直连式三体绳系卫星姿态鲁棒最优跟踪控制

 针对存在参数不确定性以及外部有界干扰的直连式三体旋转绳系卫星系统姿态跟踪控制问题,提出了一种分布式鲁棒最优控制方法。该方法首先针对单体绳系卫星姿态模型,在不考虑参数不确定性和干扰的条件下,应用Hamilton-Jacobi-Bellman方程设计了最优控制器;接着,考虑到实际系统存在参数不确定性和干扰,采用自适应与鲁棒误差积分方法在线学习参数不确定性和有界干扰,与最优控制器结合设计了鲁棒最优控制器,使闭环系统满足了性能指标达到最小的要求,并应用Lyapunov稳定性定理证明了其闭环系统的渐近稳定性。进一步考虑到绳系卫星系统的运动同步性,将单体绳系卫星姿态控制器设计扩展至直连式三体绳系卫星姿态系统,设计了分布式鲁棒最优控制器。最后在MATLAB/Simulink平台上进行了仿真,验证了方法的可行性与有效性,表明其具有潜在的应用前景。     

Quick position determination using 1 or 2 LEO satellites

We describe an approach for a medium accuracy position determination of a user terminal (UT) on the Earth surface, using one or two low Earth orbit (LEO) satellites. The positioning approach is intended to meet the requirements of a worldwide personal communications system using LEO satellites. The basic two requirements are: (1) immediate positioning, and (2) horizontal position accuracy of the order of 10 km. Those requirements stem from the need of the system to know the user's approximate location before it connects his call. The approach makes use of the two-way communication with the UT, which can receive, transmit, and make its own measurements. Delay and Doppler measurements are used in order to enable instantaneous positioning with one satellite, and in order to achieve unambiguous positioning with two satellites. A simplified Globalstar satellite constellation and the expected Globalstar delay and frequency measurement accuracy are used to demonstrate the concept and to evaluate its performances     

多状态空间信息网络拓扑生成优化算法

依据空间信息网络（SIN）高动态性的特点，并考虑卫星工作的多状态特性，兼顾星间通信时延和拓扑抗毁性的要求，研究了多状态下空间信息网络拓扑生成及动态优化的问题。根据卫星星座的周期性，建立了一种卫星网络的拓扑周期表。综合卫星的可视性和连接度等约束条件，以网络平均和最大时延作为通信性能的优化目标，建立拓扑的多目标优化模型。提出一种改进的多目标模拟退火（IMOSA）算法，求解全局时延最优的卫星拓扑，并在考虑多状态情况下对链路进行优化，以满足网络高动态性。最后基于具有66颗低轨（LEO）的铱星星座进行仿真，研究表明：针对多状态条件下的铱星星座，该算法最大化减小了通信时延，得到抗毁性良好的拓扑结构，通信性能较之原有静态拓扑明显得到改善。     

HOI延迟对LEO卫星简化动力学POD的影响

通常使用无电离层(IF)线性组合(LC)消除低地球轨道(LEO)卫星简化动力学精密定轨(POD)一阶电离层延迟误差,忽略了高阶电离层(HOI)延迟误差。随着LEO卫星POD技术的发展,计算不同轨道高度的HOI延迟并探索其变化已成为进一步提高POD精度的重要手段。首先,使用国际参考电离层-2016(IRI-2016)和国际地磁参考场第13代(IGRF-13)模型,计算电离层穿刺点(IPP)位置和地磁场强度。其次,使用平滑星载GNSS数据计算电离层斜路径总电子含量(STEC)。然后,分别计算GOCE、GRACE-A和SWARM-A/B卫星的二阶和三阶电离层延迟。最后,评估了HOI延迟对LEO卫星重叠轨道分析、卫星激光测距(SLR)检核和精密科学轨道(PSO)比较结果的影响。实验结果表明：HOI延迟对LEO卫星简化动力学POD的影响大约在毫米至厘米的数量级上;HOI延迟对LEO卫星简化动力学POD外符合精度的影响分别达到0.92,0.22,0.21和0.18 mm;随着LEO卫星轨道高度的增加,HOI延迟对LEO卫星简化动力学POD的影响减小。     

星间链路数量受限的导航卫星网络链路分配问题

对星间链路数量非常有限、需要同时满足星间测距和星间通信需求的导航卫星网络的链路分配问题进行了研究。首先,分析了导航卫星网络的特点,并设计了一种基于有限状态自动机(FSA)的拓扑处理机制。然后,将星间测距需求作为一个约束,以星间通信的延时性能为优化目标,将导航卫星网络的链路分配问题建模为一个多目标优化问题。最后,针对建立的多目标优化问题,分别提出一种基于首次改善(FI)的本地搜索算法和基于模拟退火(SA)的启发式优化算法以对链路分配问题进行求解,并提出一种基于分支交换策略的新链路分配生成方法。仿真结果表明,通过FI算法和SA算法获得的优化链路分配的网络延时性能均得到了改进,且SA算法的性能要优于FI算法;同时,FSA的状态持续时间的减小有利于获得网络延时性能好的链路分配。     

Collocation of two GEO satellites and one inclined GSO satellite

Three collocation strategies are planned and analyzed for the cluster of two geostationary orbit (GEO) satellites and one inclined geosynchronous orbit (GSO) satellite in the same longitude control band of 116°E±0.05° . The longitudinal control bands are allocated for the two GEO satellites and one inclined GSO satellite with seven-day East/West station-keeping maneuver cycle. The latitudinal control bands are allocated for the two GEO satellites with fourteen-day North/South station-keeping maneuver cycle. One inclined GSO satellite is allowed for natural inclination drift. The coordinated eccentricity vector and inclination vector separation method is applied for the collocation, and the maneuver schedule is planned to minimize the operational load by avoiding simultaneous maneuvers. A total of six months of station-keeping maneuver simulations are performed for the three different strategies.     

全球卫星导航星座网络协议体系与运行模式

针对全球卫星导航星座网络建设初期或论证阶段所涉及的网络体系结构、协议体系及相关组网等技术问题,开展了基于导航星座星间链路构建空间信息网络的技术研究,分别提出了由子网、接入网、骨干网等节点及其相互之间星间、星地无线链路构成的分层网络系统结构,设计了兼容遥控、遥测、测量与网络交互支持等业务的基于IP over CCSDS(基于空间数据系统咨询委员会标准的空间链路承载互联网协议业务)的协议体系,给出了全系统基本通信业务运行模式等。与传统高轨卫星通信系统相比,该星座网络具有高覆盖、低时延、随遇接入等优点,可实现星座导航性能与中低轨及地面用户通信性能的全方位提升,相关结果对我国全球卫星导航星座网络技术研究具有一定的参考意义。     

Cross-layer design of LT codes and LDPC codes for satellite multimedia broadcast/multicast services

According to large coverage of satellites, there are various channel states in a satellite broadcasting network. In order to introduce an efficient rateless transmission method to satellite multimedia broadcasting/multicast services with finite-length packets, a cross-layer packet transmission method is proposed with Luby transform （LT） codes for efficiency in the network layer and low density parity check （LDPC） codes for reliability in the physical layer jointly. The codewords generated from an LT encoder are divided into finite-length packets, which are encoded by an LDPC encoder subsequently. Based on noise and fading effects of satellite channels, the LT packets received from an LDPC decoder either have no error or are marked as erased, which can be mod- eled as a binary erasure channels （BECs）. By theoretical analysis on LT parameters and LDPC parameters, the relationships between LDPC code rates in the physical layer and LT codes word lengths in the network layer are investigated. With tradeoffs between the LT codes word lengths and the LDPC code rates, optimized cross-layer solutions are achieved with a binary search algorithm. Verified by simulations, the proposed solution for cross-layer parameters design can provide the best transmission mode according to satellite states, so as to improve throughput performance for satellite multimedia transmission.     

Characterization of NAVSTAR GPS and GLONASS on-board clocks

Investigation into navigation satellite on board clock frequency references and performance are reported. The focus is on the stability of the clocks aboard the NAVSTAR GPS (Global Positioning System) and GLONASS satellites as well as those used by their respective maser control stations and associated time scales. Allan-variance techniques have been applied to determine the long-term time-domain behavior of satellite clocks in an attempt to identify different regions of power spectral density. Coupled with analysis of relative-frequency drift over a period of many weeks, this behavior allows the type of satellite onboard standard to be tentatively identified. The known nature of the GPS clocks has shown that the different types of clocks aboard the satellites (crystal, rubidium, and cesium) are distinguishable given a sufficient sample time. The same approach has been applied to the GLONASS satellites, and a comparison of the results obtained from GPS has allowed conjecture on the type of clock used by the GLONASS satellites. It appears that GLONASS has used clocks of the quality of rubidium atomic oscillators since at least 1986, and that the quality and performance of onboard standards have increased steadily with time. Some current satellites perform well enough in terms of frequency drift, flicker FM noise floor, and long-term stability to compare favorably with the cesium beam standards carried on NAVSTAR GPS satellites launched in 1983-84     

基于数字包络检波的RNSS通道时延标定方法

提出一种采用数字处理的时延测试方法,用于对导航卫星导航信号发射通道分数码片时延的精确测量。该方法是通过高速A/D（模/数）转换器,对导航卫星下行的BPSK（二进制相移键控）信号和卫星导航秒脉冲进行双通道采样,读取采样数据并进行数据处理。根据秒脉冲信号触发门限上升沿确定时延测量起点,对BPSK采样数据进行平方律检波,获取码片换相点,计算换相点和秒脉冲之间的分数码片时延,并进行滤波器时延校准,从而得到导航卫星发射链路的分数码片时延,该方法不需要进行伪随机信号的捕获和跟踪,测量精度主要取决于采样器采样率。通过在测试中使用一根校准电缆对该方法进行验证,验证结果表明,采用本文提出测试方法的测量误差优于0.3ns。     

附加双差模糊度网解约束的GNSS相位延迟估计

针对现有相位延迟估计方法未利用双差模糊度网解约束的特点,提出了一种附加双差模糊度网解约束的相位延迟估计方法。首先以整周双差模糊度网解为真值更新精密单点定位(PPP)估计的非差浮点模糊度,再通过网平差法估计未校正相位延迟(UPD)。实验结果表明,PPP双差模糊度与双差模糊度网解一致性好,其宽、窄巷中误差分别为0.07周和0.11周,误差大于1周的PPP双差模糊度主要出现在卫星初升阶段。约束改变了非差浮点模糊度,从而改变了参与UPD网平差的测站,使14%新升起卫星的窄巷UPD在短时间内较无约束有大于0.2周的差异。附加约束/无约束的全天星间单差UPD差异在大于99.9%的置信水平下满足零均值假设,表明整周双差模糊度网解约束方法与无约束方法估计UPD相关产品具有等效性。研究结果可为参考网非差模糊度解算和PPP与网络实时动态定位(RTK)的融合工作提供参考。     

C频段统一测控系统非相干测速功能探讨

针对目前国内C频段统一测控系统因不具备测速功能,在发遥控期间无法进行测距,导致其无法对卫星进行连续轨道测量的缺陷,提出了非相干测速方法。非相干测速利用卫星遥测信息中的上行载波多普勒信息以及地面站获取的下行载波多普勒信息,计算得到双向多普勒信息,对双向多普勒进行计算可获得连续的卫星运动速度信息。本文在理论上证明了这种方法的可行性,并以自旋式卫星同步控制过程中天地时延精确修正为例,说明了这种方法的应用价值。     

MEO/LEO双层卫星网络中层间链路的连接度分析

作为未来卫星移动通信系统的一个重要的研究方向,提出了一种由MEO卫星和LEO卫星共同组成的双层卫星网络(Double-Layer Satellite Network,DLSN),以更好为用户提供多媒体服务.作为多层卫星网络的一个重要的研究内容,连接不同高度上卫星的层间链路(Inter-Orbit-Links,IOLs)的特性对于整个DLSN网络的性能会有很大的影响.根据所设计的多层卫星网络的星座参数,通过对层间链路几何特性的研究,分析了多层卫星网络中MEO卫星与LEO卫星的连接度性能.采用计算机仿真的方法,给出了层间链路连接度的特性.结果表明,为了提高网络性能,在多层卫星网络中应按照一定参数有选择的建立层间链路,而不是简单的采用视距可见原则建立层间链路.     

Inter-satellite link augmented BeiDou-3 orbit determination for precise point positioning

Precise Point Positioning(PPP) requires precise products, including high-accuracy satellite orbit and clock parameters. It is impossible to obtain an orbit solution that is sufficiently accurate for PPP services with a regional tracking network; therefore, satellite orbits are usually estimated by a global tracking network with a large number of ground stations. However, it is expensive to build globally distributed stations. Fortunately, BeiDou-3 satellites carry an InterSatellite Link(ISL) pay...     

Spaceborne GPS receiver antenna phase center offset and variation estimation for the Shiyan 3 satellite

In determining the orbits of low Earth orbit (LEO) satellites using spaceborne GPS, the errors caused by receiver antenna phase center offset (PCO) and phase center variations (PCVs) are gradually becoming a major limiting factor for continued improvements to accuracy. Shiyan 3, a small satellite mission for space technology experimentation and climate exploration, was developed by China and launched on November 5, 2008. The dual-frequency GPS receiver payload delivers 1 Hz data and provides the basis for precise orbit determination within the range of a few centime-ters. The antenna PCO and PCV error characteristics and the principles influencing orbit determi-nation are analyzed. The feasibility of PCO and PCV estimation and compensation in different directions is demonstrated through simulation and in-flight tests. The values of receiver antenna PCO and PCVs for Gravity Recovery and Climate Experiment (GRACE) and Shiyan 3 satellites are estimated from one month of data. A large and stable antenna PCO error, reaching up to 10.34 cm in the z-direction, is found with the Shiyan 3 satellite. The PCVs on the Shiyan 3 satellite are estimated and reach up to 3.0 cm, which is slightly larger than that of GRACE satellites. Orbit validation clearly improved with independent k-band ranging (KBR) and satellite laser ranging (SLR) measurements. For GRACE satellites, the average root mean square (RMS) of KBR resid-uals improved from 1.01 cm to 0.88 cm. For the Shiyan 3 satellite, the average RMS of SLR resid-uals improved from 4.95 cm to 4.06 cm.     

飞轮被动减振卫星动力学建模及稳定性研究

为提高卫星的指向精度和稳定度,通常在飞轮系统中设计了被动减振器。而对于有敏捷机动要求的卫星,被动减振器的低刚度设计可能会破坏姿态控制系统的动态性能和稳定性。因此,针对飞轮减振情况,建立了卫星刚柔姿态动力学方程,用来准确分析卫星敏捷机动时的动态性能、稳定性问题以及飞轮扰动对卫星稳定度的影响。仿真结果表明,不合适的隔振器刚度设计将会影响指向的动态性能和稳定性,甚至诱发姿控系统失稳。     

面向高轨空间的北斗导航性能增强星座选型研究

由于高轨空间超出北斗卫星导航系统的正常服务区域,导航信号微弱、可见性差,难以实现高轨飞行器全程稳定可靠的导航定位服务。提出了以空间卫星为时空基准传递平台,向高轨空间区域发射导航信号,从而提高高轨飞行器导航性能的方法,并展开面向高轨空间的北斗导航性能增强星座选型研究。基于卫星可见性、精度衰减因子（DOP）、信号接收门限和所需增强卫星数目等评估指标,仿真分析了基于LEO星座、MEO星座和HEO星座的北斗导航增强性能。     

不同基准钟对BDS实时钟差估计的影响分析CSCD

BDS原始观测量是站星之间的相对时间延迟,在实时卫星钟差估计过程中需要引入一个基准钟,求解该基准约束下的钟差产品。基于两种不同的基准约束条件实时估计BDS卫星钟差,并从实时钟差的估计精度、钟差频率特性(频率漂移率、频率准确度、频率稳定度)及钟差预报精度等方面分析其对BDS实时钟差估计的影响。算例结果表明,在两种不同的基准模式下,估计得到的BDS实时卫星钟差性能基本一致,在实际使用中可根据情况采用不同的基准钟进行钟差估计,为BDS实时卫星钟差估计时基准钟的选择提供了参考。     

Wavelength dimensioning for wavelength-routed WDM satellite network

Internet and broadband applications driven by data traffic demand have become key dri-vers for satellite constellations. The key technology to satisfy the high capacity requirements between satellites is optical satellite networks by means of wavelength division multiplexing inter-satellite links (ISLs) with wavelength routing (WDM-OSN). Due to the limited optical amplifier bandwidth onboard the satellite, it is important to minimize the wavelength requirements to provi-sion requests. However, ISLs should be dynamically established and deleted for each satellite according to its visible satellites. Furthermore, different link assignments will result in different topologies, hence yielding different routings and wavelength assignments. Thus, a perfect match model-based link assignment scheme (LAS-PMM) is proposed to design an appropriate topology such that shorter path could be routed and less wavelengths could be assigned for each ISL along the path. Finally, simulation results show that in comparison to the regular Manhattan street net-work (MSN) topology, wavelength requirements and average end-to-end delay based on the topol-ogy generated by LAS-PMM could be reduced by 24.8%and 12.4%, respectively.     

分布式卫星干涉测高系统编队构形优化设计方法

 分布式卫星干涉合成孔径雷达（InSAR）编队构形设计是系统总体设计的关键问题。从系统测高性能优化角度出发，提出分布式InSAR编队优化设计一般方法，将其概括为求解一个优化问题，以主星带辅星群体制分布式InSAR为例建立目标函数，针对其星载双站、斜视、空间基线等特点建立测高精度与辅星轨道根数的关系，基于近似的相对运动数学模型对该优化问题进行简化，并采用遗传算法求解。在此基础上，对多颗卫星组成编队以提高系统测高性能提出了一种多星编队设计方法。仿真分析表明，经优化得到的编队测高性能要优于干涉车轮和钟摆编队，该结果验证了优化设计方法的有效性和正确性。