Implementation of a single-phase AC/AC converter based on neutral-point-clamped topology

A single-phase ac/ac converter based on neutral-point-clamped scheme is proposed to perform unity input power factor and to provide a stable ac voltage to the critical loads. The ac/dc rectifier part is controlled to generate a unipolar pulsewidth modulation (PWM) waveform on the ac terminal by using four power switches with voltage stress of half the dc-link voltage. The carrier-based current control scheme is employed in the inner control loop to track the line current command. To regulate the dc bus voltage, a proportional-integral (PI) control is adopted in the outer control loop. The dc/ac inverter part of the system with four power switches is employed to generate a stable and clean sinusoidal output voltage to the critical load. The instantaneous current control scheme is used to track the output voltage command. To verify the effectiveness of the proposed control algorithm, the simulation and experimental results based on a laboratory prototype were implemented and discussed.     

Implementation of a three-phase high-power-factor rectifier with NPC topology

A three-phase four-wire power factor corrector based on neutral-point-clamped (NPC) topology is adopted to reduce the current harmonics and increase the input power factor. Using the NPC topology, the voltage stress of power switches can be reduced to the half of the dc-link voltage. With the dc-link voltage controller and the phase locked loop circuit, the balanced and sinusoidal line currents can be drawn from the ac supply system under the balance and unbalance mains voltages. The hysteresis current comparators are adopted in the current control loop to track the line current commands. Three voltage levels are generated on the ac terminal to the neutral point. Simulations and experiments are provided to verify the validity and the effectiveness of the proposed control scheme.     

Half-bridge neutral point diode clamped rectifier for power factor correction

A high power factor rectifier based on neutral point clamped scheme is proposed. The voltage stress of each power semiconductor of the adopted rectifier is equal to the half dc bus voltage instead of full dc link voltage in the conventional switching mode rectifier. The control signals of the power switches are derived from the dc link voltage balance compensator, line current controller, and dc link voltage regulator. The hysteresis current control scheme is employed to draw a clean sinusoidal line current, high input power factor, regulated dc link voltage, and balance capacitor voltages. Three voltage levels are generated on the ac terminal of the adopted rectifier. To verify the proposed operation scheme, performance characteristics are given by the experimental results.     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Space vector modulation strategy for an eight-switch three-phase NPC converter

A three-phase neutral point clamped (NPC) converter is presented for power factor correction and dc-link voltage regulation. A simplified space vector pulsewidth modulation scheme (SVPWM) is adopted to track line current commands. Using a simplified SVPWM algorithm, the calculated time for the time duration of voltage vector is reduced. The adopted NPC converter has less power switches compared with the conventional three-level NPC converter. Only eight power switches and four clamping diodes with voltage stress of half the dc bus voltage are used in the circuit configuration. Based on the proposed control algorithm, a reference voltage vector is generated on the ac terminal for drawing the sinusoidal line currents with unity power factor. Computer simulation and experimental results based on a laboratory prototype are presented to verify the validity and effectiveness of the proposed control strategy.     

Control technique for high power factor multilevel rectifier

Three control techniques for a high power factor multilevel pulsewidth modulation (PWM) rectifier are proposed. The proposed rectifier is based on series connection of full-bridge cell to achieve a high power factor, low current distortion, low voltage stress of power semiconductors and two balanced output voltages. The look-up table is used in the proposed control schemes to reduce the hardware circuit. A capacitor voltage compensator is used to balance two dc capacitor voltages in order to obtain high quality PWM voltage pattern. Based on the proposed control schemes, two-level or three-level PWM pattern can be generated on the ac side of the adopted rectifier. The proposed techniques for a high power factor multilevel rectifier illustrate its validity and effectiveness through the respective simulations and experiments. According to the measured results, the current harmonics drawn from the mains meet the International Electrotechnical Commission (IEC) 1000-3-2 limits     

Single-phase three-level rectifier and random PWM inverter drives

A novel ac/dc/ac converter topology with three-level pulsewidth modulated (PWM) scheme for the single-phase ac/dc rectifier and random PWM scheme for ac drives is proposed. In order to improve the power quality in the single-phase rectifier, a ROM-based (read-only memory) control scheme, based on hysteresis current comparator, region detector, and capacitor compensator, is used to achieve a sinusoidal line current with low current distortion. The control scheme of the adopted three-level rectifier is easy to implement. The blocking voltage of power switches is clamped to half of the dc bus voltage. To reduce the mechanical vibration from an induction motor, random pulse position PWM scheme is adopted to spread the harmonics in a wide frequency range which results in the reduction of torque pulsation in the ac motor drives. Simulation and experimental results based on the laboratory prototype circuit are presented to verify the proposed control scheme     

基于DSC整流器和双闭环PR逆变器的模块化中频静变电源

与传统中频电源相比,模块化中频静变电源具有选用灵活、可靠性高、冗余性好、便于系统维护等优点。中频静变电源整流器在控制母线电压稳定的同时还要实现单位功率因数控制。为此,具体分析了双电流环控制策略,给出了双电流环控制器中电压电流正负序分离原理和双dq锁相环的具体实现方法,即延时信号抵消(DSC)和双闭环准比例谐振(PR)。针对逆变器输出电压基波无差跟踪困难、谐波含量高等问题,采用双闭环多重准PR控制策略,实现中频电压的稳定输出。仿真和试验结果表明,双电流环控制器能同时实现母线电压稳定和单位功率因数控制,采用双闭环多重准PR控制策略的中频逆变器能够输出稳定的中频交流电压。     

Novel single-stage half-bridge series-resonant buck-boost inverter

A novel single-stage half-bridge series-resonant buck-boost inverter (HB-SRBBI) is proposed. The main attribute of the novel inverter topology is the fact that it generates an ac output voltage larger or lower than the dc input one, depending on the instantaneous duty cycle. This property is not found in the classical voltage source inverter (VST), which produces an ac output instantaneous voltage always lower than the dc input voltage. The proposed inverter circuit topology provides the main switch for turn-on at zero-current-switching (ZCS) by an auxiliary resonant cell built before the output choke. A state-space averaging approach is employed to analyze the system. A design example of 500 W ac/dc inverter is examined to assess the inverter performance and it provides high power efficiency above 90.7% under the rated power.     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

Novel single-phase AC/DC converter with two PWM control schemes

A novel single-phase AC/DC converter with two pulsewidth modulation (PWM) schemes is proposed to draw a sinusoidal line current with nearly unity power factor, achieve balanced neutral point voltage and regulate the DC bus voltage. With the aid of neutral point clamped scheme, a three-level voltage pattern is generated on the AC side of the proposed rectifier. To track the tine current command derived from a voltage controller and a phase-locked loop circuit, a hysteresis current control scheme is used in the inner loop control. A capacitor voltage compensator is employed to achieve the balanced neutral point voltage. To investigate the effectiveness of the proposed control scheme, the simulation and experimental results based on a laboratory prototype circuit are performed.     

Low-harmonic three-phase inverters with nonpulsating terminalcurrents

A basic class of three-phase inverters with nonpulsating terminal currents, namely, the four-topology four-inductor four-capacitor class is derived and studied. The expressions of duty-ratios required for low-harmonic dc-to-three-phase-ac conversion, ranges of output voltage variation, and component stresses for given specifications of inverters are derived. The characteristics of inverters include low-harmonic power conversion, low component stresses, variable-frequency variable-amplitude output voltages of values both below and above the dc input value, and the use of minimum number of inductors to achieve nonpulsating terminal currents     

A new power collection architecture for future spacecraft

The generalized tree-like transmission line network system having n layers in total with m-to-1 branch connection at each joint (T-TLNS-n-m) is proposed to replace the traditional series-parallel combined dc networks to automatically accumulate identically distributed power cells into the large amount of useful power for the spacecrafts. The proposed system has the attractive features of simple structure, easy construction and maintenance, and low cost, because two kinds of parts, ac current sources and m-to-1 transmission line (TL) branch connection parts, are used in the whole system. A method of implementing ac current cells having high output impedance is proposed to improve the power collection efficiency of the whole network system. Simulated results show that that low-pass nominal /spl pi/- or T-circuit with high characteristic impedance, which is used for the voltage source to current source converter in the current cell, improves the efficiency of the voltage inverter, filters out the harmonics, and increases the output impedance of the whole current cell.     

火电辅机变频器低压穿越直流电压补偿及其控制

针对火电辅机变频器因厂用电压跌落而触发闭锁,造成发电机组停机的问题,设计了基于变频器直流母线电压补偿的辅助穿越装置。辅机变频器采用直接转矩控制,低压穿越装置主电路采用三重交错并联升压变换器结构,在电压跌落期间维持变频器直流母线电压稳定,同时减小输出电流高频纹波。考虑到并联模块参数差异造成的均流问题,提出在传统电压电流双闭环控制的电压外环加入均流环的解决方法,消除环流,使开关管电流应力更为均衡。由于控制系统具有非线性、强耦合的特点,传统PI控制器存在局限性,所以利用模糊控制算法优化PI控制器参数整定,改善其性能。最后用仿真验证了所提方法的有效性。     

Full control of a PWM DC-AC converter for AC voltage regulation

The design and implement action of a DSP-based fully digital-controlled single-phase pulsewidth modulated (PWM) dc-ac converter for ac voltage regulation is described. The proposed multiloop digital controller (MDC) consists of a current controller, a voltage controller, and a feedforward controller. This MDC was realized using a single-chip digital signal processor (DSP). The PWM gating signals are determined at every sampling instant by the proposed multiloop digital control scheme using a set of detected feedback signals. A software current control; scheme has been developed to achieve fast current control of the PWM inverter and decouple the inductor of the output filter. Experimental results have been given to verify the proposed digital control scheme. The constructed DSP-based PWM dc-ac converter system can achieve fast dynamic response and with low total harmonic distortion (THD) for rectifier type of loads     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Analysis and design of a novel three-phase active power filter

A novel three-phase active power filter is analyzed and designed. A low cost power circuit configuration of the active power filter is proposed, along with a fast peak detector for synthetic sinusoidal generation technique, in order to achieve almost real time compensating current calculation. This technique avoids the use of mains voltage signal in the calculation of reference compensation current. Therefore, the mains current, after compensation, is still a pure sinusoidal waveform, irrespective of the distortion in the mains voltage. Furthermore, a critical value for the magnitude of capacitor voltage on the dc side, and a critical value for the reactor inductance on the ac side have also been derived, for the successful harmonic current tracking in various design applications. Finally, the performance of the active power filter is demonstrated by simulations as well as experimental results     

Stepped Sinewave Inverter

A stepped sinewave dc/ac inverter was analyzed for an inductive load with respect to load current and voltage, harmonics, power factor, and efficiency. This special inverter of high efficiency and low harmonic content is constructed by synthesizing the sinusoidal output by discrete voltage sources, such as storage batteries, solar cell, etc., with electronic switching of the sources at specific time intervals. The switching times are determined for the condition of minimum distortion of the synthesized wave. A 50 W inverter was built and tested to demonstrate this approach.     

输入电压不平衡时的12脉冲自耦变压整流器

在含有较多非线性负载的航空供电系统中常存在三相输入电压不平衡的情况。详细分析了输入不平衡对12脉冲自耦变压整流器(ATRU)的输出电压、输入电流的影响,并提出了采用谐波抑制电抗器(HBR)来抑制谐波电流。分析了工作原理,比较了几种HBR构成方案,研制了一台2kW的演示样机。实验结果表明,谐波抑制电抗器有效抑制了三相输入电压不平衡的影响。