微幅往复走丝微细电解线切割试验研究

 微细电解线切割是一种新型的微细加工技术,适合高精度金属窄缝、窄槽等微细结构的加工,由于加工间隙内电解产物排出困难,容易影响加工精度。为了提高产物排出效率,提出线电极微幅往复走丝促进加工间隙内电解产物排出的方法,改善了加工稳定性,提高了加工精度和加工效率。建立了间隙内电解产物排出效率对加工精度、加工速度影响的数学模型,分析了线电极走丝速度和走丝幅值对间隙内电解产物排出和电解液更新的影响。通过试验研究了线电极的走丝速度和走丝幅值对加工精度和加工效率的影响规律,采用优化参数在厚度为80 μm的钴基弹性合金上进行微槽结构加工,底面粗糙度约为0.45 μm,倒角半径小于8 μm。结果表明线电极轴向微幅往复走丝可以有效地提高加工质量和加工效率。     

航空发动机压气机整体叶盘电解加工技术

介绍了整体叶盘电解加工技术的国内外发展及应用情况,重点阐述了高效电解预加工技术及精密振动电解加工技术的工艺路线、参数制定等关键技术问题。还介绍了与叶型加工相关的主要加工方法,包括机械加工、切割加工等。     

整体叶轮的特种加工方法

本文综述国内外整体叶轮的特种加工技术,重点介绍了等截面电解加工,变截面扭曲叶片整体叶轮的电火花-电解组合、机械靠模仿型电解-电解磨技术及数控展成电解-电解磨新技术。     

微细电解铣削加工模型及实验研究

 对微细电解铣削加工技术进行了深入研究。将分层加工技术应用到微细电解加工过程中,显著改善了加工稳定性;建立了微细电解铣削加工的数学模型;基于电化学刻蚀原理,在线制得直径小至10 μm的圆柱电极;分组实验并验证了加工模型中各参数如：电极直径、加工电压、电解液浓度、铣削层厚度等对微细电解铣削加工精度的影响。通过优化加工参数,成功加工出了深三角结构和四棱台微型腔,形状精度高,加工稳定性好。     

内喷式阴极电解加工整体叶轮叶间通道的间隙特性

本文介绍了在内喷式阴极展成电解加工整体叶轮叶间通道时，加工电压、阴极进给速度、电解液压力和温度对加工间隙的影响，经过对其试验数据所作分析，得出了一些有益的结论，为展成电解加工整体叶轮提供了试验与理论依据。     

微尺度线电极电解加工

微尺度线电极电解是近期出现的一种新加工方法,采用钨丝作为线电极,在加工过程中电极无损耗,通过控制工具电极轨迹可实现微细结构加工。建立了微尺度线电极电解加工模型;通过微尺度线电极叠加微幅振动,促进了加工间隙中电解液更新;针对加工电压、脉冲宽度、脉冲周期和加工速度等影响微尺度线电极电解加工精度的因素进行了参数对比试验,并对加工参数进行了分析和优化。采用电化学腐蚀原理进行微米尺度线电极的在线制作,在线制得直径10 μm和2 μm的线电极,实现了切缝宽度为20 μm以下的复杂微细结构以及切缝宽度为8 μm以下的微螺旋结构。     

叶片型面精密振动电解加工工艺研究

采用电解加工工艺对叶片型面进行加工,可以有效提高发动机叶片加工效率,降低生产成本。针对GH4169G合金叶片型面,开展了精密振动电解加工试验研究。结果表明:高频脉冲电流和阴极机械振动具有改善极间流场特性、降低阳极钝化和阴极的产物吸附的作用,可以大幅改善加工效果;采用参数组加工电压15V、阴极振动频率25Hz、开通角度Ra 150°~195°、脉冲频率3000Hz时,获得最优的型面加工质量,型面轮廓度为-0.012~+0.013mm,表面粗糙度值为0.51μm,证明精密振动电解加工工艺满足叶片型面的加工要求。     

钛合金小余量叶片脉冲电流电解加工

脉冲电流电解加工可以改善流场,提高加工稳定性,有利于进行小间隙加工,从而提高加工精度。本文介绍了脉冲电流电解加工钛合金小余量叶片的情况,并且取得了较好的效果。     

超短脉冲微细电解加工实验研究

介绍了利用超短脉冲电源进行微细电解加工实验的原理与装置,分析了影响微细电解加工的几个主要因素及影响趋势.并研究了微细电极的在线制作,发现采用铜锌合金材料可以很容易地加工出直径10μm左右,长径比大于50的微细电极,且电极的圆柱度很好.     

喷射液束电解-激光复合加工工艺试验研究

喷射液束电解 激光复合加工是一项新探索的加工技术,其特点是既发挥激光加工的高效率,又借助喷射电液束的冷却、冲刷、电解作用而实现在线去除再铸层。基于该加工原理的分析,在对激光电解液中衰减特性研究的基础上,研制了试验系统并对不锈钢片进行了打孔工艺试验。试验结果表明,应用液压1.5 MPa、浓度18%的NaNO₃电解液的喷射液束电解-激光复合加工可实现再铸层减少90%以上。通过对打孔形貌的对比以及加工工艺规律的初步分析,揭示了喷射液束电解-激光复合加工以激光加工为主,电解加工辅助去除再铸层的加工原理,证实了该复合加工工艺的可行性,可望在航空航天领域得到广泛工程应用。     

现代特种加工技术的发展

简述了特种加工的技术特点和未来发展趋势,分别论述了高能束流加工、电火花加工、电解加工、物料切蚀加工和复合加工技术的概念、特征与应用状况。     

超细晶硬质合金加工机理及加工性能

围绕超细晶硬质合金精密磨削加工、在线电解修整磨削加工、电火花加工、超声复合加工、激光复合加工等加工方法,系统综述了超细晶硬质合金的加工机理和加工性能,并展望了超细晶硬质合金高效精密加工未来的研究重点。     

基于超纯水电解加工的水解离机理研究

介绍了一种以超纯水为电解液的电解加工工艺方法,即超纯水电解加工技术.研究了阳离子交换膜在超纯水中的水解离机理及工作特性,分析其在超纯水电解加工过程中的作用机理,并进行了水解离试验研究.结果表明：电流密度达到了3.7 A/cm^2,电场强度约为2 MV/m,已进入微细电解加工去除材料要求范围,为超纯水微细电解加工的应用奠定了基础.     

单晶硅电火花线切割表面损伤层形成机理

 为了研究单晶硅电火花线切割(WEDM)表面损伤层的损伤形式和形成机理,以电火花线切割加工后的单晶硅表面为研究对象,采用表面形貌观察分析及择优腐蚀方法研究了单晶硅经过电火花线切割后的加工表面.研究结果表明单晶硅经电火花放电加工后表面损伤形式分为4种:热损伤、应力损伤、热与应力综合作用损伤及电解/电化学腐蚀损伤.热损伤使得硅表面形成多晶或非晶硅;应力损伤使硅表面产生裂纹;热与应力综合作用会产生小孔效应,且随着放电功率密度的增加,小孔会明显增多;电解/电化学作用会加快损伤区域及杂质元素富集区域的腐蚀.     

微小孔电化学去毛刺试验研究

采用电化学方法对不锈钢管壁上钻削的微小孔与不锈钢管内壁相贯处难到达区域的毛刺进行去除。实验研究了加工时间、电解液成分与浓度、电解液流动方式对微小孔毛刺去除质量的影响以及相应条件下阴阳极极间电压的变化规律。研究结果表明:在优选的加工工艺参数条件下,可有效地去除微小孔毛刺。     

Wire electrochemical machining with axial electrolyte flushing for titanium alloy

Titanium and its alloys have found very wide application in aerospace due to their excellent characteristics although their processing is still a challenge. Electrochemical machining is an important issue in the fabrication of titanium and titanium alloys. Wire electrochemical machining (WECM) is mainly used for workpiece cutting under the condition of different thickness plates. It has a great advantage over wire electro-discharge machining, which is the absence of heat-affected zone around the cutting area. Moreover, the wire electrode in WECM could be used repetitively because it is not worn out. Thus, much attention has been paid to WECM. The effective way of removing electrolysis products is of importance to WECM. In this paper, the axial electrolyte flushing is presented to WECM for removing electrolysis products and renewing electrolyte. The Taguchi experiment is conducted to optimize the machining parameters, such as wire feedrate, machining voltage, electrolyte concentration, etc. Experimental results show that WECM with axial electrolyte flushing is a promising issue in the fabrication of titanium alloy (TC1). The feasibility of multi-wire electrochemical machining is also demonstrated to improve the machining productivity of WECM.     

Aviation-oriented Micromachining Technology-Micro-ECM in Pure Water

This article proposes a precise and ecofriendly micromachining technology for aerospace application called electrochemical machining in pure water （PW-ECM）. On the basis of the principles of water dissociation, a series of test setups and tests are devised and performed under different conditions. These tests explain the need for technological conditions realizing PW-ECM, and further explore the technological principles. The results from the tests demonstrate a successful removal of electrolytic slime by means of ultrasonic vibration of the workpiece. To ensure the stability and reliability of PW-ECM process, a new combined machining method of PW-ECM assisted with ultrasonic vibration （PW-ECM/USV） is devised. Trilateral and square cavities and holes as well as a group of English alphabets are worked out on a stainless steel plate. It is confirmed that PW-ECM will be probably an efficient new aviation precision machining method.     

ELID磨削硬脆材料精密和超精密加工的新技术

金属基超硬磨料砂轮在线电解修整（ＥｌｅｃｔｒｏｌｙｔｉｃＩｎｐｒｏｃｅｓＤｒｅｓｉｎｇ,简称ＥＬＩＤ）磨削技术是国外近年发展起来的一种硬脆材料精密和超精密加工新技术。本文介绍了ＥＬＩＤ磨削技术的基本原理、工艺特点和国内外研究应用情况。应用ＥＬＩＤ磨削技术,可对工程陶瓷等硬脆材料实现高效率磨削和精密镜面磨削     

Surface-improvement mechanism of hybrid electrochemical discharge process using variable-amplitude pulses

Superalloys are commonly used in aircraft manufacturing; however, the requirements for high surface quality and machining accuracy make them difficult to machine. In this study, a hybrid electrochemical discharge process using variable-amplitude pulses is proposed to achieve this target. In this method, electrochemical machining (ECM) and electrical discharge machining (EDM) are unified into a single process using a sequence of variable-amplitude pulses such that the machining process realizes both good surface finish and high machining accuracy. Furthermore, the machining mechanism of the hybrid electrochemical discharge process using variable-amplitude pulses is studied. The mechanism is investigated by observations of machining waveforms and machined surface. It is found that, with a high-frequency transformation between high- and low-voltage waveforms within a voltage cycle, the machining mechanism is frequently transformed from EDM to pure ECM. The critical discharge voltage is 40 V. When pulse voltages greater than 40 V are applied, the machining accuracy is good; however, the surface has defects such as numerous discharge craters. High machining accuracy is maintained when high-voltage pulses are replaced by low-voltage pulses to enhance electrochemical dissolution. The results indicate that the proposed hybrid electrochemical discharge process using variable-amplitude pulses can yield high-quality surfaces with high machining accuracy.