Performance of the Analog Moving Window Detector

A type of analog integrating moving window detector for use with a scanning pulse radar is examined. A performance analysis is carried out, which takes into account both the radiation pattern of the antenna and the dynamic character of the detection process due to the angular scanning of the antenna. An expression for the false alarm rate of the detector is first derived and evaluated numerically. The detection performance and angular accuracy are next determined in a direct Monte Carlo simulation of the detector on a digital computer for both no fading and pulse-to-pulse Rayleigh fading. Finally the influence on detection performance of the width used for the moving window is investigated.     

Comparison of Two Scanning Radar Detectors: The Moving Window and the Feedback Integrator

A comparison is made between the moving window and feedback integrator detectors for a scanning radar. Detection probabilities and position estimates are calculated by using a Monte Carlo simulation. The moving window is a slightly better detector than the feedback integrator: it provides 0.5-dB better detection capability and 8 percent more accurate estimate of position. However, the feedback integrator can be implemented more easily.     

Evaluation of Collapsing Losses in Digital Radar Detection

The collapsing losses, due to multiple channel combinations, are evaluated for some digital radar detection schemes including the moving window detector.     

Moving target detection via airborne HRR phased array radar

We study moving target detection in the presence of temporally and spatially correlated ground clutter for airborne high range resolution (HRR) phased array radar. We divide the HRR range profiles into large range segments to avoid the range migration problems that occur in the HRR radar data. Since each range segment contains a sequence of HRR range bins, no information is lost due to the division and hence no loss of resolution occurs. We show how to use a vector autoregressive (VAR) filtering technique to suppress the ground clutter. Then a moving target detector based on a generalized likelihood ratio test (GLRT) detection strategy is derived. The detection threshold is determined according to the desired false alarm rate, which is made possible via an asymptotic statistical analysis. After the target Doppler frequency and spatial signature vectors are estimated from the VAR-filtered data as if a target were present, a simple detection variable is computed and compared with the detection threshold to render a decision on the presence of a target. Numerical results are provided to demonstrate the performance of the proposed moving target detection algorithm     

非参量量化秩检测器的性能研究

 许多作者讨论过非参量秩检测器在雷达信号处理中的应用。秩检测器首先把接收波形样本转换为秩。如果检验单元和参考单元的噪声样本独立和分布,则无信号时检验单元的秩具有离散均匀分布,与输入噪声的分布无关。所以秩检测器可能提供分布自由的恒虚警率性能。量化秩检测器（QRD）只对二进量化秩进行积累,所以它实现起来很经济。本文分析QRD的检测性能。证明QRD有一最佳秩量化门限（ORQT）。确定高斯和韦伯噪声中的ORQT。另外,把QRD同高斯噪声中的局部最佳秩检测器和最佳参量检测器进行比较。     

Performance of MAX family of order-statistic CFAR detectors

The MAX family of constant-false-alarm-rate (CFAR) detectors is introduced as a generalization of the greatest of CFAR (GO-CFAR) or MX mean-level detector (MX-MLD). Members of the MAX family use local estimators based on order statistics and generate both a near-range and a far-range noise-level estimate. Local estimates are always combined through a maximum operation; this insures false-alarm control at clutter edges. At the same time, order-statistic-based estimators result in a high-resolution detector. A complete detection analysis is provided for SWII targets and a reference channel contaminated by large outliers. Results are presented for the MX censored MLD (MX-CMLD) operating in clutter. The MX order statistic detector (MX-OSD) based on only a single-order statistic per window, is analyzed, and curves showing the required threshold, CFAR loss, optimum censoring point, and signal-to-noise ratio (SNR) loss in the presence of outliers are given. Simulations are used to compare the dynamic responses of various MX-OSD detectors in a clutter and a multiple-target environment     

A mean level adaptive detector using nonconcurrent data

Convergence results for a mean level adaptive detector (MLAD) are presented. The MLAD consists of an adaptive matched filter (for spatially correlated inputs) followed by a mean level detector (MLD). The optimal weights of the adaptive matched filter are estimated from one batch of data and applied to a statistically independent batch of nonconcurrent data. The threshold of the MLD is determined from the resultant data. Thereafter a candidate cell is compared against this threshold. Probabilities of false alarm and detection are derived as a function of the threshold factor, the order of the matched filter, the number of independent samples per channel used to calculate the adaptive matched filter weights, the number of samples used to set the MLD threshold, and the output signal-to-noise power ratio of the optimal matched filter. A number of performance curves are shown and discussed     

A variably trimmed mean CFAR radar detector

A variably trimmed mean (VTM) constant false alarm rate (CFAR) detector in which the threshold is determined by processing a linear combination of a group of ordered samples in each window is introduced. Unlike the trimmed mean detector, the number of ordered samples that require further processing is allowed to vary according to a data-dependent rule. It is demonstrated that the VTM detector exhibits performance characteristics that are independent of the total (stationary) noise power. Simulated performance results are presented for regions of clutter power transitions and for multiple target environments to illustrate the possible improvement over the order-statistic detector that can be obtained by using a VTM detector     

Performance of a Two-Sample Mann-Whitney Nonparametric Detector in a Radar Application

The detection of signals in an unknown, typically non-Gaussian noise environment, while attempting to maintain a constant false-alarm rate, is a common problem in radar and sonar. The raw receiver data is commonly processed initially by a bank of frequency filters. The further processing of the outputs from the filter bank by a two-sample Mann-Whitney detector is considered. When the noise statistics in all filters are identical, the Mann-Whitney detector is distribution free, i. e., the false-alarm probability may be prescribed in advance regardless of the precise form of the noise statistics. The primary purpose of this paper is to demonstrate the potential advantage of nonparametric detectors over conventional detectors. The signal detection performance of the Mann-Whitney detector is compared to that of an ordinary linear envelope detector plus integrator in the presence of Gaussian and several hypothetical forms of non-Gaussian noise. This comparison is made for both uniform and nonuniform distributions of noise power across the filter bank. Besides providing a much more constant false-alarm rate than the conventional detector, the Mann-Whitney detector's signal detection performance is found also to be much less sensitive to the form of the noise statistics. In one case, its detection sensitivity is found to be 11 dB better than that of the conventional detector. Even when the noise power density is made moderately nonuniform across the filter bank, the detection performance of the Mann-Whitney detector is found not to be significantly affected.     

Weak Signal Detection in Non-Gaussian Noise of Unknown Level

An adaptive threshold detector to test for the presence of a weak signal in additive non-Gaussian noise of unknown level is discussed. The detector consists of a locally optimum detector, a noise level estimator, and a decision device. The detection threshold is made adaptive according to the information provided by the noise level estimator in order to keep a fixed false-alarm probability. Asymptotic performance characteristics are obtained indicating relationships among the basic system parameters such as the reference noise sample size and the underlying noise statistics. It is shown that, as the reference noise sample size is made sufficiently large, the adaptive threshold detector attains the performance of a corresponding locally optimum detector for detecting the weak signal were the noise level known.     

Frequency-hopping signal detection using partial band coverage

The performance of a channelized radiometer in detecting a frequency-hopping signal is analyzed for a variable number of parallel radiometers not necessarily covering the entire hopping band. The full band may not be covered because of an attempt to avoid interfering signals, limited radiometer resources, lack of knowledge of the band frequency location, or combinations of these factors. The analysis provides for calculation of the value of the signal-to-noise ratio (SNR) required to achieve a given probability of detection for a specified false-alarm rate, assuming an observation interval equivalent to N hops using either a fixed or a moving observation window. The dependence of the probability of detection on a misalignment of the detector observation intervals with the hop transitions is also analyzed. Numerical results are presented and discussed. Applied to a typical slow-hopping VHF radio, the results imply that a 150-hop transmission can be detected by a channelized radiometer covering half the hopping band when the SNR is about 2 dB     

Angular Accuracy of a Scanning Radar Employing a Two-Pole Filter

A two-pole filter is proposed as a detector for a scanning radar. The optimum values of the filter coefficients are found and are approximated by a simple expression. The optimum two-pole filter requires a 0.15-dB increase in signal-to-noise ratio in order to provide the same detection capability as the optimum detector, and yields azimuth estimates whose standard deviation are within 15 percent of the Cramér-Rao lower bound. The estimator is simple to implement, avoiding the storage requirements of the moving window detector and the bias complications of the feedback integrator.     

Modified Generalized Sign Test Processor for 2-D Radar

The modified generalized sign test processor is a nonparametric, adaptive detector for 2-D search radars. The detector ranks a sample under test with its neighboring samples and integrates (on a pulse-to-pulse basis) the ranks with a two-pole filter. A target is declared when the integrated output exceeds two thresholds. The first threshold is fixed and yields a 10-6 probability of false alarm when the neighboring samples are independent and identically distributed. The second threshold is adaptive and maintains a low false-alarm rate when the integrated neighboring samples are correlated and when there are nonhomogeneities, such as extraneous targets, in the neighboring cells. Using Monte Carlo techniques, probability of false-alarm results, probability of detection curves, and angular accuracy curves have been generated for this detector. The detector was built and PPI photographs are used to indicate the detector's performance when the radar is operated over land clutter.     

Energy Detection of a Random Process in Colored Gaussian Noise

A likelihood receiver for a Gaussian random signal process in colored Gaussian noise is realized with a quadratic form of a finite-duration sample of the input process. Such a receiver may be called a "filtered energy detector." The output statistic is compared with a threshold and if the threshold is exceeded, a signal is said to be present. False alarm and detection probabilities may be estimated if tabulated distributions can be fitted to the actual distributions of the test statistic which are unknown. Gamma distributions were fitted to the conditional probability densities of the output statistic by equating means and variances, formulas for which are derived assuming a large observation interval. A numerical example is given for the case in which the noise and signal processes have spectral densities of the same shape or are flat. The optimum filter turns out to be a band-limited noise whitener. The factors governing false alarm and detection probabilities are the filter bandwidth, the sample duration, and the signal level compared to the noise. Two sets of receiver operating characteristic curves are presented to complete the example.     

Optimum Detection of an Optical Image on a Photoelectric Surface

The detection of an optical image in the presence of uniform background light is based on a likelihood ratio formed of the numbers of photoelectrons emitted from small elements of a photoelectric surface onto which the image is focused. When diffraction is negligible and the surface has unit quantum efficiency, this detector is equipollent with the optimum detector of the image-forming light. Its performance is compared with that of the threshold detector and that of a detector basing its decisions on the total number of photoelectrons from a finite area of the image. The illuminance of the image is postulated to have a Gaussian spatial distribution. All three detectors exhibit nearly the same reliability.     

基于均匀性判定规则的统计MIMO雷达多通道融合检测技术

针对统计MIMO雷达各观测通道统计特性不一致的情况,提出了一种多通道融合检测技术。该技术利用均匀性判定规则,选择一组均匀的、"被认为是具有较高信杂噪比"的局部检验统计量来构建全局检验统计量,即新的检测器。给出了新检测器的设计步骤和均匀性判定规则,并利用全概率公式证明了新检测器的虚警概率与每一操作步骤中过门限概率的关系,从而为仿真得出检测门限提供了理论基础。仿真结果表明,在不同通道间信噪比分布类型条件下,新检测器的检测性能具有较强的稳健性,且与不同条件下性能最优的检测器相比,其性能损失很小。     

An Alternative Method for Analyzing the Double Threshold Detector

An alternative method for analyzing the performance of a double threshold or M-out-of-N detector is discussed. Detection performance for the suggested method is based on the probability that a return crosses the threshold for the Mth time (a detection is declared) on the kth return or look. It is shown that this formulation has many advantages, as compared with the conventional method of analysis which employs the binomial probability distribution, since the upper limit N is not contained in the resulting probability expressions. It is shown that the probability of detection obtained by the alternate method is the same as that obtained if the detection method were analyzed as a Markov chain with M+1 states. Use of the method results in simple expressions for the mean and variance of the number of looks before detection, provides an alternative way of estimating the probability of a threshold crossing, and leads to computationally simple bounds for the probability of false alarm.     

基于杂波对消-自聚焦的多通道SAR-GMTI

对超高频(UHF)波段多通道合成孔径雷达(SAR)动目标检测技术进行研究,解决了长相干积累时间导致动目标在方位向散焦严重的问题。采用分块自聚焦技术对多通道SAR地面移动目标指示(GMTI)系统自适应杂波抑制后的SAR图像进行处理,改善杂波抑制后的SAR图像中动目标的聚焦情况,增强动目标与周围剩余杂波的对比度,进而提高恒虚警率(CFAR)检测的性能。与传统杂波抑制后直接进行CFAR检测方法相比较,该方法降低了检测虚警概率。实测数据处理结果显示动目标的信杂比明显提高,动目标方位向聚焦成功,证明了该方法的有效性。     

Structures for radar detection in compound Gaussian clutter

The problem of coherent radar target detection in a background of non-Gaussian clutter modeled by a compound Gaussian distribution is studied here. We show how the likelihood ratio may be recast into an estimator-correlator form that shows that an essential feature of the optimal detector is to compute an optimum estimate of the reciprocal of the unknown random local power level. We then proceed to show that the optimal detector may be recast into yet another form, namely a matched filter compared with a data-dependent threshold. With these reformulations of the optimal detector, the problem of obtaining suboptimal detectors may be systematically studied by either approximating the likelihood ratio directly, utilizing a suboptimal estimate in the estimator-correlator structure or utilizing a suboptimal function to model the data-dependent threshold in the matched filter interpretation. Each of these approaches is studied to obtain suboptimal detectors. The results indicate that for processing small numbers of pulses, a suboptimal detector that utilizes information about the nature of the non-Gaussian clutter can be implemented to obtain quasi-optimal performance. As the number of pulses to be processed increases, a suboptimal detector that does not require information about the specific nature of the non-Gaussian clutter may be implemented to obtain quasi-optimal performance     

Detection by incoherent recombination with partial information

Matched filter (MF) detection in spread environments is often seriously degraded by the mismatch between the waveform replica and the composite signal formed by the spreading environment. Typically the spreading is caused by multiple delayed reflections due to scatter extent or multipath especially in shallow water sonar applications. It is possible to recover some detector performance by incoherent summation of weighted MF realizations in a process called incoherent recombining (IR). Several IR strategies for Gaussian data that assume varying amounts of prior scattering function (SF) information are examined, their receiver operating characteristics (ROCs) computed, and compared with those of the unrealizable “prescient” receiver (PR). They include optimally weighted and unweighted versions of the maximum likelihood estimator-correlator (EC), and variations of the “at-least-one” (ALO) detector that examines sequences of MF realizations declaring a detection if at least one threshold is crossed. As might be expected, performance improves with the accuracy of the prior information incorporated in the detector formulation