飞机结构紧固孔超差修理的补偿措施

在飞机生产和飞机大修过程中,经常遇到飞机上连接孔的超差问题需要处理.这些:孔主要指飞机机体结构重要接头机械连接紧固孔,如机翼、机身连接接头孔,垂直安定面与机身连接接头孔,舵面与安定面连接接头孔,起落架转轴接头孔,操纵摇臂连接拉杆孔等.     

湿热环境对复合材料螺栓连接强度的影响

正复合材料机械连接由于其成本低、不易破坏、维修方便等优点,而被广泛地用于航空工业中,在飞机结构中占有重要的地位。近年来对于复合材料机械连接的研究比较多,但鲜见有关环境对复合材料机械连接强度的影响分析报道。由于飞机在飞行时所处的气流环境复杂,复合材料机械连接接头往往会处在不同温湿环境下工作,因此对于温湿度对复合材料机械连接接头强度的影响研究是十分必要的。     

SiC颗粒增强Al基复合材料焊接工艺研究

通过SiC颗粒增强Al基复合材料与Al合金的焊接工艺试验研究，重点分析了材料组合，保湿工艺，连接时间等工艺参数对连接接头性能的影响以及连接接头的微观组织及成分分布，研究表明，TLP扩散连接是一种适用于复合材料连接的重要方法，在相同工艺条件下，LF6／SiCp-6061Al的接头性能明显优于LF6／SiCp-2024Al，连接时间过短或过长，都将影响到接头性能，并且连接时间对不同材料组合的影响也不同，采用二次保温工艺可以较大幅度地提高接头性能。     

自冲铆连接工艺数值模拟及优化研究进展

自冲铆接技术作为新型连接技术,在薄板材料的连接中具有优异的连接性能。其接头质量受连接的可行性和连接参数的影响,而接头质量主要由接头的力学性能来表征,因此接头的质量和力学性能已成为目前自冲铆技术的主要研究方向。随着数值模拟技术的发展,它在自冲铆连接技术上的应用成为一种研究趋势。对近年来自冲铆数值模拟技术的发展进行系统阐述,从自冲铆接头成形质量的数值模拟技术出发,对自冲铆数值模型建立、自冲铆影响因素研究、数值模型优化和数值预测模型4个方面进行说明,综述了材料连接的可行性和连接参数对接头性能的影响,对接头力学性能进行模拟,并对接头力学强度和疲劳寿命进行预测,为自冲铆工艺的研究和发展提供新的方向。     

机身侧挂点接头结构设计方案分析

介绍了3种机身侧挂架接头的结构设计方案，即盒梁形式、交点框形式以及盒梁和框综合形式。论述了侧挂架接头的6种连接形式，通过分析对比，认为交点框传力形式和机身内锥体斜挂式挂架接头连接方案为最佳设计方案。     

降低陶瓷与陶瓷或金属连接温度的技术

为降低陶瓷与陶瓷或金属的连接温度，目前采用的连接方法有过渡液相扩散连接、兰固态连接、机械连接、粘接、铟封和陶瓷表面低温改性后低温钎焊等。本文从上述连接方法的原理设计、连接材料设计与制备、接头性能及各自的优缺点等方面综述了陶瓷与陶瓷或金属低温连接研究的现状。     

SiCp/101铝基复合材料铜中间层TLP扩散焊工艺研究

通过颗粒增强铝基复合材料的铜中间层TLP扩散连接试验,对接头性能的影响因素进行了研究,并采用扫描电镜和电子探针等手段分析了接头连接机理、微观组织与接头性能的关系,从而确定了其试验条件和焊接规范.     

先驱体浓度、工艺温度及惰性填料对先驱体高温连接陶瓷材料性能的影响

对先驱体硅树脂高温(800～1400℃)转化陶瓷接头连接石墨、SiC陶瓷及Cf/SiC复合材料进行了研究,着重对硅树脂固化裂解过程、硅树脂溶液浓度、裂解温度及惰性填料对连接性能的影响进行了探讨.研究表明,硅树脂的交联固化主要是通过消耗Si-OH来完成,先驱体溶液的浓度及裂解温度根据基材的不同而有不同影响,适当加入惰性填料SiC可以提高硅树脂对Cf/SiC复合材料的连接性能.     

钛合金高温钎焊接头的组织性能及影响因素评价

综述了钛及钛合金高温钎焊结构在现代工业中的应用。在分析了钛基钎料应用和发展的基础上，重点分析了钎焊接头的组织与接头性能的关系以及影响因素。指明接头组织中脆性金属间化合物相的存在形态是决定接头性能的主要因素，接头间隙和钎焊时间决定了接头的组织形态，从而影响接头的性能。钛及钛合金高温钎焊接头的拉伸性能、高温性能和疲劳性能是优越的，而接头氧化后的性能急剧下降。并展望了钛基材料连接的发展方向。     

垂直度误差对复合材料单钉连接性能的影响

为揭示连接孔垂直度误差对航空复合材料连接性能的影响规律,对准各向同性碳纤维环氧树脂复合材料板进行了单钉单剪试验研究。以极限承载强度、弦刚度、2%偏移承载强度为指标研究连接孔的倾斜角度、倾斜方向以及螺栓扭矩对接头承载性能的影响规律。试验结果表明:当连接孔倾斜角度从0°增加到4°时,接头弦刚度增大10%~40%,极限承载强度下降9%~12%;连接孔倾斜方向对极限承载强度影响甚微,却可使接头弦刚度产生20%~30%的变化;增加螺栓扭矩可以有效提高极限承载强度,但对接头刚度无明显影响;连接孔倾斜角度越大,则螺栓扭矩的增大对2%偏移承载强度的强化效果越不明显。     

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

航空发动机管路测量数据分割方法

 为了提高航空发动机管路测量数据的反求建模效率,提出了一种区域增长分割算法。该方法主要是利用管路表面在曲面索引系数映射、主曲率映射、高斯映射上的特性,并基于均值漂移算法和遗传算法提出了区域分割算法中种子区域的选择策略。然后利用区域增长分割方法实现了对管路测量数据的分割。经过仿真和实测数据验证,所提管路分割算法具有较好的分割质量和效率。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

Interfacial Properties Modification of Carbon Fiber/ Polyarylacetylene Composites

This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered.     

Thermal Stresses and Cracks During the Growth of Large-sized Sapphire with SAPMAC Method

本文利用有限元法对冷心放肩微量提拉法(SAPMAC)生长大尺寸蓝宝石单晶过程中的热应力进行了模拟计算,应用临界缺陷理论解释了裂纹的萌生与扩展机理。研究表明,晶体内的热应力主要与晶体生长速率,环境温度和结晶取向有关;较大热应力多出现在结晶界面,放肩、收尾以及直径急剧变化等位置;最大热应力总是出现在籽晶与新生晶体的界面附近。裂纹将在临界缺陷位置产生,并在应力作用下沿a或m面扩展。计算结果与实验结果基本吻合,通过晶体生长系统和生长工艺的改进,对晶体的开裂问题得到了有效的抑制。     

Optimization Design System for Composite Structures Based on Grid Technology

To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis （FEA） software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources.