基于等效元素法的机电作动器传动机构动力学建模与分析

目前机电作动器传动机构存在刚体数目多、传动链长、动力学模型难以建立的问题。通过引入规范化的动力学建模方法——集中质量等效元素法,建立了某机电作动器传动机构的动力学模型,包括等效系统质量阵、等效系统力系和系统自由坐标与广义坐标之间的雅克比关系阵,并得到了其解析动力学方程;结合方程在ADAMS平台进行动力学逆求解仿真,得到了30°大行程位移信号和8Hz频率信号两种工况下的系统载荷响应曲线。随着负载转动惯量增加,电机动载系数达到1.34,丝杠动载系数达到1.55;外部负载不变时,随着驱动信号幅值增加,电机动载最大系数达到1.23。分析表明随着机电作动器系统外部惯性负载及系统运动速度的提高,由外部惯性负载及自身传动机构产生的动载效应明显,为机电作动器传动机构优化设计提供了理论依据。     

垂尾抖振主动控制的压电作动器布局优化

为了提高压电作动器垂尾抖振主动控制系统的控制性能,提出一种基于输出可控性的压电作动器优化准则。使用压电驱动载荷等效方法建立压电纤维复合材料（MFC）压电作动器力学模型,并建立了带MFC压电作动器垂尾结构模型的动力学方程。在模态可控性和模态价值理论的基础上,提出考虑剩余模态影响的压电作动器优化目标函数。针对垂尾结构的前5阶模态使用遗传算法优化得到压电作动器的布局方案,使用线性二次高斯（LQG）最优控制方法控制垂尾的抖振响应。仿真结果表明,本文优化得到的布局方案比用其他方法能更好地均衡系统的模态可控性,减小剩余模态的影响,获得更好的垂尾抖振响应控制。     

基于EHA的多轮系飞机刹车系统的建模与仿真

介绍了一种采用电动静液作动器(EHA)代替原有液压作动机构的飞机多轮系防滑刹车系统,在重点分析EHA的系统组成原理和工作特性的基础上.建立了EHA及多轮系飞机刹车系统的数学模型,采用Matlab/simulink对其进行仿真.仿真结果表明:所建立的模型基本正确,结果与真实刹车基本吻合;采用EHA代替液压系统能极大改善飞机刹车性能.     

压电智能反射面静态形状控制与作动器位置优化

为了提高反射面的精度,建立了压电智能反射面的形状控制模型,对该结构的力学建模方法、形状控制方法和作动器优化配置算法进行了研究。首先,将蜂窝夹层结构的压电智能反射面等效为多层复合板,根据虚功原理推导了结构的有限元方程。然后,根据建立的有限元方程,推导了反射面变形的均方根误差与作动器控制电压的关系式,以均方根误差最小为优化目标,建立了形状控制优化模型,将作动器控制电压的优化转化为约束优化问题的求解。最后,采用模拟退火算法对压电作动器进行了优化配置。为了验证形状控制的可行性及优化算法的有效性,以300mm口径的平面压电智能反射面为例进行仿真,分析结果表明,通过压电作动器的控制,可以使反射面的重力变形误差减小97%以上,对于给定数目的作动器,通过模拟退火算法优化,可使其布置在最佳的位置。     

考虑扰动输入/性能输出分布时作动/传感器配置优化

 针对结构振动控制问题，提出了一种考虑扰动输入/性能输出分布信息时作动/传感器的优化配置准则。在降维的模态坐标下建立状态空间形式的结构动力学方程，通过Lyapunov方程求解扰动和作动器的能控性Gramian矩阵，并利用矩阵奇异值分解获得扰动的能控性方向和作动器的能控性方向，通过同时最大化作动器对结构的作动能力以及作动器的能控性方向与扰动的能控性方向的一致性来确定作动器的最优位置。类似思想用于确定传感器的最优位置。以采用压电片为作动器的悬臂梁为例阐述了新准则的应用。     

基于模型的系统工程在作动器领域的应用研究

以飞机作动器产品为研究对象,通过条目化需求分析,将产品设计过程进行逐级分解。利用AMESim、AN-SYS系列软件等仿真工具,建立从部件到产品的各级仿真模型,并开展仿真分析工作,通过对仿真分析过程和结果的分析,探索了基于模型的系统工程方法的工作流程,总结了飞机液压作动器基于模型的系统工程方法的应用基础。     

DDV作动器余度数字伺服系统工程设计与实现

 介绍一种直接驱动阀（DDV）式作动器的余度数字式伺服系统设计与实现,描述了系统的余度配置、设计思想及组成,建立了DDV作动器的结构参数化模型及数字伺服回路的模型,并进行了仿真,分析了作动器动静态特性、采样频率及监控器的设计性能。最后,采用快速原型实时仿真,对余度数字式伺服系统完成了的性能试验验证,结果表明系统性能令人满意。     

电流变柔性微致动器致动过程研究

利用电流变液体阻尼阀效应设计了原型电流变柔性微致动器,建立了相应的力学模型,进行了柔性微致动器致动过程实验研究和三维致动过程的计算机图形仿真,并对电流变柔性微致动过程的位移、速度和加速度等运动学和动力学特征进行了分析研究。     

航空发动机反推作动器楔形缓冲结构研究

为了削弱航空发动机反推作动器在展开过程末端的强烈机械冲击，将楔形液压缸缓冲结构应用于该反推作动器。本文建立了该反推作动器节流缓冲的数学模型和Simulink仿真模型，对该作动器在缓冲过程中的速度特性和时间特性进行仿真，分析了速度和压力对其缓冲特性的影响。研究结果表明，本文提出的楔形缓冲结构有助于减小航空发动机反推作动器活塞与筒体的碰撞速度，能有效削弱工作末端的冲击；在保证运行速度不变的前提下，可以通过适当降低系统的通油压力来提高反推作动器的节流缓冲效果。     

柔性铰链放大式超磁致伸缩致动器磁弹耦合模型

针对超磁致伸缩致动器(GMA)输出位移有限的问题,采用柔性铰链放大机构放大GMA输出位移,利用材料力学理论、拉格朗日动力学方程和有限元法对柔性铰链放大机构的位移放大倍数、动力学特性进行了分析.结合Jiles-Atherton(J-A)模型和二次畴转模型建立了柔性铰链放大式GMA的磁弹耦合模型,并在软件AMESim&Simulink联合仿真环境中进行了数值仿真.制作了柔性铰链放大式GMA样机,对其进行了动态性能实验,仿真和实验表明:经过放大,柔性铰链放大式GMA输出位移可以达到0.4mm;频带宽超过100Hz;所建立的磁弹耦合模型是有效的.      

烧蚀反应动力学参数的确定

本文提出了一种理论模型与实验相结合确定碳基材料烧蚀反应动力学参数(活化能和指前因子)的方法。首先建立了碳基材料热化学烧蚀的湍流边界层模型,运用数值方法对边界层守恒方程组、表面烧蚀和固相热传导进行耦合求解,计算过程中不需要事先假设烧蚀的控制类型。其次,在电弧加热器中模拟火箭发动机喷喉的烧蚀环境进行烧蚀材料与氧化性气体反应的烧蚀实验。最后,运用所建立的模型和在电弧加热器上的实验结果进行预测比较,确定烧蚀反应的动力学参数。作为实例,确定了石墨与CO_2的烧蚀反应的动力学参数。     

Prediction of Boundary Layer Transition Based on Modeling of Laminar Fluctuations Using RANS Approach

This article presents a linear eddy-viscosity turbulence model for predicting bypass and natural transition in boundary layers by using Reynolds-averaged Navier-Stokes (RANS) equations. The model includes three transport equations, separately, to compute laminar kinetic energy, turbulent kinetic energy, and dissipation rate in a flow field. It needs neither correlations of intermittency factors nor knowledge of the transition onset. Two transition tests are carried out: flat plate boundary layer under zero ...     

Integrated power and attitude control with two flywheels

Energy storage and attitude control are two distinct subsystems of the typical satellite. Energy storage is provided using batteries and active attitude control is accomplished with control moment gyroscopes or reaction wheels. A system mass savings can be achieved if these two subsystems are combined using multiple flywheels for simultaneous kinetic energy storage and momentum transfer. This paper develops, simulates, and experimentally demonstrates the control algorithms to accomplish integrated power and single-axis attitude control using two flywheels.     

A linear ADRC-based robust high-dynamic double-loop servo system for aircraft electro-mechanical actuators

Compared with traditional hydraulic actuators, an Electro-Mechanical Actuator(EMA)is small in size and light in weight, so it has become more widely used. Aerodynamic load on aircraft control surface varies dramatically, and a change of flight environment leads to uncertainties of motor parameters. Therefore, high-dynamic response and strong anti-disturbance capability of an EMA are of great significance for aircraft rudder control and flight attitude adjustment. In order to improve dynamic response and disturbance rejection of an EMA and simplify control parameters tuning, a robust high-dynamic servo system based on Linear Active Disturbance Rejection Control(LADRC) is proposed for an EMA employing a Permanent Magnet Synchronous Motor(PMSM).Firstly, total disturbances of the EMA are analyzed, including parameter uncertainties, load variation, and static friction. A disturbance observer based on a reduced-order Extended State Observer(ESO) is designed to improve the anti-interference ability and dynamic performance. Secondly, the servo control architecture is simplified to a double-loop system, and a composite control of position and speed with acceleration feed-forward is presented to improve the EMA frequency bandwidth.Thirdly, the ideal model of the EMA is transformed into a simple cascade integral form with a disturbance observer, which makes it convenient to analyze and design the controller. Robustness performance comparisons are realized in frequency domain. Finally, simulation and experimental results have verified the effectiveness of the proposed strategy for EMAs.     

基于Reynolds平均的高超声速二方程湍流模型

 在Reynolds平均的框架下推导了可压缩湍流Reynolds应力方程和湍动能方程。根据一定的假设和尺度分析简化并封闭了所推导的湍动能方程。在均匀湍流假设下,湍动能耗散率可分解成可压缩性耗散和旋度耗散,并对其中的可压缩性耗散进行了封闭;同时认为旋度耗散不受可压缩性影响,直接引用传统的Reynolds平均不可压缩湍动能耗散率模型方程。由此构造了适用于高马赫数的二方程可压缩湍流模型。应用所发展的模型计算了高超声速平板绕流,并与若干现有模型的计算、实验与半经验公式的计算结果进行了对比,验证了所发展的模型。在此基础上,通过对压缩拐角的高超声速湍流的数值模拟,对所发展的湍流模型,以及若干现有模型进行了对比,显示了不同湍流模型及可压缩性修正在计算壁面压力分布和热流分布上的特点,说明了湍流模型可压缩修正的必要性,得到了所发展模型的计算结果最接近实验结果的结论。     

基于灰色补偿反步法的机动指令跟踪控制

基于三自由度飞行动力学模型和运动学模型,提出了一种带有灰色补偿的反步(Back-stepping)控制方法,以实现某些预定的战术机动动作。首先,将飞行动力学模型和运动学模型分解成3个轴方向的相对简单的子系统;然后,针对3个子系统采用反步法分别设计出模型中没有干扰时的控制律,并采用GM(0,N)预测模型对不确定部分的模型参数进行辨识,进一步根据估计出的参数设计灰色补偿控制律;最后,根据3个子系统设计出的控制律解算出同时满足3个子系统渐进稳定的控制输入,这样使得整个系统渐进稳定。仿真结果表明,GM(0,N)预测模型能精确预测不确定模型参数,该算法能够高效实现预定的战术机动动作。     

Multiple-model estimation with variable structure- part VI: expected-mode augmentation

A new class of variable-structure (VS) algorithms for multiple-model (MM) estimation is presented, referred to as expected-mode augmentation (EMA). In the EMA approach, the original set of models is augmented by a variable set of models intended to match the expected value of the unknown true mode. These models are generated adaptively in real time as (globally or locally) probabilistically weighted sums of mode estimates over the model set. This makes it possible to cover a large continuous mode space by a relatively small number of models at a given accuracy level. The paper presents new theoretical results for model-set design, a general formulation of the EMA approach, along with theoretical analysis and justification, and three algorithms for its practical implementation. The performance of the proposed EMA algorithms is evaluated via simulation of a generic maneuvering target tracking problem.     

Source free unsupervised domain adaptation for electro-mechanical actuator fault diagnosis

A common necessity for prior unsupervised domain adaptation methods that can improve the domain adaptation in unlabeled target domain dataset is access to source domain dataset and target domain dataset simultaneously. However, data privacy makes it not always possible to access source domain dataset and target domain dataset in actual industrial equipment simultaneously, especially for aviation component like Electro-Mechanical Actuator (EMA) whose dataset are often not shareable due to the data copyright and confidentiality. To address this problem, this paper proposes a source free unsupervised domain adaptation framework for EMA fault diagnosis. The proposed framework is a combination of feature network and classifier. Firstly, source domain datasets are only applied to train a source model. Secondly, the well-trained source model is transferred to target domain and classifier is frozen based on source domain hypothesis. Thirdly, nearest centroid filtering is introduced to filter the reliable pseudo labels for unlabeled target domain dataset, and finally, supervised learning and pseudo label clustering are applied to fine-tune the transferred model. In comparison with several traditional unsupervised domain adaptation methods, case studies based on low- and high-frequency monitoring signals on EMA indicate the effectiveness of the proposed method.     

Concepts for position and load control for hybrid actuation in primary flight controls

Moving towards the More Electric Aircraft, a hybrid actuator configuration, in which an electromechanical actuator (EMA) and an electrohydraulic servoactuator (EHSA) operate on the same control surface, provides an opportunity to introduce electromechanical actuators into primary flight controls. Besides the operation in active/passive or active/active mode, an “active/no-load” mode is promising. In this mode the EMA is controlled such that it actively follows the movement of the control surface without carrying external air loads, thereby reducing power dissipation compared to active/active mode and failure transients compared to active/passive mode. However, force fighting will occur if both actuators are actively controlled. In this paper, control concepts for a hybrid configuration, extending the original actuator control loops, are presented, enabling active/active as well as active/no-load operation. Nonlinear as well as linear models for an EMA, an EHSA, and a control surface structure are derived from technical data for an airworthy EHSA and combined to a model of the hybrid configuration. These models are used for matching of actuator dynamics and simulation of the developed control laws. For active/active mode, maximum force fighting between the actuators is reduced from about 500% to 7% of the stall load. For active/no-load mode, a force control loop is added to the EMA control, causing the EMA to follow movements of the control surface such that the external loads on the EMA are zero in steady-state. Force fighting is reduced to 30% of the stall load.     

基于质量矩技术的机动弹头再入仿真研究

对基于质量矩技术的机动弹头再入性能进行了探讨。首先建立了弹头的空间运动数学模型;然后在此基础上根据再入段特性对运动方程作了适当简化并计算了弹头内部质量块分别处于静止、瞬时置位、线性平动这三种运动状态下的落点参数;最后分析比较了质量块运动的变化对机动范围的影响。仿真结果表明了质量矩技术作为弹头再入机动控制方式的可行性。