共查询到20条相似文献,搜索用时 46 毫秒
1.
建立了具有涡轮叶尖间隙计算功能的发动机实时模型并设计了主动间隙控制系统,以反映涡轮叶尖间隙控制对发动机动、静态性能的影响。提出以半无限平面瞬态热传导与多项式拟合相结合的方法,更准确计算发动机动态过程中变化的叶尖间隙;基于涡轮叶尖间隙的变化量和涡轮性能参数的关系实时修正当前涡轮性能参数,提高了常规发动机部件级模型的计算准确度,且涡轮叶尖间隙每减少0.25mm,涡轮效率提高1%,耗油率下降1%;在分析气冷式主动间隙控制系统的基础上,设计了一种可以控制叶尖间隙变化的机械式主动间隙控制系统,使动态过程中变化的叶尖间隙始终处于指令间隙。通过对发动机地面加速过渡过程和巡航减速过渡过程的仿真,验证了上述方案的有效性。 相似文献
2.
分析了主动间隙控制活门漏油、高压涡轮叶片榫头裂纹、高压涡轮叶片腐蚀和高压涡轮冷却部件堵塞等四个典型故障的解决方法,总结出高压涡轮主动间隙控制系统、高压涡轮叶片、高压涡轮导向器及高压涡轮罩环的设计改进措施,为我国设计出维修性好和性能高的大涵道比涡扇发动机的高压涡轮提供了参考。 相似文献
3.
4.
5.
涡轮叶片叶顶间隙变化减敏研究 总被引:2,自引:1,他引:1
采用数值方法联合标准k-ω两方程湍流模型求解雷诺平均Navier-Stokes方程组,研究了平顶和分别采用被动、主动以及复合间隙控制方法的凹槽顶、平顶喷气、凹槽顶喷气4种不同叶顶结构下涡轮性能对叶顶间隙变化的敏感性,分析了间隙变化对间隙流场结构及损失的影响,研究了涡轮性能随叶顶间隙变化的规律,并对采用不同间隙控制方法的叶顶结构所带来的效率收益对攻角变化敏感性进行了评估.结果表明:在不同间隙控制方法下叶顶泄漏涡强度随间隙的增加速度变缓,尤其在复合间隙控制方法下更为明显,从而使得在复合间隙控制方法下涡轮性能对间隙变化的敏感度最低;仅仅涡轮叶片前缘区域泄漏流动对攻角变化比较敏感,使得凹槽顶结构具有最佳的攻角变化适应性. 相似文献
6.
7.
巡航状态下涡轮径向间隙主动控制 总被引:1,自引:0,他引:1
发动机叶尖间隙变大,会导致压气机和涡轮的工作效率下降,发动机推力减少,耗油率增大。主动间隙控制技术是根据发动机工作状态,人为地控制机匣或转子的膨胀量,使转子和静子的热响应达到良好的匹配,以保证径向间隙最小。针对涡轮在巡航状态下采用冲击冷却,确定涡轮在冲击冷却下的优化设计数学模型,利用MPOP优化程序综合寻优,达到涡轮在巡航状态下优化设计主动控制的目的。 相似文献
8.
涡轮叶尖泄漏流主动控制数值模拟研究(英文) 总被引:1,自引:1,他引:0
在涡轮设计中一直追求减小损失、提高效率,流动控制作为一种减小损失的一种有效手段,在涡轮叶尖泄漏流动方面引起广泛的关注,因此本文对在涡轮叶尖表面进行主动射流对叶尖泄漏流动的影响作了数值模拟。结合基于密度修正的采用雷诺应力湍流模型加壁面函数的三维计算流体力学程序,详细分析不同叶尖间隙高度下射流孔位置和射流流量改变对间隙泄漏流场的影响,并相应地阐述射流主动控制的机理,分析了主动射流条件下叶尖间隙流动的拓扑结构,最后计算考虑射流影响的涡轮转子效率。结果表明:在涡轮叶尖表面选择合适射流孔位置进行射流可以提高涡轮转子效率,其中大间隙下通过射流孔组合射流可以提高涡轮效率0.35%,小间隙下可以提高0.30;在射流孔区域靠近叶片表面处流场结构中鞍点数和结点数相等,若不考虑周围流场的拓扑结构,则射流孔附近的流场满足奇点分布规律。 相似文献
9.
为控制涡轮叶栅中叶顶间隙泄漏流动和改善涡轮气动性能,将扫频式射流器(SJA)作为一种主动流动控制方法应用在涡轮叶栅的研究中。通过非定常数值计算,分析了SJA对涡轮叶栅叶顶间隙流动的作用过程以及作用机理,并且研究了不同工况下SJA对涡轮叶顶流场改善效果以及不同频率的SJA对叶顶流场的影响。结果表明:通过在涡轮叶栅上端壁增加单个SJA装置,可以有效地延迟上端壁的流动分离,其中最佳方案射流流量仅为进口总流量的0.35%,涡轮叶栅出口截面总压损失系数减少了11.48%。存在着最佳的频率284Hz,使SJA装置对流场的作用效果最佳,有效地改善了涡轮叶栅内的间隙流动。 相似文献
10.
针对有主动间隙控制的某型高压涡轮,建立了考虑发动机退化的叶尖间隙预估模型,重点研究了发动机在长期使用、性能退化过程中涡轮前燃气温度和蠕变变形对叶尖间隙的影响。研究中,首先分析了间隙预测中发动机性能退化影响的引入方式,建立了对应的间隙预估流程。随后以某型发动机典型工作历程为对象,对比研究了传统间隙控制方案、考虑发动机性能退化影响两种条件下的涡轮叶尖间隙尺度变化规律,并据此开展了间隙控制策略的优化调整。研究中发现,由于发动机性能的退化,导致涡轮前燃气温度升高,使得机匣、轮盘和叶片的热变形量增大,其中在最大巡航阶段对机匣的影响最大,其伸长量达到了6.914mm,与未退化前相比增大了17%,同时由于发动机的长期使用,叶片和轮盘受蠕变变形影响,导致叶尖间隙的变化。研究结果表明,采用优化后的主动间隙控制方案,各个工况下的叶尖间隙值均控制在合理范围内,尤其在高温起飞阶段,与退化状态下的间隙值相比提高了53%,有效避免了叶片严重碰摩等故障发生。 相似文献
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献