries, but there is a lack of full aircraft model GLA tests. In this study, a set of large-scale GLA test system in low-speed wind tunnel is developed, which includes a gust generator, a fivedegree-of-freedom suspension system, a full elastic aircraft model with control system, and gust load measuring devices. Two...     

Initial virtual flight test for a dynamically similar aircraft model with control augmentation system

To satisfy the validation requirements of flight control law for advanced aircraft,a wind tunnel based virtual flight testing has been implemented in a low speed wind tunnel.A 3-degree-offreedom gimbal,ventrally installed in the model,was used in conjunction with an actively controlled dynamically similar model of aircraft,which was equipped with the inertial measurement unit,attitude and heading reference system,embedded computer and servo-actuators.The model,which could be rotated around its center of gravity freely by the aerodynamic moments,together with the flow field,operator and real time control system made up the closed-loop testing circuit.The model is statically unstable in longitudinal direction,and it can fly stably in wind tunnel with the function of control augmentation of the flight control laws.The experimental results indicate that the model responds well to the operator's instructions.The response of the model in the tests shows reasonable agreement with the simulation results.The difference of response of angle of attack is less than 0.5°.The effect of stability augmentation and attitude control law was validated in the test,meanwhile the feasibility of virtual flight test technique treated as preliminary evaluation tool for advanced flight vehicle configuration research was also verified.     

跨声速风洞全模颤振试验技术

介绍了跨声速全模颤振试验的发展现状和存在的问题。探讨了全模颤振试验对风洞和支撑系统等试验设备的要求。对于风洞,主要从风洞洞体和流场等方面分析了进行颤振试验所需要具备的性能,并以中国空气动力研究与发展中心的2.4m跨声速风洞为例,介绍了进行颤振试验必须要采取的控制措施。对于支撑系统,则从模型运动自由度、支撑系统稳定性和支撑系统频率等方面的要求,阐述了设计支撑系统的困难,并简要分析了目前国内外发展的多种全模颤振支撑系统的结构原理及其优缺点。然后介绍了系统安全的保证措施,包括支撑系统稳定性分析、风洞紧急停车控制系统和模型保护装置等。最后根据飞行器发展的需求,探讨了今后需要完善和发展的几个主要问题。     

Experience in the use of computational aerodynamics to predict store release characteristics

In the early days, store separation tests were conducted in a hit or miss fashion—the stores would be dropped from the aircraft at gradually increasing speeds until the store came close to or sometimes actually hit the aircraft. In some cases, this led to loss of the aircraft, and made some test pilots reluctant to participate in store separation flight test programs.During the 1960's, the Captive Trajectory System (CTS) method for store separation wind tunnel testing was developed. The CTS provided a considerable improvement over the hit or miss method, and became widely used in aircraft/store integration programs prior to flight-testing. However, since fairly small-scale models had to be used in the wind tunnel tests, in many cases the wind tunnel predictions did not match the flight test results. No mechanism was then in place to resolve the wind tunnel/flight test discrepancies.During this same time frame Computational Fluid Dynamics (CFD) had finally matured to the point of providing a trajectory solution for a store in an aircraft flowfield. However, since the computational tools were necessarily (due to computer resource limitations) limited to linear techniques, and since most store separation problems occur at transonic speeds, these tools had limited application.Recent advances in computer resources have greatly improved the capability of CFD to predict store release characteristics. Instead of using linear or approximate schemes, time dependent Euler and Navier Stokes trajectories could be computed in a reasonable time frame.Three international CFD Challenges, held during the last decade of the 20th century, have shown that CFD can not only match wind tunnel test data, but also predict flight test trajectories for complex stores at transonic speeds. It appears that CFD has matured to the point that it can be usefully integrated into aircraft/store compatibility programs.     

2.4米跨声速风洞大展弦比飞机测力试验技术研究

针对大展弦比飞机的气动布局特点,在2.4米跨声速风洞中开展了大展弦比飞机测力试验技术研究。该项研究建立了大升阻比高精度天平设计技术和模型支撑系统设计平台,研制了专用大升阻比高精度测力天平和模型支撑系统。在国内高速风洞中建立了大型跨声速风洞模型设计新准则。研究结果表明:所提出和制定的方案是科学合理的,为我国大飞机研制提供了可靠的技术支撑。     

宽体客机高速风洞试验数据修正方法

宽体客机航程远、巡航马赫数高，其气动设计对风洞试验数据精准度要求很高。通过完善中国空气动力研究与发展中心FL-26风洞试验数据修正技术和设备，对宽体客机高速风洞测力试验数据进行支撑/洞壁干扰、模型变形及流场畸变等系统修正，获取干净、可靠的风洞试验基准数据，为开展雷诺数、静气动弹性和动力影响等相关性修正奠定基础。研究表明：支撑干扰试验时，尾腔压力分布测量位置和假支杆长度伸入模型尾腔50 mm即可获得可靠的支撑干扰试验结果；在试验包线范围内，洞壁干扰对宽体客机模型升力、阻力和俯仰力矩系数影响较小；试验模型变形对宽体客机气动特性影响较为明显，马赫数0.85时模型变形后的升力线斜率减小0.005左右，焦点前移0.021 b_A，需进行相关修正。     

双目视觉绳系支撑飞行器模型位姿动态测量

绳牵引并联机器人（WDPR）为风洞试验提供了一种新型支撑方式，可用于多/六自由度风洞复杂动态试验。针对该支撑下飞行器模型的大范围运动，发展了一种基于双目视觉的模型位姿动态测量方法。首先，设计了一种编码合作标志点，合理布置于模型表面，通过图像处理消除绳对标志点成像干扰，进行标志点三维重构；然后，利用绝对定姿算法求解相对位姿初值，且给出了理论误差分析，并基于双目相机重投影误差构建李代数下的无约束最小二乘优化问题，采用L-M算法进行位姿优化；最后，采用该测量系统分别进行了静态和动态精度验证试验，以及大迎角俯仰振荡等3种单/多自由度典型运动轨迹测量。试验数据显示，静态角度和位移测量精度分别优于0.02°/0.02 mm；动态测量时角度精度可达到0.1°量级，位移平均误差为0.4 mm。研究结果表明：设计的双目视觉测量系统是有效可行的，可为后续风洞试验的实际应用提供支持。     

CFD/CSD-based flutter prediction method for experimental models in a transonic wind tunnel with porous wall

To predict the flutter dynamic pressure of a wind tunnel model before flutter test, an accurate Computational Fluid Dynamics/Computational Structural Dynamics (CFD/CSD)-based flutter prediction method is proposed under the conditions of a 2.4 m × 2.4 m transonic wind tunnel with porous wall. From the CFD simulations of the flows through an inclined hole of this wind tunnel, the Nambu’s linear porous wall model between the flow rate and the differential pressure is extended to the porous wall with inclined holes, so that the porous wall can be conveniently modeled as a boundary condition. According to the flutter testing approach for the current wind tunnel, the steady CFD calculation is conducted to achieve the required inlet Mach number. A time-domain CFD/CSD method is then employed to evaluate the structural response of the experimental model, and the critical flutter point is obtained by increasing the dynamic pressure step by step at a fixed Mach number. The present method is applied to the flutter calculations for a vertical tail model and an aircraft model tested in the current transonic wind tunnel. For both models, the computed flutter characteristics agree well with the experimental results.     

飞机全动平尾颤振特性风洞试验

高机动飞机全动平尾颤振设计的重要手段就是颤振模型风洞试验。针对一个飞机的全动平尾,采用了单独平尾和中央固支的后机身-平尾组合体两种方案的低速颤振风洞试验,研究平尾的基本颤振耦合机理以及后机身垂尾气动力干扰的影响。然后采用半模跨声速颤振风洞试验研究马赫数对颤振特性的影响和机翼干扰对平尾颤振边界的影响。介绍了低、高速颤振模型的设计和风洞试验的结果,并综合形成了完整的平尾颤振特性规律,尤其在跨声速颤振风洞试验中,使用不同超重系数的颤振模型,研究了质量参数对颤振边界的影响规律。风洞试验结果显示,全动平尾颤振特性研究必须考虑后机身的弹性支持,并且需要使用不同的模型方案考虑机身、机翼和垂尾的气动力干扰,跨声速风洞模型需要考虑超重系数的影响。该研究获得了全动平尾颤振特性的一般规律,可作为相关飞行器设计的参考。     

二维柔壁自适应壁风洞中三维模型近音速试验技术

根据跨音速面积律将翼-身组合体模型转变为等效旋成体模型 ;并将风洞的矩形截面转变为等面积圆截面 ;由此通过轴对称跨音速小扰动速势方程求解圆截面风洞洞壁调节量 ;进而得到矩形截面上、下洞壁调节量。以堵塞比为 2 .64%的模型在西北工业大学高速二维柔壁自适应壁风洞中进行了翼面测压试验,并以同一模型在德国宇航院 HKG风洞中 (堵塞比为0 .35 % )做了对比试验。在近音速情况下 ( Ma∞=0 .94,0 .994和 1 .0 0 8),α=0°,2°时两者结果符合良好     

2.4m跨声速风洞多功能支撑系统试验技术研究

针对型号研制的风洞试验需求,在2.4m跨声速风洞中开展了多功能支撑系统试验技术研究,研制了一套多功能支撑系统。该支撑系统既可实现定侧滑角连续变迎角的试验方式,又可实现定迎角连续变侧滑角的试验方式。在0.6m跨声速风洞开展了引导性试验研究,并在2.4m跨声速风洞中对该支撑系统与传统的支撑方式进行了风洞试验对比。结果表明,多功能支撑与传统支撑方式的风洞试验数据相关性良好,表明该支撑装置的研制是成功的,可应用于型号试验。