共查询到20条相似文献,搜索用时 132 毫秒
1.
2.
为了研究工艺参数对复合材料缠绕层的温度分布的影响,采用经典热力学理论针对预浸带缠绕过程中的传热机制进行分析;基于缠绕过程中的周期性变化规律,同时以变化的旧层初始温度为传热模型的初始边界条件,构建预浸带缠绕温度分布模型,并通过Matlab编程获得一维热传递模型的精确数值解。理论分析了缠绕初始温度、缠绕速度及芯模温度对缠绕层温度变化的影响。结果表明,对缠绕层温度影响程度依次为芯模温度>缠绕速度>缠绕初始温度;而且无论影响参数如何变化,缠绕层的温度分布始终为内层温度较低,并随着径向位置增大,缠绕层温度也在逐渐升高,直到外层最高温度。此外,通过实验对比分析,说明该温度分布模型满足工程要求,可为缠绕工艺研究提供指导。 相似文献
3.
4.
5.
6.
李勇%肖军%邱伟娟%朱飞 《宇航材料工艺》2002,32(6):19-21
介绍了针对采用高模量碳纤维缠绕时损伤严重而研制的一项新技术。通过无辊浸胶系统和纤维浸胶后烘道加热装置 ,不但降低预浸纱制备和退纱缠绕所造成较大的纤维损伤 ,而且可以实现预浸纱含胶量精确控制及连续浸胶和缠绕 ,同时大大提高了缠绕效率。 相似文献
7.
8.
9.
10.
11.
In the process of composite prepreg tape winding, the compaction force could influence the quality of winding products. According to the analysis and experiments, during the winding process of a rocket motor nozzle aft exit cone with a winding angle, there would be an error between the deposition speed of tape layers and the feeding speed of the compaction roller, which could influence the compaction force. Both a lack of compaction and overcompaction related to the feed-ing of the compaction roller could result in defects of winding nozzles. Thus, a flexible winding sys-tem has been developed for rocket motor nozzle winding. In the system, feeding of the compaction roller could be adjusted in real time to achieve an invariable compaction force. According to exper-iments, the force deformation model of the winding tape is a time-varying system. Thus, a forgetting factor recursive least square based parameter estimation proportional-integral-differential (PID) controller has been developed, which could estimate the time-varying parameter and control the compaction force by adjusting the feeding of the compaction roller during the winding process. According to the experimental results, a winding nozzle with fewer voids and a smooth surface could be wounded by the invariable compaction force in the flexible winding system. 相似文献
12.
针对缠绕复合材料壳体在内压作用下的破坏问题,基于连续损伤介质力学方法,建立了一种缠绕复合材料渐进损伤破坏分析模型。模型中考虑了纤维破坏、基体损伤和纤维/基体开裂3种破坏模式,并针对缠绕复合材料面内剪切非线性的实际,建立了面内剪切非线性模型。通过子程序UMAT将模型嵌入ABAQUS/Standard中,对含缺口缠绕复合材料试件拉伸过程进行了仿真计算,验证了模型的正确性。采用该模型对缠绕复合材料壳体的水压破坏过程进行了仿真分析,结果表明:内压作用下缠绕复合材料的最终破坏是由于纤维断裂导致的,且纤维破坏主要出现在环向层,基体破坏主要出现在纵向层。 相似文献
13.
Placement suitability criteria of composite tape for mould surface in automated tape placement 总被引:2,自引:0,他引:2
《中国航空学报》2015,(5)
Automated tape placement is an important automated process used for fabrication of large composite structures in aeronautical industry. The carbon fiber composite parts realized with this process tend to replace the aluminum parts produced by high-speed machining. It is difficult to determine the appropriate width of the composite tape in automated tape placement. Wrinkling will appear in the tape if it does not suit for the mould surface. Thus, this paper deals with establishing placement suitability criteria of the composite tape for the mould surface. With the assumptions for ideal mapping and by applying some principles and theorems of differential geometry, the centerline trajectory of the composite tape is identified to follow the geodesic. The placement suitability of the composite tape is examined on three different types of non-developable mould surfaces and four criteria are derived. The developed criteria have been used to test the deposition process over several mould surfaces and the appropriate width for each mould surface is obtained by referring to these criteria. 相似文献
14.
15.
李勇%肖军%还大军%文立伟 《宇航材料工艺》2008,38(5)
提出了一种基于两步法的复合材料锥壳螺旋向铺层自动铺带的成型方法,对锥壳螺旋向铺层几何原理进行了分析并对预浸带的预切割进行了设计和验证,对预切割装置进行了原理方案设计并利用CATIA软件进行了自动铺带验证。结果表明:两步法锥壳螺旋向铺带成型技术方案合理可行,预切割装置可以实现预浸带的切割、转录,采用通用铺带头即可以完成螺旋向铺层的自动铺带过程,采用锥壳等厚度铺叠、均匀加压和降低废料率等措施,大大提高制品质量并降低了构件加工成本。 相似文献
16.
17.
18.
19.
研究了16Co14Ni10Cr2Mo钢在冲击载荷下的断裂机制。研究发现,该钢种裂纹钝化方式为角形钝化,裂纹的扩展是高能界面上空穴连接够有选择性的过程,与一次空穴和二次空穴的形成有关。 相似文献
20.
根据柱面的结构特点,提出了面向柱面复合材料结构的自动铺带四轴联动成形方案,并以卧式自动铺带机为例进行分析。以保证铺放头压力线平行于曲面在铺放点的法线和保证铺放速度恒定为原则,根据D-H理论建立柱面固定角度铺放成形时铺带机各关节运动量的计算方法。应用逆运动学理论,对四轴联动铺带成形进行了运动学分析。从四轴联动铺带机的机构与控制、铺放速度、成形效率、方案可行性4个方面进行了深入分析,并进行可视化仿真和实验验证。结果表明应用本文方法,可实现用四轴联动铺带机完成柱面复合材料自动铺放成形,对于铺放成形效率要求不苛求的小批量实验或生产,具有低成本的突出优势。 相似文献