共查询到15条相似文献,搜索用时 125 毫秒
1.
姚草根%吕宏军%贾新潮%张绪虎%王琪 《宇航材料工艺》2005,35(2):10-13
简要综述了金属热防护系统的国外研究进展,重点介绍了美国高温合金热防护系统材料与结构以及钛合金热防护材料与结构的研究概况,并对国内情况作了一些简介。指出金属热防护系统是下一代重复使用运载器大面积表面热防护的第一方案。 相似文献
2.
重复使用金属热防护系统研究进展 总被引:1,自引:1,他引:0
综述了金属热防护系统的国外研究最新进展,重点介绍了国内相关研究和试验的最新情况.指出金属热防护系统仍是下一代重复使用运载器大面积表面热防护系统的优选方案之一. 相似文献
3.
介绍了一种新型金属热防护系统ARMORTPS的概念设计和分析方法。ARMORTPS是NASA Langley研究中心在X-33金属TPS基础设计出的一种可适应的、坚固的、金属性的、可操作的、可重复使用的新型热防护系统,它覆盖在运载器低温储箱外表面,与低温储箱壁板进行了一体化设计。介绍了ARMOR TPS的设计思想和设计准则。详细阐述了ARMOR TPS的载荷工况、热分析与结构分析有限元模型。介绍了确定TPS几何尺寸的循环迭代法。ARMOR TPS的设计理念和分析方法无疑对我国自行研发高M数飞行器热防护系统具有一定的借鉴和指导作用。 相似文献
4.
史丽萍%李垚%赫晓东 《宇航材料工艺》2005,35(3):21-23
简述国外几代金属热防护系统的发展概况,并论述金属热防护结构的组成特点,对金属热防护系统与其他传统热防护系统的优缺点进行比较,指出金属热防护系统必将是各种类型可重复使用航天飞行器大面积防热的最佳选择。 相似文献
5.
金属热防护系统设计的有限元分析 总被引:3,自引:0,他引:3
对可重复使用运载飞行器金属热防护系统进行了有限元分析,计算发现超耐热合金防热结构中下层蜂窝夹芯板的存在会增加结构的质量,但是并不会提高绝热性能,因此改进型防热系统取代了超耐热合金防热系统。比较分析了板间缝隙宽度和辐射率对防热结构底部最大温度的影响,表明减小板间缝隙是消除缝隙辐射的最好办法。分析了模拟条件对热防护系统尺寸设计的影响:初始温度为0℃时比为40℃时最大可以减少17%的厚度和7.7%的质量;考虑热损失厚度最小可以降低26%,质量最小可以降低7%。 相似文献
6.
7.
8.
简述了国外可重复使用运载器的研究现状及发展趋势,详细介绍了美国下一代可重复使用运载器Micro—X概念验证机的热防护材料及设计。 相似文献
9.
介绍了国外用于高超音速飞行器上的金属热防护系统的发展历程,以及先进金属热防护系统的研究状况,并阐述了金属热防护系统的发展方向。 相似文献
10.
11.
Accelerated Landweber iteration based control allocation for fault tolerant control of reusable launch vehicle 总被引:1,自引:0,他引:1
This paper presents a novel Fault Tolerant Control(FTC) scheme based on accelerated Landweber iteration and redistribution mechanism for a horizontal takeoff horizontal landing reusable launch vehicle(RLV). First, an adaptive law based on fixed-time non-singular fast terminal sliding mode control(NFTSMC), which focuses on the attitude tracking controller design for RLV in the presence of model couplings, parameter uncertainties and external disturbances, is proposed to produce virtual control co... 相似文献
12.
Continual improvement of avionic built-in test (BIT) is critical to mission readiness and capability. This paper discusses how test program set (TPS) and relational database (RDB) technologies can be used for this purpose. Important aspects for continually improving avionic BIT and TPS operation are discussed 相似文献
13.
针对可重复使用运载器(RLV)原场返回过程中所面临的轨迹回转问题,提出了一种在亚轨道高度进行姿态调整并使飞行轨迹回转、指向发射场方向的机动方法.在RLV与上面级分离之后,利用RLV自身推力抵消背离发射场速度,最终使RLV飞行方向指向发射场并进入再入返回阶段.采用连续推力方案,利用最优控制理论推导得出满足轨迹回转终端要求的机动指令.仿真结果表明,该方法能够实现RLV与上面级分离后轨迹迅速回转,可为之后的返回原发射场提供保障. 相似文献
14.
15.
An autonomous approach and landing (A&L) guidance law is presented in this paper for landing an unpowered reusable launch vehicle (RLV) at the designated runway touchdown.Considering the full nonlinear point-mass dynamics,a guidance scheme is developed in threedimensional space.In order to guarantee a successful A&L movement,the multiple sliding surfaces guidance (MSSG) technique is applied to derive the closed-loop guidance law,which stems from higher order sliding mode control theory and has advantage in the finite time reaching property.The global stability of the proposed guidance approach is proved by the Lyapunov-based method.The designed guidance law can generate new trajectories on-line without any specific requirement on off-line analysis except for the information on the boundary conditions of the A&L phase and instantaneous states of the RLV.Therefore,the designed guidance law is flexible enough to target different touchdown points on the runway and is capable of dealing with large initial condition errors resulted from the previous flight phase.Finally,simulation results show the effectiveness of the proposed guidance law in different scenarios. 相似文献