共查询到18条相似文献,搜索用时 109 毫秒
1.
针对光纤环的热致非互易误差的补偿方法进行研究,并通过仿真分析与实验验证,证明了某种光纤环尾纤长度与光纤环热致非互易误差之间的关系。根据等效介质理论和Mohr理论,建立了光纤环热致非互易相位误差仿真分析模型,并利用该模型计算了不同温度环境条件下,某类型光纤环顺逆时针方向光纤长度发生变化时,陀螺仪输出的全温零位漂移的变化量。仿真及实验结果表明,在1℃/min温变速率条件下,总长约800m的光纤环圈顺逆时针方向光纤长度相差约0.5m时,光纤环全温零位漂移量缩小了0.4(°)/h。研究结果得出了针对此类型的光纤环,当光纤环尾纤每减少0.5m,其热致非互易相位误差减小0.4(°)/h的规律。该项研究成果为后续优化光纤环的全温精度奠定了基础。 相似文献
2.
3.
4.
外界温度场作用下,光纤环温度变化和热应力是引起光纤陀螺非互易误差的主要原因。分析了光纤陀螺热致漂移的数学模型,基于该模型仿真研究了对光纤环以恒定功率加热随后转入平稳状态扰动因素下陀螺的输出特性。为验证模型准确性,选用3个光纤环搭建光纤陀螺系统,并对陀螺零偏变化特性进行了测试。测试结果表明,各陀螺零偏测试值与模型计算值间的误差不超过8%,实验结果与模型能够较好符合,该研究结果对高精度光纤陀螺的设计具有重要指导意义。 相似文献
5.
6.
为了提高光纤陀螺温度补偿精度,采用Mohr理论建立了光纤环圈的热传递模型,准确分析了光纤环圈内部的温度变化和分布情况,计算得到了光纤环圈的Shupe误差。根据Shupe理论误差和陀螺仪输出的相关性分析,得到了最优的光纤环圈热传递参数。根据热传递参数建立了光纤陀螺温度补偿模型,完成了光纤陀螺的实时温度补偿,实际补偿后光纤陀螺仪变温精度提高了约3.4倍。 相似文献
7.
8.
9.
用于光纤陀螺的光纤环缠绕工艺研究 总被引:1,自引:0,他引:1
光纤陀螺中光纤环是一个重要部件,不仅可以通过调整光纤环结构参数,如光纤环面积、光纤长度,来提高光纤陀螺精度,同时环境因素,如温度、应力也将通过改变光纤环中光纤的物理参数,引起非互易性相位噪声,从而降低光纤陀螺精度。 相似文献
10.
针对当前缺乏有效的光纤环温度性能评价方法确保光纤陀螺整表全温精度的问题,搭建了光纤环温度测试系统,提出了一种光纤环评价方法。该方法不但能够评价光纤环的温度性能,而且能够反映陀螺整表的全温精度。根据测试结果,分析了基于Shupe系数的线性误差和线性补偿后的非线性误差。其中,前者代表了光纤环的温度灵敏度,后者代表了光纤环的可补偿程度,两者共同构成了光纤环的评价指标。利用该测试系统测试了数十只同一尺寸的光纤环,非线性误差小于0.022(°)/h,补偿后整表的全温零偏稳定性小于等于0.01(°)/h(-40℃~+60℃,1℃/min),为后续高精度光纤陀螺的生产提供了一定的指导。 相似文献
11.
12.
13.
14.
JIA Ming YANG Gongliu School of Instrumentation Science Opto-electronics Engineering Beihang University Beijing China 《中国航空学报》2011,24(5):640-647
Optical fiber coil winding model is used to guide proper and high precision coil winding for fiber optic gyroscope (FOG) application. Based on the large-deformation theory of elasticity, stress analysis of optical fiber free end has been made and balance equation of infinitesimal fiber is deduced, then deformation equation is derived by substituting terminal conditions. On condition that only axial tensile force exists, approximate curve equation has been built in small angle deformation scope. The comparison of tangent point longitudinal coordinate result between theory and approximation gives constant of integration, and expression with tangent point as origin of coordinate is readjusted. Analyzing the winding parameters of an example, it is clear that the horizontal distance from the highest point of wheel to fiber tangent point has millimeter order of magnitude and significant difference with fiber tension variation, and maintains invariant when wheel radius changes. The height of tension and accurate position of tangent point are defined for proper fiber guide. For application to fiber optic gyroscope, spiral-disc winding method and nonideal deformation of straddle section are analyzed, and then spiral-disc quadrupole pattern winding method has been introduced and realized by winding system. The winding results approve that the winding model is applicable. 相似文献
15.
研究了固化温度对苎麻纤维增强复合材料力学性能的影响,同时对比研究了平纹苎麻织物、单向苎麻纤维和单向玻璃纤维增强复合材料的力学性能.结果表明:环氧树脂3233分别在120℃,140℃和l80℃固化2h后,其拉伸性能和弯曲性能没有明显的变化;而基于环氧树脂3233的苎麻纤维增强复合材料在120℃和l40℃固化2h后力学性能相当,但是在180℃固化2h后,强度明显减小,模量变化不大;单向苎麻纤维增强复合材料的力学性能要远远大于平纹苎麻织物增强复合材料的力学性能,如单向苎麻复合材料uRamie-3233-120的压缩强度和压缩模量分别为154.0 MPa和35.6 GPa,而苎麻织物增强复合材料fRamie-3233-120分别为95.0 MPa和9.2 GPa;玻璃纤维增强复合材料的强度也会高明显高于苎麻纤维增强复合材料的强度. 相似文献
16.
17.
LU Xiao-jun ZHANG Qi* School of Materials Science Engineering Bejing University of Aeronautics Astronautics Beijing China 《中国航空学报》2006,19(Z1)
In this paper, the effects of test temperatures and time on the impact damage behavior of unidirectional carbon fiber reinforced epoxy resin composites, immersed in pure water, on a pendulum impact tester, was studied. The results show that immersion in liquids has a significant effect on the impact resistance of the unidirectional composite material. It is obvious that after immersion, the mass of the material increases. The fracture initiation forces as well as the fracture initiation energy decrease as the immersion time lengthens. Moreover, the higher the temperature and the longer the time are, the more the crack propagation energy and the ductility index will be. Immersion makes the fracture mode change from the dominant fiber fracture into dominant delamination. All in all, immersion decreases the impact resistance of the composites and causes the fracture mode to change. 相似文献
18.
石英增强聚酰亚胺树脂基复合材料是一种非均匀的各向异性材料,其加工性能高度依赖于纤维铺层方向与加工进给方向所成角度,即纤维方向角。本文通过一系列不同纤维方向角的干切削和超低温冷却铣削实验,研究了纤维方向角对表面形貌、表面粗糙度、铣削力及刀具磨损的影响。结果表明:不同纤维方向角,剪应力形式不同,切削断屑形式也不同。纤维方向角为锐角时铣削表面质量均良好,但当纤维方向角增大到90°时,切削表面质量下降,切削力变化幅度增大。相同铣削时间内,在干切削工况下,刀具磨损严重,涂层脱落面积约为测量面积的70%;而在低温切削工况下,涂层未遭到严重破坏,刀具仍处于稳定磨损阶段,刀具耐用度优于干切削工况。 相似文献