共查询到20条相似文献,搜索用时 875 毫秒
1.
2.
3.
为了充分利用复合材料加筋板的后屈曲承载能力,针对复合材料加筋板的后屈曲行为开展优化设计方法的研究具有重要意义。详细探讨了筋条尺寸及密度等参数对承受面内剪切载荷作用下的复合材料双向加筋板屈曲后屈曲的影响规律。建立了复合材料加筋板考虑后屈曲响应的结构分级优化方法:在一级优化中以结构几何尺寸为设计变量,使用响应面法(RSM)拟合出结构后屈曲响应的全局近似函数,结果显示,加筋缘条的宽度及加筋的密度对屈曲承载能力有重要影响;在二级优化中采用遗传算法(GA)对复合材料铺层顺序进行优化,经过两级优化后的复合材料加筋板相比于初始设计在质量减少了3%的同时,线性屈曲位移提高了8.86倍,线性屈曲模态由局部屈曲改善为整体屈曲,同时结构的后屈曲承载能力提高了8.7%。基于解决旅行商问题(TSP)的遗传算法被调整用于固定铺层厚度的复合材料铺层顺序优化问题,经优化,结构线性屈曲特征值提高了12.76%,表明了优化方法的可行性。 相似文献
4.
对三种尺寸的复合材料薄壁加筋板在剪切载荷作用下的稳定性及承载能力进行了试验研究,得到结构的屈曲形式以及屈曲失稳、破坏载荷。试验结果表明复合材料加筋板在屈曲失稳后仍有较大的承载能力;蒙皮厚度及筋条数目对板的屈曲及破坏载荷有较大影响。 相似文献
5.
6.
为扩充航空复合材料结构稳定性设计手段,基于Levy形式级数和有限差分法,提出了面内纯弯曲载荷作用下两边简支两边固支(SSCC)复合材料层合板临界屈曲载荷的数值解法。首先,应用有限差分法将挠度函数进行离散化处理;然后利用边界条件扩充方程组,最后将临界屈曲载荷的求解转化为广义特征值问题。通过数值算例分别在各向同性板和复合材料层合板上验证了本文方法,并与有限元方法(FEM)进行了比较。结果表明,本文方法具有很高的精度,为复合材料层合板的屈曲分析开辟了新的途径。 相似文献
7.
运用基于工艺的“laminate modeler”模块创建了复合材料铺层和加筋层合板的三维有限元模型.介绍了一种体单元与壳单元节点融合的方法.以不同的相对节点间距对加筋层合板模型进行了有限元网格划分,采用结构最大Von Mises应力作为标准进行了收敛性分析,得到了一个可适用于其他类似加筋板模型网格创建的合理相对节点间距值1/72.应力计算表明,集中载荷作用下复合材料加筋壁板的初始损伤发生于第八铺层材料主方向的2方向,损伤模式为基体拉伸开裂.发生初始损伤时加筋板结构的极限载荷为75 N.应力集中区较小,且主要分布于载荷作用点附近.集中载荷作用下加筋板的承载效率较低. 相似文献
8.
为了研究复合材料薄壁加筋板结构的后屈曲承载能力以及影响后屈曲的主要因素,应用Abaqus软件对三种构型下的薄壁加筋板进行了有限元分析,并与试验结果进行对比。结果表明,复合材料薄壁加筋板结构在轴向压缩载荷下具有较大的后屈曲承载能力,有限元分析与试验得出的试验件后屈曲载荷均为初始屈曲载荷的7倍左右,蒙皮的厚度及筋条间距对加筋板的后屈曲承载能力影响不大,加筋板的后屈曲承载能力主要取决于筋条的刚度。在飞机结构设计中,可以充分利用薄壁加筋板结构的后屈曲承载能力来提高结构使用效率。 相似文献
9.
航空复合材料加筋板由于具有良好的力学性能,广泛地应用于航空结构中。本工作研究了航空复合材料加筋板压缩屈曲及后屈曲力学性能,首先应用工程方法对复合材料加筋板进行压缩稳定性计算,得到加筋板的屈曲载荷和破坏载荷的预估值;其次,开展复合材料加筋板压缩稳定性实验,得到实验件的屈曲及破坏形式、实验件的载荷-应变及载荷-位移关系和实验件的屈曲载荷和破坏载荷。结果表明:采用工程方法得到的计算结果与实验结果较为吻合,屈曲载荷和破坏载荷的误差分别为6.12%和9.31%,合理应用工程方法可以为实验提供较好的指导;加筋板的破坏形式为壁板的分层、鼓包和撕裂、筋条的断裂以及筋条-壁板的脱粘;屈曲比为1.65的复合材料加筋板具有较强的后屈曲承载能力;工程中可充分应用加筋板的后屈曲承载能力提高结构的利用效率。 相似文献
10.
纤维增强复合材料强度准则适用性 总被引:1,自引:0,他引:1
针对常用的三种单向纤维增强复合材料及其正交铺设层合板,讨论了最大应力准则和蔡-胡准则的适用性,给出了适合于纵向拉压性能不同的复合材料的强度准则,这对复合材料结构的安全分析和优化设计具有一定的应用价值。 相似文献
11.
12.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
15.
16.
17.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
18.
FU Hong-jun MA Chong-qi KUANG Nai-hang LUAN Shi-lin 《中国航空学报》2007,20(2):124-128
This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered. 相似文献
19.
Xu Chenghai Meng Songhe Zhang Mingfu Zuo Hongbo Wang Guigen 《中国航空学报》2007,20(5):475-480
本文利用有限元法对冷心放肩微量提拉法(SAPMAC)生长大尺寸蓝宝石单晶过程中的热应力进行了模拟计算,应用临界缺陷理论解释了裂纹的萌生与扩展机理。研究表明,晶体内的热应力主要与晶体生长速率,环境温度和结晶取向有关;较大热应力多出现在结晶界面,放肩、收尾以及直径急剧变化等位置;最大热应力总是出现在籽晶与新生晶体的界面附近。裂纹将在临界缺陷位置产生,并在应力作用下沿a或m面扩展。计算结果与实验结果基本吻合,通过晶体生长系统和生长工艺的改进,对晶体的开裂问题得到了有效的抑制。 相似文献
20.
CHENG Wen-yuan CHANG Yan CUI De-gang XIE Xiang-hui 《中国航空学报》2007,20(1):55-59
To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm (PPGA) is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis (FEA) software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources. 相似文献