一种不借助零磁线圈的星载磁强计校准方法

文章介绍一种星载磁强计校准装置及方法。首先,将高精度地面磁强计的三分量磁传感器置于标准磁场发生装置形成的磁场环境内,通过后端数据处理装置采集得到第一磁场数据,并进行不同量程下螺线管线圈常数C_i的标定;然后,将星载磁强计置于上述标准磁场环境内,并以高精度地面磁强计不同量程下获得的C_i作为基准,通过后端数据处理装置采集得到第二磁场数据;最后,对第一磁场数据和第二磁场数据进行比对,得到星载磁强计的量程、分辨率及稳定性校准值。上述校准项目所有参数的校准结果不确定度为u=0.12%（k=2）。本方法已成功应用于多种军民型号星载磁强计校准。     

用于微小卫星自主导航控制系统地面仿真的磁强计数学模型

对基于磁强计自主导航微小卫星控制系统地面仿真的磁强计数学模型建立进行了研究。给出了地磁场理论数据的生成模型及磁强计的测量模型,并据此建立了磁强计测量数据生成的数学模型。对低轨圆轨道微小卫星的仿真计算结果表明：由该磁强计数学模型获得的磁场强度测量值与文献中真实磁强计测量数据差异很小,验证了模型的有效性和准确性。     

A global geographical survey of received signal strength in the VHF band

Sumbandila (SO-67) is an 81 kg LEO satellite launched on 17 September 2009. Its primary payload is a multi-spectral imager with a ground sampling distance of 6.25 m at an orbit altitude of 500 km. Its two command transceivers operate in the commercial and amateur radio VHF and UHF bands and one of them provides a VHF to UHF repeater service to radio amateurs. This paper presents initial results of a global three week monitoring period of two VHF frequency ranges. The data is obtained by executing on-board flight control procedures to select the frequencies to measure. The existing on-board telemetry gathering system is employed to record the data, most notably the received signal strength for the selected frequency. The data is downloaded using an adaptation of the imagery data download path. We determine regions of high signal levels by distributing individual measurements over cells in the satellite footprint before averaging over the cells. The data is then plotted on a geographical signal strength heatmap. We compare our results with that of a similar study of the late 1990s and point out changes since then. The data provides useful information for selecting future ground station locations for minimum interference. It further gives an indication of frequencies to use for command and telemetry communication at existing ground stations. We propose that including a receiver capable of measuring frequency interference across a desired frequency range is very useful to future missions for selecting communication frequencies from this range for ground station locations.     

Attitude control schemes for the first recovery mission of India

This paper describes the attitude control schemes for the various phases such as acquisition, on-orbit, orbit maneuver, de-boost maneuvers and coast phases of the India's first recovery mission Space Capsule Recovery Experiment-I (SRE-1). During the on-orbit phase, the SRE was configured to point the negative roll axis to Sun. The attitude referencing of SRE-1 was based on dry tuned gyros with updates from the attitude determined using on-board Sun sensors and magnetometer. For attitude acquisition, attitude maneuvers and for providing the velocity corrections for de-orbiting operations; a set of eight thrusters grouped in functionally redundant blocks were used. The control scheme with thrusters was based on proportional derivative controller with a modulator. In order to ensure micro-gravity environment during the on-orbit payload operations a linear quadratic regulator (LQR) based control scheme was designed to drive an orthogonal configuration of magnetic torquers which in turn produced three-axis control torque with the interaction of Earth's magnetic field. Proportional derivative control scheme with modulator was designed to track the steering commands during the velocity reduction as well as during the coasting phase of the de-orbiting operations. A novel thruster failure detection, isolation and reconfiguration scheme implemented on-board for the de-orbiting phase is also discussed in this paper.     

基于DSP28335的质子旋进式磁力仪控制系统设计与实现

质子旋进式磁力仪是依据质子的旋进频率来测量地磁场的仪器。文章在分析了国内外质子磁力仪发展现状的基础上,提出了以DSP28335为核心的新型质子旋进式磁力仪控制系统的设计方案,着重介绍了数字控制板的设计和测频关键技术。与以单片机、PIC为控制芯片的传统磁力仪不同,新设计旨在解决现有系统成本高、功能有限和硬件电路复杂等问题,并完成了原理样机的研制。最后在实验室内对关键的测频技术进行了针对性测试,测量精度达到国内先进水平。     

Determination of the Microacceleration Quasisteady Component onboard the International Space Station

A comparison of two methods of determination of the microacceleration quasisteady component arising onboard the International Space Station was performed. In the first method the acceleration was calculated using the relative motion of the station reconstructed on the basis of telemetry data. The second method was a direct measurement of the microacceleration by a low-frequency accelerometer and a smoothing of the data obtained. The used measurements were made by the American accelerometer MAMS. The above comparison can theoretically be used to refine the position of the station center of mass relative to its body.     

Optimization of space orbits design for Earth orbiting missions

In Earth orbiting space missions, the orbit selection dictates the mission parameters like the ground resolution, the area coverage, and the frequency of coverage parameters. To achieve desired mission parameters, usually Earth regions of interest are identified and the spacecraft is maneuvered continuously to visit only these regions. This method is expensive, it requires a propulsion system onboard the spacecraft, working throughout the mission lifetime. It also requires a longer time to cover all the regions of interest, due to the very weak thrust forces compared to that of the Earth's gravitational field. This paper presents a methodology to design natural orbits, in which the regions of interest are visited without the use of propulsion systems, depending only on the gravitational forces. The problem is formulated as an optimization problem. A genetic algorithm along with a second order gradient method is implemented for optimization. The design process takes into consideration the gravitational second zonal harmonic, and hence allows for the design of repeated Sun-synchronous orbits. The field of view of the payload is also taken into consideration in the optimization process. Numerical results are presented that demonstrates the efficiency of the proposed method.     

Estimating the accuracy of the technique of reconstructing the rotational motion of a satellite based on the measurements of its angular velocity and the magnetic field of the Earth

The paper has studied the accuracy of the technique that allows the rotational motion of the Earth artificial satellites (AES) to be reconstructed based on the data of onboard measurements of angular velocity vectors and the strength of the Earth magnetic field (EMF). The technique is based on kinematic equations of the rotational motion of a rigid body. Both types of measurement data collected over some time interval have been processed jointly. The angular velocity measurements have been approximated using convenient formulas, which are substituted into the kinematic differential equations for the quaternion that specifies the transition from the body-fixed coordinate system of a satellite to the inertial coordinate system. Thus obtained equations represent a kinematic model of the rotational motion of a satellite. The solution of these equations, which approximate real motion, has been found by the least-square method from the condition of best fitting between the data of measurements of the EMF strength vector and its calculated values. The accuracy of the technique has been estimated by processing the data obtained from the board of the service module of the International Space Station (ISS). The reconstruction of station motion using the aforementioned technique has been compared with the telemetry data on the actual motion of the station. The technique has allowed us to reconstruct the station motion in the orbital orientation mode with a maximum error less than 0.6° and the turns with a maximal error of less than 1.2°.     

空间站有效载荷真空支持系统方案评述

有效载荷真空支持系统是空间有效载荷支持系统的重要组成部分,为空间有效载荷实验的顺利进行提供真空环境支持和保证。文章详细分析了国际空间站包括美国“命运号”实验舱（USL）、欧空局哥伦布轨道舱（APM）及日本实验舱（JEM）内的有效载荷真空支持系统方案及使用情况;对美国实验舱内的一号微重力材料科学机柜及微重力燃烧科学机柜内部专用的真空支持系统作了主要介绍;最后提出了我国空间站有效载荷真空支持系统的初步方案设想,即合理安排有效载荷实验进行次序,将废气排放子系统及真空资源子系统合二为一,以节约资源,提高可靠性。     

Relationship between the fluxes of relativistic electrons at geosynchronous orbit and the level of ULF activity on the Earth’s surface and in the solar wind during the 23rd solar activity cycle

We present the results of a cross-correlation analysis made on the basis of Spearman’s rank correlation method. The quantities to correlate are daily values of the fluence of energetic electrons at a geosynchronous orbit, intensities of ground and interplanetary ultra-low-frequency (ULF) oscillations in the Pc5 range, and parameters of the solar wind. The period under analysis is the 23rd cycle of solar activity, 1996–2006. Daily (from 6 h to 18 h of LT) magnetic data at two diametrically opposite observatories of the Intermagnet network are taken as ground-based measurements. The fluxes of electrons with energies higher than 2 MeV were measured by the geosynchronous GOES satellites. The data of magnetometers and plasma instruments installed on ACE and WIND spacecraft were used for analysis of the solar wind parameters and of the oscillations of the interplanetary magnetic field (IMF). Some results elucidating the role played by interplanetary ULF waves in the processes of generation of magneospheric oscillations and acceleration of energetic electrons are obtained. Among them are (i) high and stable correlation of ground ULF oscillations with waves in the solar wind; (ii) closer link of mean daily amplitudes of both interplanetary and ground oscillations with ‘tomorrow’ values of the solar wind velocity than with current values; and (iii) correlation of the intensity of ULF waves in the solar wind, normalized to the IMF magnitude, with fluxes of relativistic electrons in the magnetosphere.     

Studies of the substorm on March 12, 1991: 1. Structure of substorm activity and auroral ions

The substorm on March 12, 1991 is studied using the data of ground-based network of magnetometers, all-sky cameras and TV recordings of aurora, and measurements of particle fluxes and magnetic field onboard a satellite in the equatorial plane. The structure of substorm activity and the dynamics of auroral ions of the central plasma sheet (CPS) and energetic quasi-trapped ions related to the substorm are considered in the first part. It is shown that several sharp changes in the fluxes and pitch-angle distribution of the ions which form the substorm ion injection precede a dipolarization of the magnetic field and increases of energetic electrons, and coincide with the activation of aurora registered 20° eastward from the satellite. A conclusion is drawn about different mechanisms of the substorm acceleration (injection) of electrons and ions.     

Measuring the economic benefits of an environmental monitoring satellite project: The value of information approach

This paper reports a first application of contingent valuation method to measure the value of information generated by earth science data from an environmental geostationary satellite payload called Geostationary Environmental Monitoring Satellite. The purpose of the space project is to improve the accuracy of air pollution information by enhancing air pollution monitoring and forecasting system coupled with conventional ground level monitoring stations located throughout South Korea.     

高速飞行器非视距短波通信的可行性验证飞行试验

当高速飞行器处于失稳失控等紧急情况时，现有航天器测控方法可能面临地面站天线无法及时跟踪和对准飞行器的问题，这将导致测控通信链路的中断，无法传输紧急的安控遥控指令。为了在飞行器失稳失控、非视距通信时与地面站维持通信，提出将短波通信应用于高速飞行器测控通信系统的应急通信，并进行非视距短波通信的飞行试验以验证方法的可行性。在试验中，地面站发射7 MHz的短波信号，高速飞行器内部安装的交流磁场计用于接收短波信号，获得了短波的磁场强度与飞行环境的本底噪声。试验结果表明，随着飞行器海拔的增加，磁场强度减小，高速飞行器始终能在非视距和天线不对准的情况下接收到短波信号，证实了短波应用于高速飞行器应急通信的可行性。试验是进一步验证高速飞行器在远距离、超视距以及拒止环境下应急通信的技术基础，同时，也为高速飞行器短波通信系统的研制提供重要的数据支撑。     

Using the PROGRESS transport spacecraft in structure of the International Space Station for realization of scientific experiments under microgravity conditions

The problem is considered of using the PROGRESS transport spacecraft, which will deliver the payload on the ISS, as a free flying platform for realization of space experiments. For maintenance of the ISS 5-6 PROGRESS flights per year are planned. Usually after delivery of the payload the PROGRESS undocks from the ISS and burns down in the Earth atmosphere. However, the operating conditions of its onboard systems allow to prolong operation and to make free flight near to the station and repeatedly to be docked to it. It is offered to use this possibility for performing experiments on Material Science.     

常规兵器远程箭弹遥测的数据传输与处理

论述了在常规兵器远程箭弹遥测系统中进行多站接力串行无线数据传输、建立ＧＰＳ遥测时统以及遥测数据处理等问题     

Io Volcano Observer (IVO): Budget travel to the outer Solar System

The IVO mission would make multiple close encounters with Io while orbiting Jupiter in an inclined elliptical orbit. The payload includes narrow-angle and wide-angle cameras (NAC and WAC), dual fluxgate magnetometers (FGM), a thermal mapper (ThM), dual ion and neutral mass spectrometers (INMS), and dual plasma ion analyzers (PIA). The mission is designed to answer key outstanding questions about Io, especially the nature of the intense active volcanism and internal processes that drive the volcanism. IVO can collect and return 20 Gb of compressed science data per Io encounter, 100 times the total Io data return from the 8yr Galileo tour.     

基于地磁场测量估计卫星姿态的UKF算法

提出了利用UKF（Unscented Kalman Filter）处理地磁场测量数据进行低轨道（LEO）卫星自主定姿的算法。通过使用估计姿态、轨道参数和国际地磁场参考（IGRF）计算得到的地磁矢量与三轴磁强计（TAM）的测量矢量之差作为更新信息，可以实现实时的姿态角和角速度估计。针对卫星稳态定姿、大角度快速机动的定姿以及姿态失控状态下的定姿等三种任务，分别用UKF和传统的EKF（Extended Kalman Filter）进行了数值仿真。仿真结果显示出本文提出的定姿算法的优越性。     

Plastic Cubesat: An innovative and low-cost way to perform applied space research and hands-on education

This paper describes the design and the manufacturing of a Cubesat platform based on a plastic structure.The Cubesat structure has been realized in plastic material (ABS) using a “rapid prototyping” technique. The “rapid prototyping” technique has several advantages including fast implementation, accuracy in manufacturing small parts and low cost. Moreover, concerning the construction of a small satellite, this technique is very useful thanks to the accuracy achievable in details, which are sometimes difficult and expensive to realize with the use of tools machine. The structure must be able to withstand the launch loads. For this reason, several simulations using an FEM simulation and an intensive vibration test campaign have been performed in the system development and test phase. To demonstrate that this structure is suitable for hosting a complete satellite system, offering innovative integrated solutions, other subsystems have been developed and assembled.Despite its small size, this single unit (1U) Cubesat has a system for active attitude control, a redundant telecommunication system, a payload camera and a photovoltaic system based on high efficiency solar cells.The developed communication subsystem has small dimensions, low power consumption and low cost. An example of the innovations introduced is the antenna system, which has been manufactured inside the ABS structure. The communication protocol which has been implemented, the AX.25 protocol, is mainly used by radio amateurs. The communication system has the capability to transmit both telemetry and data from the payload, in this case a microcamera.The attitude control subsystem is based on an active magnetic system with magnetorquers for detumbling and momentum dumping and three reaction wheels for fine control. It has a total dimension of about 50×50×50 mm. A microcontroller implements the detumbling control law autonomously taking data from integrated magnetometers and executes pointing maneuvers on the basis of commands received in real time from ground.The subsystems developed for this Cubesat have also been designed to be scaled up for larger satellites such as 2U or 3U Cubesats. The additional volume can be used for more complex payloads. Thus the satellite can be used as a low cost platform for companies, institutions or universities to test components in space.     

Mathematical Modeling of Convection in the DACON Sensor under Conditions of Real Space Flight

A mathematical model of the operation of the sensor of convection under ground and space conditions is described, and the results of modeling are compared to experimental data. A good agreement of the model and experiment is obtained for ground conditions. The sensor operation under conditions of a space flight is simulated using actual microaccelerations that took place onboard the Mirstation. Good sensitivity of the sensor to the measured components of acceleration is demonstrated. The results of simulation are compared to the results of space experiments carried out with the DACON instrument onboard the Mirstation.