共查询到20条相似文献,搜索用时 484 毫秒
1.
筒形件模环旋压隆起和旋压力的有限元模拟分析 总被引:1,自引:0,他引:1
在分析筒形件强力模环旋压工艺变形特点的基础上,采用三维弹塑性有限元法对筒形件模环旋压进行了数值模拟,分析了旋压成形时的应力分布、旋压成形中的隆起现象及工艺参数对隆起和旋压力的影响.结果表明,在所描述的工艺条件下,采用成形角为20~25,牵引速度范围为0.4~0.6mm/s是合理的.模拟分析结果为模环旋压工艺参数的优化提供了依据. 相似文献
2.
3.
4.
通过对铌钨合金性能的研究,得到了铌钨合金一次旋压最大减薄率,采用变厚度平板旋压毛坯,合理分布两次剪切旋压变形量和各点壁厚变薄率,控制旋压过程,应用仿真软件对翻边成形进行仿真,掌握了薄壁大尺寸铌钨合金喷管精密旋压及翻边成形技术. 相似文献
5.
6.
通过对某型号固体火箭发动机超薄壁燃烧室壳体旋压工艺研究,分析D6AC材料筒形件在超薄壁旋压生产中壁厚、圆度、直线度的控制以及前期毛坯设计问题。从工艺角度主要解决生产中遇到的产品质量问题,兼顾各个工艺方案在不同生产阶段的适用情况。 相似文献
7.
超长薄壁带台阶筒体在其加工上有较大难度 ,是适合用强力旋压加工完成的典型零件。通过工艺攻关 ,制作旋压工装 ,确定旋压方式、旋压方案、合理的旋压参数 ,旋压出了合格的筒体制件。该工艺方法已运用于正常的批量生产 ,制件精度良好 ,符合所有要求。 相似文献
8.
9.
应用电阻应变片测力方法,分析了筒形件强旋时旋轮受力曲线。该曲线能够真实地反映旋压时的堆积,工件扭转失稳和过旋及三旋轮受力不均,起旋冲击等现象。通过对受力曲线的分析,改善了旋压工艺,提高了产品质量。 相似文献
10.
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
13.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
14.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
15.
16.
金属网由于柔韧性好、使用方便等优势而在电缆屏蔽工程上得到广泛应用。本文对电缆用的金属网屏蔽效能进行工程计算,通过计算,对金属网不同材料、不同规格、单层与双层屏蔽及有缝隙情况下的屏蔽效能进行比较与分析,对工程应用有一定的指导意义。 相似文献
17.
18.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
19.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献