共查询到20条相似文献,搜索用时 46 毫秒
1.
2.
结合深空探测项目研制任务研究遥控数据接收处理电路FPGA片上容错设计技术。在研究航天器遥控数据接收处理电路数据模型的基础上,提出遥控数据接收处理电路FPGA片上小粒度自主备份容错设计方法;应用此新方法进行遥控指令通道FPGA设计优化;针对FPGA缺陷成团性,进行遥控指令通道FPGA布局优化,最终设计出能够自主容错,容错能力更强,可以应对缺陷成团性影响的新一代遥控指令通道FPGA。这一FPGA的实现,验证了文中提出的新方法,也为未来深空探测项目、微小卫星等提供新的遥控产品。 相似文献
3.
本文论述 STD 总线双机容错系统的设计与实现,该系统为工矿企业提供高可靠性的处理机模块。本系统采用双机容错原理,模块内部包含两个CPU 协同工作,还可用同样的处理机模块作为热备份,当运行模块失效后系统能自动切换到备份模块运行,实现系统的不间断运行。文中最后讨论了系统的软硬件结构及主要实验结果。 相似文献
4.
卫星控制系统用的数字计算机是实时性能很强的控制机,又是信息量较大的数据处理机,同时要求可靠性极高。一般,星载计算机设计成一台双机热备份的容错计算机系统。文章介绍了星载计算机的元器件选择,主机构成及其性能,各种系统软件和应用软件的设计准则,以及整机测试方法等。着重介绍了星载计算机硬件和软件的容错设计。文章最后介绍了星载计算机的使用情况,星载计算机成功地完成了二次飞行试验任务,表明设计思想正确,满足总体技术要求,控制精度高。采用双机热备份系统确实保证了计算机的高可靠性要求。 相似文献
5.
基于双CAN总线的透明式网关设计 总被引:1,自引:0,他引:1
基于双CAN总线的透明网关实现了控制系统中关键控制单元与双CAN总线之间的互连,网关中采取的容错设计以及关键信息的热备份处理提高了信息交互的可靠性,网关通信协议设计使网关具有较强的兼容性以及使用的灵活性,网关还为控制系统中各功能单元按模块化设计提供了技术保障,具有很强的实用推广价值。 相似文献
6.
微小卫星星务计算机系统的容错控制策略研究 总被引:7,自引:0,他引:7
微小卫星系统是一个可靠性要求很高的系统,需要由具有容错能力的星载计算机来控制。针对微小卫星重量、体积、功耗的限制,提出了一种微小卫星的星务计算机系统的可靠性设计方案,设计中采用双模冗余方案搭建系统的容错结构,并根据卫星的运行要求提出了适用于微小卫星的温备份方式容错控制策略,介绍了一些用于支持温备份方式容错控制策略的关键技术。通过分析在微小卫星设计中的适用情况,温备份策略从硬件开销和时间开销两个方面都有利于卫星的设计。在立体测绘微小卫星“试验卫星一号”的星务计算机系统中的应用表明,提出的可靠性设计方案能够提高小卫星的可靠性、安全性以及实时性。 相似文献
7.
8.
9.
10.
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
13.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
14.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
15.
16.
金属网由于柔韧性好、使用方便等优势而在电缆屏蔽工程上得到广泛应用。本文对电缆用的金属网屏蔽效能进行工程计算,通过计算,对金属网不同材料、不同规格、单层与双层屏蔽及有缝隙情况下的屏蔽效能进行比较与分析,对工程应用有一定的指导意义。 相似文献
17.
18.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
19.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献