共查询到20条相似文献,搜索用时 27 毫秒
1.
总结、分析了国内外大、小功率电机在外场使用与厂内试验中产生的大量故障时间数据 ,并分别选取典型产品进行详细的数据分析与拟合 ,结合文献分析 ,得出电机的故障时间分布模型。 相似文献
2.
固体发动机由众多部件组成,并且各部件的可靠性分布均不相同,若要全面评定发动机结构可靠性,则需要较大的子样数。因此,采用全尺寸、全系统试验来全面评定发动机可靠性的方法是行不通的。为了解决此问题,提出利用发动机的基础组件的可靠性数据,建立发动机系统的金字塔模型,再通过数据等效折算,将各组件不同分布的可靠性试验数据折算成成败型数据,采用L-M法综合评定了某型固体发动机可靠性。 相似文献
3.
A systematic reliability analysis procedure for evaluating fault-tolerant inertial measurement unit (IMU) architectures is described. The procedure is based on modeling the system architecture, the component reliabilities, and the redundancy management. The component reliabilities are based on constant failure rates and exponential failure distributions. The overall reliability of the IMU and the major contributors to IMU reliability are computed. Three state-of-the-art fault-tolerant IMU architectures are evaluated and compared using the procedure 相似文献
4.
本文综合考虑了飞机构件疲劳与断裂两方面的特性,提出了在计及裂纹漏检条件下计算成对使用的机翼主要构件在任一检查周期内破断全概率的一种可靠性分析方法。并且,以某型后掠式飞机机翼主梁为例,给出了计算结果。 相似文献
5.
Dynamic fault tree analysis is widely used for the reliability analysis of the complex system with dynamic failure characteristics. In many circumstances, the exact value of system reliability is difficult to obtain due to absent or insufficient data for failure probabilities or failure rates of components. The traditional fuzzy operation arithmetic based on extension principle or interval theory may lead to fuzzy accumulations. Moreover, the existing fuzzy dynamic fault tree analysis methods are restricted to the case that all system components follow exponential time-to-failure distributions. To overcome these problems, a new fuzzy dynamic fault tree analysis approach based on the weakest n-dimensional t-norm arithmetic and developed sequential binary decision diagrams method is proposed to evaluate system fuzzy reliability. Compared with the existing approach, the proposed method can effectively reduce fuzzy cumulative and be applicable to any time-to-failure distribution type for system components. Finally, a case study is presented to illustrate the application and advantages of the proposed approach. 相似文献
6.
工程实际中,维修活动开展前往往存在一定时长的准备期,且由于环境时变性、系统长期运行后的劣化累积等因素导致部件状态性能水平存在不确定性,使得系统可靠性建模较为困难。对此,运用模糊数表征系统部件的失效转移率、修复转移率及修理工维修准备率的同时,以Power Law规则刻画部件间的故障相关关系,认为部件承担载荷超过某阈值时才会引发故障相关现象,并考虑了修理工数量与故障件数量之间关系对系统可靠性的影响,研究了载荷动态分配条件下带维修准备期的多修理工n中取k模糊多状态系统模型,建立了状态转移微分方程组,提出用逆向逐层分析的思路建立系统稳态概率系数的递推关系,应用α水平截集及Zadeh扩张原理确定了模糊状态概率的截集区间,得到了系统模糊稳态指标,最后通过算例给出了修理工数量及部件参数模糊程度对系统稳态指标的影响,验证了模型的适用性。 相似文献
7.
To comprehensively consider the effects of strength degeneration and failure correlation, an improved stress-strength interference (SSI) model is proposed to analyze the reliability of aeroengine blades with the fatigue failure mode. Two types of TC4 alloy experiments are conducted for the study on the damage accumulation law. All the parameters in the nonlinear damage model are obtained by the tension-compression fatigue tests, and the accuracy of the nonlinear damage model is verified by the damage tests. The strength degeneration model is put forward on the basis of the Chaboche nonlinear damage theory and the Griffith fracture criterion, and determined by measuring the fatigue toughness during the tests. From the comparison of two kinds of degeneration models based on the Miner’s linear law and the nonlinear damage model respectively, the nonlinear model has a significant advantage on prediction accuracy especially in the later period of life. A time-dependent SSI reliability model is established. By computing the stress distribution using the finite element (FE) technique, the reliability of a single blade during the whole service life is obtained. Considering the failure correlation of components, a modified reliability model of aero-engine blades with common cause failure (CCF) is presented. It shows a closer and more reasonable process with the actual working condition. The improved reliability model is illustrated to be applied to aero-engine blades well, and the approach purposed in this paper is suitable for any actual machinery component of aero-engine rotor systems. 相似文献
8.
针对液体火箭发动机可靠性评估过程中试验数据利用不充分、主观性强、与设计改进关联不足等现状,给出了一种可靠性双线评估方法,在有限试车条件下提升可靠性评估结果的准确性,并从风险控制角度识别出发动机的薄弱环节。该方法采用两条主线开展可靠性评估,第一条线以发动机部组件试验数据为输入,以发动机工作时序为线索,识别发动机故障模式,建立可靠性模型,将部组件故障模式的发生概率带入可靠性模型中,采用不确定性传播算法,得到发动机可靠性先验分布。第二条线以发动机整机试验数据为输入,采用威布尔可靠性评估方法,得到发动机可靠性追加信息;随后采用贝叶斯方法进行双线融合,计算发动机可靠性的后验分布。通过可靠性双线评估方法,扩充了可靠性评估的数据来源,并从风险控制角度辨识了发动机的关键部组件及其故障模式,提升了可靠性评估的工程应用价值。 相似文献
9.
10.
构件振动可靠性设计方法初探 总被引:9,自引:4,他引:5
本文提出一种进行构件振动可靠性设计的方法,建立了激振力频率与构件固有频率干涉的概率模型,并利用Goodman曲线,给出了将导致构件损坏的强迫共振响应的概率计算公式及其使用条件。原则上,本文方法对其固有频率相对不太密集的构件更为适用,如航空发动机中的叶片。 相似文献
11.
针对飞机维修工作中发动机引气系统故障率较高问题,以寿命数据分析为基础,运用威布尔分布模型定量评估航空发动机部件可靠性,建立了民用航空发动机引气系统部件可靠性寿命模型。以V2500发动机引气系统为例,收集了该系统的可靠性数据,分析了部件的非计划拆换情况。在数据计算过程中采用3参数威布尔分布模型对引气系统部件的寿命数据进行拟合。假设检验结果表明,在对部件进行寿命可靠性分析时,运用威布尔分布建立的数学模型符合客观规律,且能够取得良好的拟合效果。依据计算出的部件可靠性特征量对部件的可靠性状况进行定量评估,结果表明:在评估复杂机械电子系统的可靠性时,威布尔分布模型具有较大应用价值。 相似文献
12.
13.
本文在综合考虑裂纹检出概率、检查间隔、初始裂纹尺寸分布,裂纹扩展、剩余强度分布等因素的条件下,提出了基于概率断裂力学原理的主副梁式机翼结构的破坏危险性分析方法。并以某型飞机机翼为例,进行了数值计算。结果表明:副梁疲劳寿命对主梁的破坏危险性有显著影响。 相似文献
14.
针对随机失效阈值下的退化可靠性分析问题,利用可能性分布表征失效阈值中的不确定性,提出了一种退化失效建模的可靠性分析方法,解决了预测模型中不确定性的传递问题。通过陀螺仪剩余寿命预测的案例研究,阐明了文中方法的有效性。 相似文献
15.
改进Delta并联机构运动可靠性分析 总被引:2,自引:0,他引:2
运动精度是评价机构质量的重要考核指标。以往并联机构运动精度分析中,往往不考虑输入误差的随机性,造成评价结果不准确。首先应用齐次坐标变换,推导了改进Delta并联机构的位置反解公式。基于位置反解和一阶泰勒展开,建立了包含机构尺寸误差、转动副间隙误差和驱动误差的机构位置误差计算模型。利用该误差模型,考虑各个原始输入误差的随机性,推导了机构运动可靠性数学模型,给出了评价机构运动可靠性高低的量度和计算方法。运动可靠性是机构运动精度高低的更本质的衡量指标。运动可靠性分析是机构优化设计和误差补偿的基础。 相似文献
16.
用摄动法研究几何尺寸为随机量时轮盘的可靠性 总被引:1,自引:0,他引:1
几何尺寸和材料性质等的随机性都影响结构的可靠性。本文提出用建立在二阶摄动法基础上的概率有限元来分析轮盘的几何形状不确定时的随机应力场和可靠性, 研究用摄动方法处理问题的基本思路, 推导随机应力场和可靠度的计算公式, 用简单算例分析讨论了几何尺寸对可靠性的影响规律, 算例结果与MonteCarlo模拟结果的对比表明本文的方法有效, 理论正确。 相似文献
17.
发动机构件低循环疲劳模拟试验件设计方法 总被引:3,自引:0,他引:3
通过多子样模拟件可靠性寿命试验,补充构件试验量的不足,得到构件可靠性寿命,是解决发动机构件试验费昂贵的有效途径。探讨了低循环疲劳模拟试验件的设计方法,讨论了相关的寿命模型、设计准则和模拟件典型样式。 相似文献
18.
19.