激光器匹配驱动的色散渐变线分析

论述了采用渐变线阻抗变换器对半导体激光器进行匹配驱动时,当考虑渐变线色散影响情况的分析。给出了色散影响的概念、时域的分析计算方法及对三角形、指数形及切比雪夫渐变线的计算结果和分析。     

A resonant DC-DC transformer

The characteristics of a push-pull parallel resonant converter (PPRC) when operated as a DC-DC transformer were investigated theoretically and experimentally. In the DC-DC transformer region, the voltage transfer ratio of the PPRC was found to be practically constant and independent of the input voltage and load. In this mode, all the switching elements operate in the zero voltage switching (ZVS) condition. Another important feature of the proposed DC-DC transformer is the ability to drive it by an arbitrary switching frequency, provided that the latter is lower than the self-oscillating frequency. This permits the synchronization of the converter to a master clock. The analytical expressions for voltage and current stresses, as well as the other key parameters derived, are applied to develop design guidelines for the DC-DC transformer. The proposed topology was tested experimentally on a 100-W unit which was run in the 200-kHz frequency region     

基于更新法估计空闲时间的Inter-DVS算法的优化与实现

动态电压调整(DVS)技术是软件节能技术的另一种形式。由于CMOS电路的能耗和供电电压的平方及频率成正比关系,所以降低供电电压和频率是减少能耗的最有效方法之一。本文首先对DVS的各种算法作了详细的分类分析。然后,以"使用更新法"估计空闲时间的任务间DVS算法为例,采用嵌入式Linux操作系统对其进行了优化。最后,讨论了实现具有动态电压调解功能的嵌入式Linux操作系统的节能方法。     

Table-Aided Design of the Energy-Storage Reactor in DC-to-DC Converters

A new procedure for the selection of magnetic cores for use in energy-storage dc-to-dc power converters that eliminates the need for an automated computer search algorithm and stored data file is presented. The converter configurations included in the procedure are the three commonly encountered single-winding converters for voltage stepup, for current stepup and voltage stepup/current stepup, and for the two-winding converter for voltage stepup/current stepup. For each converter configuration, three types of controllers are considered: constant-frequency, constant on-time, and constant off-time. Using concepts developed from analyses of these converters by considering the transfer of energy by means of an energystorage inductor or transformer, a special table of parameters calculated from magnetic core data is constructed, which leads to a considerably simplified design procedure.     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Minus 35kV Space-Borne Instrument Power Supply

A -35kV power supply has been developed for a plasma experiment on the out-of-ecliptic mission. In addition, an isolation transformer has been developed to provide low voltage power at the -35kV potential. The design features incorporated to produce a spaceflight power supply housed within a 4 × 4 × 2.5 in package are discussed. The supply is powered from an unregulated spacecraft bus and provides a regulated output of -35kV ± 5 percent with less than 0.5 percent ripple over a temperature range -20°C + 60°C. The unit serves as a bias supply with an output current less than 0.5 , ?A. With the supply essentially operating unloaded, 5 percent regulation is achieved by sensing and regulating the first stage of a 12-stage Cockcroft/Walton multiplier. Control of the ac voltage input to the multiplier stack provides the regulation. The isolation transformer utilizes a ferrite u-core with the primary and secondary windings placed on opposite legs for separation. The transformer is encapsulated with the power supply.     

UC3724／UC3725功率MOSFET驱动电路芯片组的应用

高电压、大电流N沟道MOSFET越来越广泛地应用于大功率的电力电子设备中。UNITRODE公司的UC3724／UC3725芯片组通过使用一种独特的调制技术－－通过小型的高频脉冲变压器同时传输信号和功率，实现简单高效的带有电气隔离的MOSFET驱动电路。此电路具有可工作在任意占空比下、实用性强、电路结构简单、响应速度快、输出阻抗小等特点。     

A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

简化起落架噪声相似准则及马赫数比例律

真实飞机部件的气动噪声问题可以通过缩比模型气动声学试验研究,但是必须要遵循合适的相似准则。频率相似准则一般选择Helmholtz数或Strouhal数相似,而声源强度的相似准则在一定的雷诺数范围内通常采用Mach数相似。噪声随来流马赫数的比例律可用于外推风洞试验测量数据到真实飞行条件下,并判断声源类型。在北京航空航天大学D5气动声学风洞中对1/2缩比的LAnding Gear nOise database for civil aviation authority validatiON(LAGOON)简化起落架模型进行了气动声学试验研究。试验结果表明:该起落架模型的噪声频率遵循Helmholtz数相似准则而非Strouhal数相似准则。起落架噪声的马赫数比例律与频率有关,在低频范围内满足6次方关系,而在中高频范围内满足7次方关系。将D5风洞测得的噪声频谱按Helmholtz数相似及相应的马赫数比例律转换后与LAGOON原型试验结果对比,发现两者的测量结果吻合得非常好。     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

小束斑电子束脉冲轰击偏压电源的研制

为了获得一种性价比较高的电子束表面处理技术,采用定频调压电路,研制出一种新型偏压脉冲电源。这种电源由偏压主电路拓扑、偏压变压器和偏压整流滤波电路组成,其中偏压主电路由偏压基值发生电路和偏压脉冲发生电路组成。偏压基值发生电路控制偏压脉冲基值,偏压脉冲发生电路控制偏压脉冲频率和占空比。脉冲偏压电源的脉冲基值、脉冲频率、占空比均连续可调,相应实现脉冲束流的幅值、束流频率和占空比的调节。检测分析了脉冲偏压电源的输出电压波形,带载时的输出束流波形,并观察分析了电子束轰击后钨合金组织变化规律。结果表明所研制的脉冲偏压电源输出电压稳定、可调性好,能满足小束斑脉冲电子束轰击工艺的要求。     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Bipolar nickel-metal hydride batteries for aerospace applications

Electro Energy Inc. (EEI) is developing high power, long life, bipolar nickel-metal hydride batteries for aerospace applications. Bipolar nickel-metal hydride designs allow for high energy and high power designs with a 25 percent reduction in both weight and volume as compared to prismatic and/or cylindrical Ni-MH designs. Utilizing a sealed wafer cell design EEI has demonstrated a 1.2 kW/kg power capability. Prototype designs have achieved 70 Wh/kg. Designs studies show 80 Wh/kg are achievable with EEI's state-of-the-art technology. The sealed wafer cell is the building block for EEI's high power and high voltage bipolar batteries making the assembly easy and significantly lower in cost. Satellite and aircraft batteries are being developed which provide high power and long life. Sealed cells now show excellent rate capability and life. Cells tested in a low earth orbit (LEO) cycle have reached 9000 cycles and continue on test. High power, bipolar battery designs are ideal in applications where using conventional aerospace battery technology would require excessive capacity; weight and volume, thereby reducing usable payload on the vehicle     

Analysis of a PWM-resonant converter

When a parallel resonant tank is excited by a bipolar current pulse train a sinusoidal voltage develops across the tank whose amplitude depends on the duty cycle of the pulse train. An isolated secondary can be derived by applying the tank voltage to an isolation transformer whose magnetizing inductance acts as the resonant inductor of the tank circuit. A dc output voltage is obtained after rectification and filtering of the sinusoidal secondary voltage and regulation is achieved by controlling the duty cycle of the pulse train. The sinusoidal nature of the voltage across the isolation transformer alleviates some of the noise problem associated with parasitic capacitances of an isolation transformer when operated with square voltage waveform. In this work the dc and small-signal analysis of the converter is given and an equivalent small-signal circuit model is derived. Experimental results which confirm the validity of the model are presented.     

Modified Frequency Scaling Algorithm for FMCW SAR Data Processing

This paper presents a modified frequency scaling algorithm for frequency modulated continuous wave synthetic aperture radar （FMCW SAR） data processing. The relative motion between radar and target in FMCW SAR during reception and between transmission and reception will introduce serious dilation in the received signal. The dilation can cause serious distortions in the reconstructed images using conventional signal processing methods. The received signal is derived and the received signal in range-Doppler domain is given. The relation between the phase resulting from antenna motion and the azimuth frequency is analyzed. The modified frequency scaling algorithm is proposed to process the received signal with serious dilation. The algorithm can effectively eliminate the impact of the dilation. The algorithm performances are shown by the simulation results.     

调频连续波SAR改进的频率尺度变换算法(英文)

本文提出了一种调频连续波SAR改进的频率尺度变换算法。调频连续波SAR在运动过程中持续不断地发射和接收信号,这种运动导致了回波信号的伸缩,对波前重建产生了严重的影响。推导了回波信号模型,给出了信号的距离-多普勒域表达式,分析了由于天线不断运动而导致的相位变化与方位向频率之间的关系。改进的频率尺度变换算法补偿了这种相位变化,实现了目标的精确成像,仿真结果表明了分析的正确性和算法的有效性。     

Power Conditioning Systems for High-Power, Airborne, Pulsed Applications

The power conditioning portion of the high-power study that was performed for the Air Force Aeropropulsion Laboratory by the State University of New York at Buffalo is summarized. This effort defines the power conditioning system and critical component developments which will be required to interface the airborne 10-MW to 50-MW sources defined under separate study efforts with certain loads. Power conditioning systems are considered for use with magnetohydrodynamic generators and turbine driven alternators, both conventional and superconducting. The critical components required for each of the power conditioning systems are identified and then analyzed. The component analyses include estimations of development efforts necessary and of specific weights and volumes for components. The primary components considered are transformers (for alternator as well as for inverter use), switches, capacitors, and inductors. Weight algorithms are developed for each of the components. Following the component analyses, subsystems such as inverters and rectifier and filter packages are considered. The data for the various components and subsystems are then utilized for a comparison of the power conditioning techniques to be used with the various power sources. The weights and volumes of power conditioning systems for 8-point designs (8 variations of power, voltage, duty cycle, and total run time) are derived.     

Computer Simulations of Optimum Boost and Buck-Boost Converters

The development of mathematical models suitable for minimum weight boost and buck-boost converter designs are presented. The facility of an augumented Lagrangian (ALAG) multiplier-based nonlinear programming technique is demonstrated for minimum weight design optimizations of boost and buck-boost power converters. ALAG-based computer simulation results for those two minimum weight designs are discussed. Certain important features of ALAG are presented in the framework of a comprehensive design example for boost and buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.