Cr在Ti-Al-Cr合金抗高温氧化过程中的作用研究

研究了 Ti-50 Al,Ti-50 Al-1 5Cr,Ti-4 5Al-1 5Cr和 Ti-67Al-8Cr(原子百分数 )合金在 90 0～ 1 0 0 0℃下的高温氧化性能。结果表明 :Ti-50 Al-1 5Cr,Ti-4 5Al-1 5Cr和 Ti-67Al-8Cr均表现出优良的抗氧化性能,氧化后表面主要是 α-Al₂O₃及少量的 TiO₂ 组成。Ti-50 Al-1 5Cr,Ti-67Al-8Cr和 Ti-4 5Al-1 5Cr合金良好的抗高温氧化性能归于 Cr在合金抗氧化过程中起到了吸氧效应的作用。另外发现对于 Ti-50 Al-1 5Cr和 Ti-67Al-8Cr均发生了 950℃时的氧化增重比 1 0 0 0℃时的氧化增重大,这是由于 Cr的加入使 Ti的活性降低的缘故。     

原位反应合成Nb掺杂Al2O3/TiAl复合材料的显微结构分析

利用Al-Ti-TiO2体系原位反应合成了Nb掺杂Al2O3／TiAl复合材料。借助XRD和SEM研究了Nb掺杂Al2O3／TiAl的显微结构以及Nb引入量对复合材料显微结构的影响。结果表明，复合材料由TiAl、Ti3Al、Al2O3、Nb和NbAl3相构成，细小Al2O3颗粒分布于基体晶粒交界处，存在一定的团聚；Nb元素引入量的高低，可调节产物中TiAl和Ti3Al的相对含量，随Nb含量的增大，TiAl含量逐渐减少，Ti3Al则逐渐增大；同时，基体晶粒和Al2O3颗粒均有所细化，且分布逐渐均匀，材料的均匀性得到改善。     

Ti-22Al-25Nb合金剪切旋压过程中显微组织演化

通过剪切旋压试验,研究了旋压温度(910℃和1000℃)和减薄率(0、10%和30%)对Ti-22Al-25Nb合金显微组织的影响,探讨了旋压过程中的显微组织演化规律。结果表明:Ti-22Al-25Nb(原子数分数)合金旋压组织主要由α2相、B2相和O相组成,在旋压过程中,B2晶粒沿旋轮进给方向被拉长,且伴随有动态再结晶现象发生;温度主要影响Ti-22Al-25Nb合金中α2相与O相的尺寸和形貌,随着旋压温度的升高,O相片层逐渐变短并粗化,α2相趋向等轴化;变形量主要影响α2相体积分数与O相形貌,随着减薄率的增大,α2相体积分数逐渐减少,O相从片层状转变为短棒状。因此,Ti-22Al-25Nb合金剪切旋压过程中不仅发生晶粒变形与动态再结晶现象,更涉及复杂的相变行为,组织控制困难。     

TiAl合金高温循环氧化行为及其表面改性研究

研究了TiAl金属间化合物及表面涂层在空气中的高温循环氧化行为。结果表明:在800℃时TiAl合金具有较好的抗高温氧化行为,但当温度高于800℃时,TiAl合金表面未能形成单一的Al2O3保护层,而是形成外3层为疏松的TiO2层,内层为TiO2+Al2O3的混合氧化物层,因而使得TiAl合金的抗高温循环氧化性能严重蜕化。TiAl合金经过Cr改性铝化处理后,表面形成了具有立方Ll2结构的Al67Ti26Cr7层,立方Ll2结构的Al67Ti26Cr7不仅具有较高的铝含量,而且具有优良的韧性,因而使得处理后的TiAl合金具有良好的抗高温循环氧化性能。铝化物涂层尽管有很高的铝含量,但由于铝化得到的TiAl3相具有四方形结构,涂层非常脆,故该涂层抗高温循环氧化性能有待进一步提高。     

Dy对EB-PVDβ-NiAl涂层高温瞬态氧化行为的影响(英文)

β-NiAl是一种有前景的应用于1150°C以上的抗氧化涂层材料。本文利用电子束物理气相沉积(EB-PVD)方法制备了0~0.5at%Dy含量的β-NiAl涂层,研究了涂层的瞬态氧化行为。1200°C时,在0.05at%Dy掺杂的涂层中只观察到了稳态α-Al2O3相,而在0.5at%Dy掺杂的涂层中,1h氧化过程中,发生了θ-Al2O3到α-Al2O3的相变。1100°C时,在最初的15min所有涂层均发生了θ-α相变。0.05at%Dy掺杂的涂层在45min的时候相变已经完成,这比0.5at%Dy掺杂涂层要早得多。过量Dy的掺杂能够延缓θ-α相变。未掺杂和过量掺杂涂层在20h氧化之后仍存在针状相θ-Al2O3,而0.05at%Dy掺杂的涂层中则为经典的颗粒状α-Al2O3形貌。     

Effects of B on the Microstructure and Oxidation Resistance of Nb-Ti-Si-based Ultrahigh-temperature Alloy

Nb-Ti-Si-based ultrahigh-temperature alloys concocted with boron ranging from 0 to 2 at% are prepared by arc-melting technology. The effects of adding boron on their as-melted microstructure and oxidation resistance are analyzed. The (Nb,Ti)ss, β-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ exist in Nb-22Ti-16Si-6Cr-3Al-4Hf alloy, while (Nb,Ti)ss, α-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ are present in Nb-22Ti-16Si-6Cr-3Al-4Hf-1B and Nb-22Ti-16Si-6Cr-3Al-4Hf-2B alloys. The oxidation of Nb-Ti-Si-based ultrahigh-temperature alloys is dominated by the diffusion of oxygen through (Nb,Ti)ss. Compared to boron-free alloys, the boron-containing alloys have significantly lower oxidation rate when oxidized at 1 200 °C for less than 50 h, but, for more than 50 h, their oxidation resistance deteriorates.     

Al_2O_3/TiAl 复合材料的原位合成、结构与性能研究(英文)

以 Ti, Al, TiO2和 Nb2O5混合粉为原料,采用热压反应合成技术制备了 Al2O3/TiAl 复合材料。对复合材料的微观组织与力学性能进行了研究。结果表明:产物由γ-TiAl, α2-Ti3Al, Al2O3和 NbAl3相组成。原位反应形成的细小 Al2O3粒子主要分布在基体晶界处。随着 Nb2O5含量的增加,晶粒明显细化,Al2O3粒子呈弥散分布在基体中。最终形成了由γ和γ α2构成的特殊组织。随着 Nb2O5含量的增大,复合材料的硬度逐渐增大,抗弯强度和断裂韧性在 Nb2O5含量为 6 wt%时达到最大,分别为 398.5 MPa 和 6.99 MPa·m1/2。     

Ti-6Al-4V合金氢致塑性效应与应用

利用光学显微镜研究了置氢处理后Ti-6A1-4V合金的微观组织,通过X射线衍射分析试验研究了置氢处理过程中的相转变过程;采用室温压缩试验研究了置氢处理后Ti-6Al-4V合金的变形行为,并进行了冷镦试验.结果表明,氢促进了α"马氏体与亚稳β相的形成,亚稳β相的形成与转变是Ti-6Al-4V合金变形性能提高的主要因素;在...     

激光沉积Ti-6Al-2Zr-Mo-V钛合金高周疲劳性能

 疲劳失效是钛合金工业应用中最重要的失效方式,疲劳强度是钛合金应用的关键性指标。为了研究激光沉积Ti-6Al-2Zr-Mo-V钛合金的疲劳性能和行为,在625 MPa到900 MPa不同应力水平下进行了室温高周疲劳(HCF)测试(应力比R=0.1,加载频率f=120~130 Hz),完成了疲劳断口表面分析。研究了气孔存在及分布对激光沉积Ti-6Al-2Zr-Mo-V钛合金疲劳性能的影响。激光沉积钛合金具有细小α/β片层组织。分析结果显示,虽然疲劳源区有气孔存在,激光沉积Ti-6Al-2Zr-Mo-V钛合金仍然具有优异的疲劳性能。取向丰富细小的α/β片层组织能有效减小疲劳源区滑移长度。分析结果还表明,应力水平对疲劳行为有一定影响。     

Grinding behavior and surface appearance of（TiC_p＋ TiB_w）/Ti-6Al-4V titanium matrix composites

（TiCp＋ TiBw）/Ti-6Al-4V titanium matrix composites（PTMCs） have broad application prospects in the aviation and nuclear field. However, it is a typical difficult-to-cut material due to high hardness of the reinforcements, high strength and low thermal conductivity of Ti-6Al-4V alloy matrix. Grinding experiments with vitrified CBN wheels were conducted to analyze comparatively the grinding performance of PTMCs and Ti-6Al-4V alloy. Grinding force and force ratios, specific grinding energy, grinding temperature, surface roughness, ground surface appearance were discussed. The results show that the normal grinding force and the force ratios of PTMCs are much larger than that of Ti-6Al-4V alloy. Low depth of cut and high workpiece speed are generally beneficial to achieve the precision ground surface for PTMCs. The hard reinforcements of PTMCs are mainly removed in the ductile mode during grinding. However, the removal phenomenon of the reinforcements due to brittle fracture still exists, which contributes to the lower specific grinding energy and grinding temperature of PTMCs than Ti-6Al-4V alloy.     

铸造钛合金的氢处理细化晶粒的研究

本文研究了氢处理（渗氢+共析处理+真空除氢）对铸造Ti-6Al-4V合金微观组织的影响。发现Ti-6A1-4V合金渗氢后析出片状的面心立方结构的TiH₂相。随含氢量的增加,TiH₂相趋于球化。渗氢试样经共析处理后,原晶界α消失,组织转变为α+TiH₂共析组织及少量残余β相。真空除氢后,组织变为细小的等轴组织。氢处理提供了一种细化铸造Ti-6Al-4V组织的有效途径。     

粉末冶金Ti-6Al-4V 的组织及形成机理

利用热等静压(HIP)技术及旋转电极粉,采用预合金粉工艺制备了全致密的粉末冶金Ti-6Al-4V合金,用光学显微镜对其金相组织进行了观察,分析其形成机理,并对粉末冶金Ti-6Al-4V合金的室温拉伸性能、弹性模量、冲击性能及断裂韧性进行了研究.结果表明:粉末冶金Ti-6Al-4V金相组织主要由条片α相+相间β相组成,有细小的等轴α相分布在晶粒界面处,包裹着条片α相,这种独特的组织状态是由制备工艺决定的,具有良好的综合性能.     

高Cr铸造镍基高温合金K4648与陶瓷型芯的界面反应研究

采用金相显微镜、扫描电镜及能谱、电子探针和X射线衍射对高Cr铸造镍基高温合金K4648等轴晶和定向凝固铸件的合金/陶瓷型芯界面反应进行了系统研究,获得反应时间与反应量关系的界面反应动力学曲线、不同反应时间的反应界面形貌及产物的种类。结果表明:高Cr铸造镍基高温合金K4648与铝基型芯不易发生反应,而与硅基陶瓷型芯发生剧烈的界面反应,反应产生金属瘤状凸起物,造成铸件内腔破坏。此外,白色的硅基型芯内部变成黑色,黑色反应区内含有一定量的Cr,Al,Ti元素。在反应的中、后期型芯黑色反应区内还存在着灰色区,该区的Cr,Al,Ti含量远高于黑色反应区。高Cr铸造镍基高温合金K4648合金与硅基陶瓷型芯反应分为:(1)富Cr,Al,Ti熔体向型芯内的渗入阶段;(2)富Cr,Al,Ti熔体与陶瓷型芯SiO2基体的反应;(3)富Cr,Al,Ti的熔体与型芯中Zr-SiO4颗粒反应三个阶段。反应过程中型芯存在局部液化现象。K4648合金/硅基陶瓷型界面反应产物主要为层状或树枝状Al2O3,块状Cr3Si金属间化合物、ZrO2,富Cr,Zr,Al,Ti的复合氧化物、共晶形态的富Cr,Si,Al,Ti的复合氧化物、块状或树枝状的富Ti,Al,Zr,Cr复合氧化物。反应产物中的Cr,Al,Ti元素来自合金熔体而Zr,Si,O来自陶瓷型芯。     

Primary Solidification Phase and Lamellar Orientation in Directionally Solidified Ti-45Al-7Nb Alloy

Primary solidification phase and lamellar orientation are investigated in Ti-45Al-7Nb alloy at very high ratio of temperature gradient to growth rate (G/v) by a liquid-metal-cooled directionally solidified method. It shows that Ti-45Al-7Nb alloy solidifies with primary α phase. Longitudinal (parallel to growth direction) microstructure shows that α dendrites in solid-liquid mushy zone are discontinuous and transverse microstructure of α dendrites is worm-like feature. Growth direction of α phase is about 80° away from〈0001〉α direction, and close to〈1120〉α direction. The corresponding lamellar orientation is aligned at the angle of about 10° to growth direction, which is consistent with α-dendrite growth direction according to Blackburn orientation relationship. Therefore, due to the altered growth direction of α phase, the lamellar orientation in Ti-45Al-7Nb alloy is controlled at the G/v ratio of 5×109 K·sm-2.     

常温腐蚀对Al-Si涂层氧化行为的影响

研究了未经 /经常温腐蚀的 DZ1 2 5镍基合金表面 Al-Si涂层的高温氧化行为。结果表明 ,经腐蚀的涂层等温氧化行为发生变化。在初始阶段 ,经腐蚀的试样增重大于未经腐蚀的试样 ,而且经腐蚀的试样的耐高温性能明显下降。氧化皮中主要是 Al2 O3及少量的 Ti O2 .     

激光快速制备Tix Aly-TiN复合涂层

采用激光气体氮化与同步送粉相结合的工艺方法,在Ti-6Al-4V合金表面原位合成了Tix Aly-TiN复合涂层。通过XRD,SEM,OM,EDS,显微硬度测试等手段研究了该复合涂层的物相组成、显微组织、元素分布及显微硬度。结果表明：涂层主要由TiN和Tix Aly 金属间化合物组成;沿激光熔深方向TiN含量下降;Tix Aly 金属间化合物含量上升;涂层无裂纹和孔隙,厚度较均匀,涂层与基体间形成良好的冶金结合;沿激光熔深方向N、Al元素的分布均匀;涂层显微硬度得到显著提高,且从涂层到基体逐渐降低。     

钛合金阳极氧化膜的XPS研究

利用XPS分析了TCA钛合金经阳极氧化处理后,表面氧化膜的成分和结构及其随深度的变化.研究表明,钛合金阳极氧化膜表面为单一的TiO_2,并以晶态和非晶态的形式存在于氧化膜中.随着氧化膜厚度的增加,内部氧化越来越不充分,TiO_2的含量减少,并逐渐出现Ti:O_3、TiO;并且阳极氧化处理明显增厚了表面氧化膜.     

Investigation on induction brazing of profiled cBN wheel for grinding of Ti-6Al-4V

Profiled monolayer cBN wheel was induction brazed for grinding of titanium dovetail slot in this study. Aimed at acquiring a uniform temperature distribution along the profiled surface and reducing the thermal deformation of the brazed wheel, a finite element model was established to investigate the temperature uniformity during induction brazing. A suitable induction coil and the related working parameters were designed and chosen based on the simulation results. Ag-Cu-Ti alloy and cBN grains were applied in the induction brazing experiment. The results showed geometric deformation of the brazed wheel was no more than 0.01 mm and chemical reaction layer were found on the brazed joint interface. Further validation tests were carried out by grinding of Ti-6Al-4V alloy. Compared to the electroplated wheel, the brazed wheel showed better performance such as low specific grinding energy and good ground quality in grinding of Ti-6Al-4V alloy. Abrasion wear was found to be the main failure mode for the induction brazed wheel, while adhesion and grains pull-out were the main failure mode for the electroplated wheel.     

高能超声对Al-5Ti-1B中间合金组织和细化行为的影响

在A l-5Ti-1B中间合金的制备和重熔过程中引入高能超声处理,研究了其对中间合金组织和细化效果的影响。结果发现:在市售A l-5Ti-1B重熔过程中施加超声处理,可以显著改善合金组织和细化作用;制备过程中施加超声处理可以加速氟盐和铝熔体间反应的进行,均匀化组织,提高细化效果;中间合金制备及凝固过程联合超声处理,不仅可以改变TiA l3相的形貌,而且改变了TiB2聚集团的形态,使其变为疏松的鱼卵状,粒子之间不再存在粘连现象,中间合金的细化效果进一步提高。     

Effect of cooling strategies on performance and mechanism of helical milling of CFRP/Ti-6Al-4V stacks

Hole-making for Carbon Fiber Reinforced Plastics(CFRP)/Ti-6Al-4V stacks is crucial for the assembling strength of aircraft structure parts. This work carried out experimental work for helical milling(HM) of the stacks with sustainable cooling/lubrication(dry, MQL and cryogenic)conditions. Cutting forces and temperatures at the CFRP layer, Ti-6Al-4V layer and the interface of stacks were obtained by a developed measuring system. The temperatures in CFRP machining at cryogenic condition varied fro...