BDS-2/BDS-3 uncalibrated phase delay estimation considering the intra-system bias

Intra-system biases (ISBs) between BDS-2 and BDS-3 are of critical importance when combining observations from the BDS-2 and BDS-3 systems, which is meaningful to fully take advantage of the BDS positioning capability. Meanwhile, ISBs should also be considered in the estimation of BDS uncalibrated phase delays (UPDs). In this research, we present a BDS-2/BDS-3 joint-processing scheme, as well as a method for estimating BDS UPDs. The characteristics of ISBs and the quality of BDS UPDs are analyzed based on 30-day data from 130 multi-GNSS experimental (MGEX) stations. Our results indicate that the ISBs are related to the type and version of the receiver. The ISBs can be regarded as constant across the course of a given day, and the mean standard deviation (STD) values of ISBs over one month for different types of receivers are generally within 0.2 m. Moreover, to assess the quality of UPD products, the residuals of the estimated UPDs and the utilization rates of the observation data are computed. The results show that the quality of BDS UPDs can be improved by correcting the satellite-induced pseudo-range variations, and by estimating the wide-lane (WL) UPD difference between BDS-2 and BDS-3. The average RMS values of the estimated residuals of WL UPD and narrow-lane (NL) UPD are 0.07 and 0.09 cycles, respectively; moreover, the utilization rate of the observation data of WL UPD and NL UPD can reach above 90 %. The performance of BDS precise point positioning (PPP) and PPP ambiguity resolution (PPP-AR) is analyzed in terms of positioning accuracy and convergence performance in both the static and kinematic modes. Compared with PPP ambiguity-float solutions, the positioning accuracy of PPP-AR is significantly improved, especially in the east direction. The impact of ISBs on PPP and PPP-AR is also analyzed, and the results indicate that ISBs can improve the convergence speed of float PPP, but can be disregarded in PPP-AR.     

Using only observation station data for PPP ambiguity resolution by UPD estimation

This article proposes a new method for uncalibrated phase delay (UPD) estimation to improve the accuracy of precise point positioning (PPP), which uses only observation station data. This means that the station used to generate the UPDs is the same station to which they are applied. First, dual-frequency observation equations based on a raw PPP model are developed. Then, the UPDs are calculated from integer linear combinations of float ambiguities. Third, with the UPD corrections, the least-squares ambiguity decorrelation adjustment (LAMBDA) method is utilized to obtain the integer ambiguities. Since only observation station data are used for UPD estimation, the partial ambiguity resolution (PAR) method is adopted to increase the possibility of finding a subset of integer ambiguities. The UPD estimation and ambiguity resolution are performed in each epoch. To obtain the correct integer ambiguity, the ratio test and success rate (bootstrapping) are used to evaluate the estimated integer ambiguity. Finally, by treating the integer ambiguities as constants, fixed solutions can be obtained. Quality control is also applied throughout the entire data processing procedure to obtain high quality float and fixed solutions. Data from 22 stations of the International Global Navigation Satellite System (GNSS) Service (IGS) in East Asia on day of year (DOY) 206, 2017, are used to verify the feasibility of this method. The experimental results show that compared with the float solution, the proposed method can significantly improve the accuracy in the east, north and up directions by 24%, 21% and 18% for static PPP and 36%, 18% and 34% for dynamic PPP, respectively. However, the accuracy of the proposed method is still lower than that of the fixed solutions obtained by the PRIDE-PPPAR software, in which the fractional cycle bias is computed based on reference network data. These findings sufficiently show that the proposed method can offer better solution accuracy than the float solution. However, the quality of the UPDs estimated only from observation station data is not as good as that of the estimates obtained based on reference network data.     

Performance analysis of PPP ambiguity resolution with UPD products estimated from different scales of reference station networks

Integer ambiguity fixing with uncalibrated phase delay (UPD) products can significantly shorten the initialization time and improve the accuracy of precise point positioning (PPP). Since the tracking arcs of satellites and the behavior of atmospheric biases can be very different for the reference networks with different scales, the qualities of corresponding UPD products may be also various. The purpose of this paper is to comparatively investigate the influence of different scales of reference station networks on UPD estimation and user ambiguity resolution. Three reference station networks with global, wide-area and local scales are used to compute the UPD products and analyze their impact on the PPP-AR. The time-to-first-fix, the unfix rate and the incorrect fix rate of PPP-AR are analyzed. Moreover, in order to further shorten the convergence time for obtaining precise positioning, a modified partial ambiguity resolution (PAR) and corresponding validation strategy are presented. In this PAR method, the ambiguity subset is determined by removing the ambiguity one by one in the order of ascending elevations. Besides, for static positioning mode, a coordinate validation strategy is employed to enhance the reliability of the fixed coordinate. The experiment results show that UPD products computed by smaller station network are more accurate and lead to a better coordinate solution; the PAR method used in this paper can shorten the convergence time and the coordinate validation strategy can improve the availability of high precision positioning.     

Performance assessment of RTPPP positioning with SSR corrections and PPP-AR positioning with FCB for multi-GNSS from MADOCA products

The state-space representation (SSR) product of satellite orbit and clock is one of the most essential corrections for real-time precise point positioning (RTPPP). When it comes to PPP ambiguity resolution (PPP-AR), the fractional cycle bias (FCB) matters. The Japan Aerospace Exploration Agency (JAXA) has developed a multi-GNSS (i.e., global navigation satellite system) advanced demonstration tool for orbit and clock analysis (MADOCA), providing free and precise orbit and clock products. Because of the shortage of relevant studies on performance evaluation, this paper focuses on the performance assessment of RTPPP and PPP-AR by real-time and offline MADOCA products. To begin with, the real-time MADOCA products are evaluated by comparing orbit and clock with JAXA final products, which gives an objective impression of the correction. Second, PPP tests in static and simulated kinematic mode are conducted to further verify the quality of real-time MADOCA products. Finally, the offline MADOCA products are assessed by PPP and PPP-AR comparisons. The results are as follows: (1) Orbit comparisons produced an average error of about 0.04–0.13 m for the global positioning system (GPS), 0.14–0.16 m for the global navigation satellite system (GLONASS), and 0.07–0.08 m for the quasi-zenith satellite system (QZSS). The G15 satellite had the most accurate orbit, with a difference of 0.04 m between the JAXA orbit products and MADOCA’s counterpart, while the R07 satellite had the least accurate orbit with a difference of 0.16 m. Clock products had an accuracy of 0.4–1.3 ns for GPS, 1.4–1.6 ns for GLONASS, and 0.7–0.8 ns for QZSS in general. The G15 satellite had the most accurate clock with a difference of only 0.40 ns between the JAXA clock products and MADOCA products, and the R07 satellite had the least accurate clock with a difference of 1.55 ns. The orbit and clock products for GLONASS performed worse than those of GPS and QZSS. (2) After convergence, the positioning accuracy was 3.0–8.1 cm for static PPP and 8.1–13.7 cm for kinematic PPP when using multi-GNSS observations and precise orbit and clock products. The PFRR station performed the good performance both in static and kinematic mode with an accuracy of 2.99 cm and 8.08 cm, respectively, whereas the CPNM station produced the worst static performance with an error of 8.09 cm, and the ANMG station produced the worst kinematic performance with a counterpart of 13.69 cm. (3) The PPP-AR solution was superior to the PPP solution, given that, with respect to PPP, post-processing PPP-AR improved the positioning accuracy and convergence time by 13–32 % (3–89 %) in GPS-only mode by 2–15 % (5–60 %) in GPS/QZSS mode. Thus, we conclude that the current MADOCA products can provide SSR corrections and FCB products with positioning accuracy at the decimeter or even centimeter level, which could meet the demands of the RTPPP and PPP-AR solutions.     

An improved approach to model regional ionosphere and accelerate convergence for precise point positioning

Given the severe effects of the ionosphere on global navigation satellite system (GNSS) signals, single-frequency (SF) precise point positioning (PPP) users can only achieve decimeter-level positioning results. Ionosphere-free combinations can eliminate the majority of ionospheric delay, but increase observation noise and slow down dual-frequency (DF) PPP convergence. In this paper, we develop a regional ionosphere modeling and rapid convergence approach to improve SF PPP (SFPPP) accuracy and accelerate DF PPP (DFPPP) convergence speed. Instead of area model, ionospheric delay is modeled for each satellite to be used as a priori correction. With the ionospheric, wide-lane uncalibrated phase delay (UPD) and residuals satellite DCBs product, the wide-lane observations for DF users change to be high-precision pseudorange observations. The validation of a continuously operating reference station (CORS) network was analyzed. The experimental results confirm that the approach considerably improves the accuracy of SFPPP. For DF users, convergence time is substantially reduced.     

Performance improvement of real-time PPP ambiguity resolution using a regional integer clock

Obtaining reliable GNSS uncalibrated phase delay (UPD) or integer clock products is the key to achieving ambiguity-fixed solutions for real-time (RT) precise point positioning (PPP) users. However, due to the influence of RT orbit errors, the quality of UPD/integer clock products estimated with a globally distributed GNSS network is difficult to ensure, thereby affecting the ambiguity resolution (AR) performance of RT-PPP. In this contribution, by fully utilising the consistency of orbital errors in regional GNSS network coverage areas, a method is proposed for estimating regional integer clock products to compensate for RT orbit errors. Based on Centre National d’Études Spatiales (CNES) RT precise products, the regional GPS/BDS integer clock was estimated with a CORS network in the west of China. Results showed that the difference between the estimated regional and CNES global integer clock/bias products was generally less than 5 cm for GPS, whereas clock differences of greater than 10 cm were observed for BDS due to the large RT orbit error. Compared with PPP using global integer clock/bias products, the AR performance of PPP using the regional integer clock was obviously improved for four rover stations. For single GPS, the horizontal and vertical accuracies of ambiguity-fixed PPP solutions were improved by 56.2% and 45.3% on average, respectively, whereas improvements of 67.5% and 50.5% in the horizontal and vertical directions, respectively, were observed for the combined GPS/BDS situation. Based on a regional integer clock, the RMS error of a kinematic ambiguity-fixed PPP solution in the horizontal direction could reach 0.5 cm. In terms of initialisation time, the average time to first fix (TTFF) in combined GPS/BDS PPP was shortened from 18.2 min to 12.7 min. In view of the high AR performance realised with the use of regional integer clocks, this method can be applied to scenarios that require high positioning accuracy, such as deformation monitoring.     

Multi-GNSS contributions to differential code biases determination and regional ionospheric modeling in China

Due to the limited number and uneven distribution globally of Beidou Satellite System (BDS) stations, the contributions of BDS to global ionosphere modeling is still not significant. In order to give a more realistic evaluation of the ability for BDS in ionosphere monitoring and multi-GNSS contributions to the performance of Differential Code Biases (DCBs) determination and ionosphere modeling, we select 22 stations from Crustal Movement Observation Network of China (CMONOC) to assess the result of regional ionospheric model and DCBs estimates over China where the visible satellites and monitoring stations for BDS are comparable to those of GPS/GLONASS. Note that all the 22 stations can track the dual- and triple-frequency GPS, GLONASS, and BDS observations. In this study, seven solutions, i.e., GPS-only (G), GLONASS-only (R), BDS-only (C), GPS + BDS (GC), GPS + GLONASS (GR), GLONASS + BDS (RC), GPS + GLONASS + BDS (GRC), are used to test the regional ionosphere modeling over the experimental area. Moreover, the performances of them using single-frequency precise point positioning (SF-PPP) method are presented. The experimental results indicate that BDS has the same ionospheric monitoring capability as GPS and GLONASS. Meanwhile, multi-GNSS observations can significantly improve the accuracy of the regional ionospheric models compared with that of GPS-only or GLONASS-only or BDS-only, especially over the edge of the tested region which the accuracy of the model is improved by reducing the RMS of the maximum differences from 5–15 to 2–3 TECu. For satellite DCBs estimates of different systems, the accuracy of them can be improved significantly after combining different system observations, which is improved by reducing the STD of GPS satellite DCB from 0.243 to 0.213, 0.172, and 0.165 ns after adding R, C, and RC observations respectively, with an increment of about 12.3%, 29.4%, and 32.2%. The STD of GLONASS satellite DCB improved from 0.353 to 0.304, 0.271, and 0.243 ns after adding G, C, and GC observations, respectively. The STD of BDS satellite DCB reduced from 0.265 to 0.237, 0.237 and 0.229 ns with the addition of G, R and GR systems respectively, and increased by 10.6%, 10.4%, and 13.6%. From the experimental positioning result, it can be seen that the regional ionospheric models with multi-GNSS observations are better than that with a single satellite system model.     

Towards PPP-RTK: Ambiguity resolution in real-time precise point positioning

Integer ambiguity resolution at a single station can be achieved by introducing predetermined uncalibrated phase delays (UPDs) into the float ambiguity estimates of precise point positioning (PPP). This integer resolution technique has the potential of leading to a PPP-RTK (real-time kinematic) model where PPP provides rapid convergence to a reliable centimeter-level positioning accuracy based on an RTK reference network. Nonetheless, implementing this model is technically subject to how rapidly we can fix wide-lane ambiguities, stabilize narrow-lane UPD estimates, and achieve the first ambiguity-fixed solution. To investigate these issues, we used 7 days of 1-Hz sampling GPS data at 91 stations across Europe. We find that at least 10 min of observations are required for most receiver types to reliably fix about 90% of wide-lane ambiguities corresponding to high elevations, and over 20 min to fix about 90% of those corresponding to low elevations. Moreover, several tens of minutes are usually required for a regional network before a narrow-lane UPD estimate stabilizes to an accuracy of far better than 0.1 cycles. Finally, for hourly data, ambiguity resolution can significantly improve the accuracy of epoch-wise position estimates from 13.7, 7.1 and 11.4 cm to 0.8, 0.9 and 2.5 cm for the East, North and Up components, respectively, but a few tens of minutes is required to achieve the first ambiguity-fixed solution. Therefore, from the timeliness aspect, our PPP-RTK model currently cannot satisfy the critical requirement of instantaneous precise positioning where ambiguity-fixed solutions have to be achieved within at most a few seconds. However, this model can still be potentially applied to some near-real-time remote sensing applications, such as the GPS meteorology.     

Mitigation of receiver biases in ionospheric observables from PPP with ambiguity resolution

PPP (Precise Point Positioning) is a GNSS (Global Navigation Satellite Systems) positioning method that requires SSR (State Space Representation) corrections in order to provide solutions with an accuracy of centimetric level. The so-called RT-PPP (Real-time PPP) is possible thanks to real-time precise SSR products, for orbits and clocks, provided by IGS (International GNSS Service) and its associate analysis centers such as CNES (Centre National d'Etudes Spatiales). CNES SSR products also enable RT-PPP with integer ambiguity resolution. In GNSS related literature, PPP with ambiguity resolution (PPP-AR) in real-time is often referred as PPP-RTK (PPP – Real Time Kinematic). PPP-WIZARD (PPP - With Integer and Zero-difference Ambiguity Resolution Demonstrator) is a software that is made available by CNES. This software is capable of performing PPP-RTK. It estimates slant ionospheric delays and other GNSS positioning parameters. Since ionospheric effects are spatially correlated by GNSS data from active networks, it is possible to model and provide ionospheric delays for any position in the network coverage area. The prior knowledge ionospheric delays can reduce positioning convergence for PPP-RTK users. Real-time ionospheric models could benefit from highly precise ionospheric delays estimated in PPP-AR. In this study, we demonstrate that ionospheric delays obtained throughout PPP-AR estimation are actu ally ionospheric observables. Ionospheric observables are biased by an order of few meters caused by the receiver hardware biases. These biases prohibit the use of PPP-WIZARD ionospheric delays to produce ionospheric models. Receiver biases correction is essential to provide ionospheric delays while using PPP-AR based ionospheric observables. In this contribution, a method was implemented to estimate and mitigate receiver hardware biases influence on slant ionospheric observables from PPP-AR. In order to assess the proposed approach, PPP-AR data from 12 GNSS stations were processed over a two-month period (March and April 2018). A comparison between IGS ionospheric products and PPP-AR based ionospheric observables corrected for receiver biases, resulted in a mean of differences of −39 cm and 51 cm standard deviation. The results are consistent with the accuracy of the IGS ionospheric products, 2–8 TECU, considering that 1 TECU is ~16 cm in L1. In another analysis, a comparison of ionospheric delays from 5 pairs of short baselines GNSS stations found an agreement of 0.001 m in mean differences with 22 cm standard deviation after receiver biases were corrected. Therefore, the proposed solution is promising and could produce high quality (1–2 TECU) slant ionospheric delays. This product can be used in a large variety of modeling approaches, since ionospheric delays after correction are unbiased. These results indicate that the proposed strategy is promising, and could benefit applications that require accuracy of 1–2 TECU (~16–32 cm in L1).     

Comparison of convergence time and positioning accuracy among BDS,GPS and BDS/GPS precise point positioning with ambiguity resolution

Precise point positioning (PPP) usually takes about 30?min to obtain centimetre-level accuracy, which greatly limits its application. To address the drawbacks of convergence speed and positioning accuracy, we develop a PPP model with integrated GPS and BDS observations. Based on the method, stations with global coverage are selected to estimate the fractional cycle bias (FCB) of GPS and BDS. The short-term and long-term time series of wide-lane (WL) FCB, and the single day change of narrow-lane (NL) FCB are analysed. It is found that the range of GPS and BDS non-GEO (IGSO and MEO) WL FCB is stable at up to a 30-day-time frame. At times frame of up to 60?days, the stability is reduced a lot. Whether for short-term or long-term, the changes in the BDS GEO WL FCB are large. Moreover, BDS FCB sometimes undergoes a sudden jump. Besides, 17 and 10 stations were used respectively to investigate the convergence speed and positioning errors with six strategies: BDS ambiguity-float PPP (Bfloat), GPS ambiguity-float PPP (Gfloat), BDS/GPS ambiguity-float PPP (BGfloat), BDS ambiguity-fixed PPP (Bfix), GPS ambiguity-fixed (Gfix), and BDS/GPS ambiguity-fixed (BGfix). The average convergence speed of the ambiguity-fixed solution is greatly improved compared with the ambiguity-float solution. In terms of the average convergence time, the Bfloat is the longest and the BGfix is the shortest among these six strategies. Whether for ambiguity-float PPP or ambiguity-fixed PPP, the convergence reduction time in three directions for the combined system is the largest compared with the single BDS. The average RMS value of the Bfix in three directions (easting (E), northing (N), and up (U)) are 2.0?cm, 1.5?cm, and 5.9?cm respectively, while those of the Gfix are 0.8?cm, 0.5?cm, and 1.7?cm. Compared with single system, the BDS/GPS combined ambiguity-fixed system (BGfix) has the fastest convergence speed and the highest accuracy, with average RMS as 0.7?cm, 0.5?cm, and 1.9?cm for the E, N, U components, respectively.     

Ambiguity resolution in precise point positioning with hourly data for global single receiver

Integer ambiguity resolution (IAR) can improve precise point positioning (PPP) performance significantly. IAR for PPP became a highlight topic in global positioning system (GPS) community in recent years. More and more researchers focus on this issue. Progress has been made in the latest years. In this paper, we aim at investigating and demonstrating the performance of a global zero-differenced (ZD) PPP IAR service for GPS users by providing routine ZD uncalibrated fractional offsets (UFOs) for wide-lane and narrow-lane. Data sets from all IGS stations collected on DOY 1, 100, 200 and 300 of 2010 are used to validate and demonstrate this global service. Static experiment results show that an accuracy better than 1 cm in horizontal and 1–2 cm in vertical could be achieved in ambiguity-fixed PPP solution with only hourly data. Compared with PPP float solution, an average improvement reaches 58.2% in east, 28.3% in north and 23.8% in vertical for all tested stations. Results of kinematic experiments show that the RMS of kinematic PPP solutions can be improved from 21.6, 16.6 and 37.7 mm to 12.2, 13.3 and 34.3 mm for the fixed solutions in the east, north and vertical components, respectively. Both static and kinematic experiments show that wide-lane and narrow-lane UFO products of all satellites can be generated and provided in a routine way accompanying satellite orbit and clock products for the PPP user anywhere around the world, to obtain accurate and reliable ambiguity-fixed PPP solutions.     

The impact of orbital errors on the estimation of satellite clock errors and PPP

Precise satellite orbit and clocks are essential for providing high accuracy real-time PPP (Precise Point Positioning) service. However, by treating the predicted orbits as fixed, the orbital errors may be partially assimilated by the estimated satellite clock and hence impact the positioning solutions. This paper presents the impact analysis of errors in radial and tangential orbital components on the estimation of satellite clocks and PPP through theoretical study and experimental evaluation. The relationship between the compensation of the orbital errors by the satellite clocks and the satellite-station geometry is discussed in details. Based on the satellite clocks estimated with regional station networks of different sizes (∼100, ∼300, ∼500 and ∼700 km in radius), results indicated that the orbital errors compensated by the satellite clock estimates reduce as the size of the network increases. An interesting regional PPP mode based on the broadcast ephemeris and the corresponding estimated satellite clocks is proposed and evaluated through the numerical study. The impact of orbital errors in the broadcast ephemeris has shown to be negligible for PPP users in a regional network of a radius of ∼300 km, with positioning RMS of about 1.4, 1.4 and 3.7 cm for east, north and up component in the post-mission kinematic mode, comparable with 1.3, 1.3 and 3.6 cm using the precise orbits and the corresponding estimated clocks. Compared with the DGPS and RTK positioning, only the estimated satellite clocks are needed to be disseminated to PPP users for this approach. It can significantly alleviate the communication burdens and therefore can be beneficial to the real time applications.     

The GFZ real-time GNSS precise positioning service system and its adaption for COMPASS

Motivated by the IGS real-time Pilot Project, GFZ has been developing its own real-time precise positioning service for various applications. An operational system at GFZ is now broadcasting real-time orbits, clocks, global ionospheric model, uncalibrated phase delays and regional atmospheric corrections for standard PPP, PPP with ambiguity fixing, single-frequency PPP and regional augmented PPP. To avoid developing various algorithms for different applications, we proposed a uniform algorithm and implemented it into our real-time software. In the new processing scheme, we employed un-differenced raw observations with atmospheric delays as parameters, which are properly constrained by real-time derived global ionospheric model or regional atmospheric corrections and by the empirical characteristics of the atmospheric delay variation in time and space. The positioning performance in terms of convergence time and ambiguity fixing depends mainly on the quality of the received atmospheric information and the spatial and temporal constraints. The un-differenced raw observation model can not only integrate PPP and NRTK into a seamless positioning service, but also syncretize these two techniques into a unique model and algorithm. Furthermore, it is suitable for both dual-frequency and sing-frequency receivers. Based on the real-time data streams from IGS, EUREF and SAPOS reference networks, we can provide services of global precise point positioning (PPP) with 5–10 cm accuracy, PPP with ambiguity-fixing of 2–5 cm accuracy, PPP using single-frequency receiver with accuracy of better than 50 cm and PPP with regional augmentation for instantaneous ambiguity resolution of 1–3 cm accuracy. We adapted the system for current COMPASS to provide PPP service. COMPASS observations from a regional network of nine stations are used for precise orbit determination and clock estimation in simulated real-time mode, the orbit and clock products are applied for real-time precise point positioning. The simulated real-time PPP service confirms that real-time positioning services of accuracy at dm-level and even cm-level is achievable with COMPASS only.     

Evaluation of rapid phase clock/bias products for PPP ambiguity resolution and its application to the M7.1 2019 Ridgecrest,California earthquake

Precise point positioning with ambiguity resolution (PPP-AR) is a useful tool for high-precision geodetic and geophysical applications, while phase bias products are the prerequisite to implement PPP-AR. Wuhan University has been providing the final (the best operationally post-processing solution based) phase clock/bias products with a latency of two weeks since March of 2019, while a dedicated open-source software package PRIDE PPP-AR is released to leverage these products for high-precision positioning. In order to satisfy some both time and precision critical applications, such as rapid earthquake response, Wuhan University also released rapid (with comparable quality but with much shorter delivery latency) phase clock/bias products with a latency of less than 24 h and updated PRIDE PPP-AR in July 2019. We first introduce the phase clock/bias generation and validation schemes and the maintenance of routine products provision. Then, with 14 days (July 2 to July 15 in 2019) of GPS data collected from 146 globally distributed IGS (International GNSS Service) stations, we evaluated the positioning performance of the rapid products with respect to their final counterparts. It is found that positioning precision of PPP-AR using rapid products is comparable to that using final products, especially in kinematic positioning mode. When rapid products are used, the RMS of PPP-AR in static mode with respect to IGS weekly solutions can reach 1.7 mm, 1.8 mm and 5.5 mm in the east, north and up components, respectively. Furthermore, the RMS of epoch-wise positions with respect to daily solutions for the east, north and up components are 0.51 cm, 0.57 cm and 1.51 cm for PPP-AR with rapid products in kinematic mode. It demonstrates that the rapid phase clock/bias products can sufficiently meet the precision requirement of most geodetic and geophysical applications yet with much shorter time delay. Finally, we study the July 6th M7.1 2019 Ridgecrest, California earthquake using the rapid phase clock/bias products and demonstrate their comparable performance against the final products.     

Differential code bias estimation based on uncombined PPP with LEO onboard GPS observations

Differential Code Bias (DCB) is an essential correction that must be provided to the Global Navigation Satellite System (GNSS) users for precise position determination. With the continuous deployment of Low Earth Orbit (LEO) satellites, DCB estimation using observations from GNSS receivers onboard the LEO satellites is drawing increasing interests in order to meet the growing demands on high-quality DCB products from LEO-based applications, such as LEO-based GNSS signal augmentation and space weather research. Previous studies on LEO-based DCB estimation are usually using the geometry-free combination of GNSS observations, and it may suffer from significant leveling errors due to non-zero mean of multipath errors and short-term variations of receiver code and phase biases. In this study, we utilize the uncombined Precise Point Positioning (PPP) model for LEO DCB estimation. The models for uncombined PPP-based LEO DCB estimation are presented and GPS observations acquired from receivers onboard three identical Swarm satellites from February 1 to 28, 2019 are used for the validation. The results show that the average Root Mean Square errors (RMS) of the GPS satellite DCBs estimated with onboard data from each of the three Swarm satellites using the uncombined PPP model are less than 0.18 ns when compared to the GPS satellite DCBs obtained from IGS final daily Global Ionospheric Map (GIM) products. Meanwhile, the corresponding average RMS of GPS satellite DCBs estimated with the conventional geometry-free model are 0.290, 0.210, 0.281 ns, respectively, which are significantly larger than those obtained with the uncombined PPP model. It is also noted that the estimated GPS satellite DCBs by Swarm A and C satellites are highly correlated, likely attributed to their similar orbit type and space environment. On the other hand, the Swarm receiver DCBs estimated with uncombined PPP model, with Standard Deviation (STD) of 0.065, 0.037 and 0.071 ns, are more stable than those obtained from the official Swarm Level 2 products with corresponding STD values of 0.115, 0.101, and 0.109 ns, respectively. The above indicates that high-quality DCB products can be estimated based on uncombined PPP with LEO onboard observations.     

GNSS geodetic techniques for time and frequency transfer applications

We performed an initial analysis of the pseudorange data of the GIOVE-B satellite, one of the two experimental Galileo satellites currently in operation, for time transfer.¹ For this specific aim, software was developed to process the GIOVE-B raw pseudoranges and broadcast navigation messages collected by the Galileo Experimental Sensor Stations (GESS) tracking network, yielding station clock phase errors with respect to the Experimental Galileo System Time (EGST). The software also allows processing the Global Positioning System (GPS) P1 and P2 pseudorange data with broadcast navigation message collected at the same stations to obtain the station clock phase errors with respect to the GPS system time (GPST). Differencing these solutions between stations provides two independent means of GNSS time transfer. We compared these time transfer results with Precise Point Positioning (PPP) method applied to GPS data in combined carrier-phase and pseudorange mode as well as in pseudorange-only mode to show their relative merits. The PPP solutions in combined carrier-phase and pseudorange mode showed the least instability of the methods tested herein at all scales, at few parts in 10¹⁵ at 1 day for the stations processed, following a tau^−½ interval dependency. Conversely, the PPP solutions in pseudorange-only mode are an order of magnitude worst (few parts in 10¹⁴ at 1 day for the stations processed) following a tau⁻¹ power-law, but slightly better than the single-satellite raw GPS time transfer solutions obtained using the developed software, since the PPP least-squares solution effectively averages the pseudorange noise. The pseudorange noise levels estimated from PPP pseudorange residuals and from clock solution comparisons are largely consistent, providing a validation of our software operation. The raw GIOVE-B time transfer, as implemented in this work, proves to be slightly better than single-satellite raw GPS satellite time transfer, at least in the medium term. However, one of the processed stations shows a combined GPS P1 and P2 pseudorange noise level at 2 m, a factor 2 worst than usually seen for geodetic receivers, so the GPS time transfer results may not be at their best for the cases processed. Over the short term, the GPS single-satellite time transfer instability outperforms the GIOVE-B by an order of magnitude at 1 s interval, which would be due to the different characteristics of the tracking loop filters for GPS P1 and P2 on one hand and the GIOVE-B signals on the other. Even at this preliminary stage and using an experimental satellite system, results show that the GIOVE-B (and hence Galileo) signals offer interesting perspectives for high precision time transfer between metrological laboratories.     

Evaluation on real-time dynamic performance of BDS in PPP,RTK, and INS tightly aided modes

Since China’s BeiDou satellite navigation system (BDS) began to provide regional navigation service for Asia-Pacific region after 2012, more new generation BDS satellites have been launched to further expand BDS’s coverage to be global. In this contribution, precise positioning models based on BDS and the corresponding mathematical algorithms are presented in detail. Then, an evaluation on BDS’s real-time dynamic positioning and navigation performance is presented in Precise Point Positioning (PPP), Real-time Kinematic (RTK), Inertial Navigation System (INS) tightly aided PPP and RTK modes by processing a set of land-borne vehicle experiment data. Results indicate that BDS positioning Root Mean Square (RMS) in north, east, and vertical components are 2.0, 2.7, and 7.6?cm in RTK mode and 7.8, 14.7, and 24.8?cm in PPP mode, which are close to GPS positioning accuracy. Meanwhile, with the help of INS, about 38.8%, 67.5%, and 66.5% improvements can be obtained by using PPP/INS tight-integration mode. Such enhancements in RTK/INS tight-integration mode are 14.1%, 34.0%, and 41.9%. Moreover, the accuracy of velocimetry and attitude determination can be improved to be better than 1?cm/s and 0.1°, respectively. Besides, the continuity and reliability of BDS in both PPP and RTK modes can also be ameliorated significantly by INS during satellite signal missing periods.     

三点测距副站技术

设计和研制的两个副站（乌鲁木齐站和广州站）和北京的主站相互配合形成三点测距系统,可以完成对风云二号卫星的测距定轨任务。文章着重介绍了副站的组成、作用和功能技术指标等。它的设计方法与国外同类技术相比颇具特色。经过对日本气象卫星进行的几年跟踪测试,及最后通过对风云二号卫星执行任务的验证,确认了副站方案的可行性,设计的合理性。     

Assessing the performance of BDS-3 for multi-GNSS static and kinematic PPP-AR

As of 2021, a total of four different GNSS constellations – namely, GPS, GLONASS, Galileo, and BDS-3 – can be used with Full Operational Capability (FOC). In this work, the contribution of BDS-3 FOC to GPS + GLONASS + Galileo (GRE) PPP-AR is investigated, considering the three different cut-off angles (7°, 30°, and 45°) and different lengths of static observation sessions (24-, 12-, 6-, 3-, 1-, 0.5-, 0.25-hour). The data of 31 IGS-MGEX stations is processed with GRE PPP-AR and GREC3 (GPS + GLONASS (using float mode) + Galileo + BDS-3) PPP-AR modes. The results showed that BDS-3 degraded the horizontal (except for 24-h sessions) and vertical accuracy of static GRE PPP-AR solutions regardless of the elevation cutoff angle and observation time. The kinematic results showed that BDS-3 significantly contributed to the accuracy of GRE kinematic PPP-AR for 30° and 45° cutoff angles. The convergence time analysis showed that BDS-3 only contributes to GRE kinematic PPP-AR for the vertical component.     

观测资料和卫星钟差对PPP参数收敛影响分析

在GPS 单点定位中, 参数解算的收敛时间和收敛稳定性是重要的研究内容之一, 影响收敛时间和收敛稳定性的因素很多, 本文主要就观测资料的不同采样间隔、卫星钟差资料的不同采样间隔、不同的定位精度要求对精密单点定位中参数收敛时间的影响进行了深入的分析探讨, 以中国上海GPS综合应用网中的12个测站资料为例, 分析了采样间隔、定位精度要求与收敛时间的关系, 并对不同采样间隔的收敛时间进行了统计分析, 得出一些初步结论.