液体冲压发动机控制系统半实物仿真

运用小偏离线性化理论和Willoh方法，建立了液体冲压发动机和弹体动态数学模型。动态数学模型在微型计算上一体化运行，形成液体冲压发动机／弹体一体化实时数字仿真器。实时数字仿真器通过输入输出接口与液体冲压发动机的实际控制系统进行联接，组成液体冲压发动机、弹性和发动机控制系统半实物仿真系统。对冲压发动机飞行马赫数和控制 系统供油量的半实物仿真结果表明，系统能满足研制工作的需要。     

直升机燃油系统地面模拟试验中试验台转角与油面角的关系

为了在直升机燃油系统地面模拟试验中准确地模拟油面角，本文介绍了试验台转角与油面角的关系，并给出了转换结果，同时，提出了一种用油箱内增压来模拟过载的设想，使在模拟试验时，油泵供油更趋真实，通过简化计算，给出了确定气压力的方法和判断依据。     

Optimum FFT-based frequency acquisition with application toCOSPAS-SARSAT

In the case of a single sinusoid or multiple well-separated sinusoids, a coarse estimator consisting of a windowed Fourier transform followed by a fine estimator which is an interpolator is a good approximation to an optimal frequency acquisition and measurement algorithm. The design tradeoffs are described. It is shown that for the fine-frequency estimator a good method is to fit a Gaussian function to the fast-Fourier-transform (FFT) peak and its two neighbors. This method achieves a frequency standard deviation and a bias in the order of only a few percent of a bin. In the case of short-time stationarity, for a moderate number of averages and for an adaptive threshold detector, only between 0.5 and 1 dB is lost when averaging is traded off for FFT length, in contrast to the asymptotic result of 1.5 dB. The COSPAS-SARSAT satellite system for emergency detection and localization is used to illustrate the concepts. The algorithm is analyzed theoretically, and good agreement is found with test results     

A comparative study on acoustic damping induced by half-wave, quarter-wave, and Helmholtz resonators

The damping characteristics of three-type resonators, a half-wave, a quarter-wave, and a Helmholtz resonator are studied experimentally by adopting linear acoustic test. A quantitative acoustic property of sound absorption coefficient in a model enclosure with the resonators is measured and thereby, the acoustic-damping capacity of a resonator is characterized. For a comparative study on acoustic damping, the damping capacity of a half-wave resonator is compared with that of the other resonators. A half-wave and a quarter-wave resonators have the same damping mechanism, but a quarter-wave resonator has much larger damping capacity than a half-wave resonator with the same diameter of a single resonator. It is found that shorter length of a resonator has the advantage of longer one with respect to the damping capacity. The damping capacity of a Helmholtz resonator increases with cavity volume and does as the orifice length decreases. A Helmholtz resonator has the highest damping capacity of three-type resonators and a half-wave resonator has the lowest. Besides, a Helmholtz resonator requires the smallest number of resonators for optimal damping. The design criterion of each resonator on the optimal damping is provided by the normalized parameter of open-area ratio and the similarity behavior for the optimal damping is observed for various enclosure diameters.     

用于雷达波形的无损压缩编码

讨论了用算术编码实现波形数据的无损压缩。对波形数据进行无损压缩时 ,如果把每个可能的样本值看作一个符号 ,符号表会非常庞大 ,导致算法不可行。基于这种原因 ,本文用一个符号表示一定范围内波形数据 ,而不是单个波形数据 ,然后在此基础上设计了一种编码方案。先是无损线性预测 ,去除了波形数据之间的相关性。并假定产生的差值序列具有白功率谱 ,幅度服从高斯分布 ,第二步是算术编码。最后给出了对雷达回波数据进行压缩的实验结果。     

Detection of chi-square fluctuating targets in arbitrary clutter

In a recent paper, general expressions were derived for the density and cumulative probability functions of the amplitude of a linear matched-filter output given a nonfluctuating target in a clutter-limited environment. These expressions were based on the clutter amplitude density function. The results are extended to calculate the cumulative probability function of the output of a linear matched filter used to detect a chi-square fluctuating target in a clutter-limited environment. The resulting method is applied to a common radar clutter model, and experimental sonar data.     

Determination of a suitable set of loss models for centrifugal compressor performance prediction

Performance prediction in preliminary design stages of several turbomachinery components is a critical task in order to bring the design processes of these devices to a successful conclusion.In this paper,a review and analysis of the major loss mechanisms and loss models,used to determine the efficiency of a single stage centrifugal compressor,and a subsequent examination to determine an appropriate loss correlation set for estimating the isentropic efficiency in preliminary design stages of centrifugal compressors,were developed.Several semi-empirical correlations,commonly used to predict the efficiency of centrifugal compressors,were implemented in FORTRAN code and then were compared with experimental results in order to establish a loss correlation set to determine,with good approximation,the isentropic efficiency of single stage compressor.The aim of this study is to provide a suitable loss correlation set for determining the isentropic efficiency of a single stage centrifugal compressor,because,with a large amount of loss mechanisms and correlations available in the literature,it is difficult to ascertain how many and which correlations to employ for the correct prediction of the efficiency in the preliminary stage design of a centrifugal compressor.As a result of this study,a set of correlations composed by nine loss mechanisms for single stage centrifugal compressors,conformed by a rotor and a diffuser,are specified.     

雷击建筑物时防雷系统中雷电流的分布研究

主要讨论雷直击建筑物时雷电流在防雷系统中的分布特性，介绍利用计算机进行数值计算的方法。通过典型算例、传统的电磁暂态计算程序——EMTP的计算结果和利用清华大学高压实验室的冲击大电流发生装置，对此结构模型进行模拟试验，将3种结果进行比较，从而验证了本研究所编制的计算机程序的正确性。为进一步研究室内电磁场的暂态分析做好基础。     

Interference torque of a three-floated gyroscope with gas-lubricated bearings subject to a sudden change of the specific force

A numerical study is carried out to investigate the influence of a sudden change of the specific force on a three-floated gyroscope with a rotor supported on gas-lubricated bearings.The interference torque is calculated to evaluate the influence by modeling the transient behavior of the rotor-bearing system. In combination with dynamic equations of the rotor displacement,the Reynolds equation is solved on the surface of spiral-grooved conical bearings. It is assumed that a steady state has been obtained with a constant specific force, and then the specific force is suddenly changed and maintained constant after that. Responses of the sudden change are obtained by solving the equations. Numerical results show that the direction of the sudden change of the specific force is the main factor which influences the interference torque curve. With a sudden change along the input direction, the interference torque fluctuation has a constant frequency and a decreasing amplitude. With a sudden change along the output direction, the interference torque fluctuates in a small range. With a sudden change along the spin direction, the change of the interference torque combines a fluctuation and a gradually-changing quasi-equilibrium value. This study provides a supplement to the steady-state error model of the three-floated gyroscope.     

Measurement of Distributed Targets with the Random Signal Radar

A model of a distributed target as a collection of independent, Poisson distributed point scatterers or scattering centers in a range-velocity target space is introduced and is characterized by a deterministic function called the ?scatterer density function.? This function is the density of the point scatterers in the range-velocity space and can be estimated in a relatively straightforward manner by any radar having adequate resolution in both range and velocity and no ambiguities in the region occupied by the distributed target. The use of the random signal radar with a correlator receiver is considered here and the statistical properties of the correlator output, when the return signal is from a distributed target, are derived. It is shown that the spectral density is simply related to the scatterer density function. The technique is illustrated by an example in which the target is a tornado modeled as a cylinder with constant angular velocity. The example suggests that is a possible to remotely estimate the radar cross section per unit volume as a function of distance from the center of the tornado.     

An automated approach to calculating the maximum diameters of multiple cutters and their paths for sectional milling of centrifugal impellers on a 4?-axis CNC machine

Power generators and chemical engineering compressors include heavy and large centrifugal impellers. To produce these impellers in high-speed machining, a 4?-axis milling machine(or a 4-axis machine plus an indexing table) is often used in the industry, which is more rigid than a5-axis milling machine. Since impeller blades are designed with complex B-spline surfaces and impeller channels spaces vary significantly, it is more efficient to use multiple cutters as large as possible to cut a channel in sections and a blade surface in patches, instead of only using a small cutter to machine a whole blade and a channel. Unfortunately, no approach has been established to automatically calculate the largest diameters of cutters and their paths, which include the indexing table angles. To address this problem, an automated and optimization approach is proposed. Based on the structure of a 4?-axis machine, a geometric model for a cutter gouging/interfering the impeller is formulated, and an optimization model of the cutter diameter in terms of the indexing table angle is established at a cutter contact(CC) point on a blade surface. Then, the diameters of the tools,their orientations, and the indexing table angles are optimized, and each tool's paths are generated for machining its corresponding impeller section. As a test, an impeller is efficiently machined with these tools section by section; thus, this approach is valid. It can be directly used in the industry to improve efficiency of machining centrifugal impellers.     

直升机外挂吊运技术研究

直升机外部吊挂运送物资在国防和国民经济建设中有极为广泛的用途。本文以直8A型机和米171直升机为例，对直升机外挂吊运的飞行性能计算、全机稳定性、吊具系统的设计、飞行员和指挥员、信号员和索具员如何协调等问题进行了研究分析，为今后执行外挂吊运任务的设计和实施，提供了有价值的建议。     

受均匀内压作用的偏置孔边径向裂纹的应力强度因子的一种求解方法

本文利用一种新的混合法——光弹性实验与权函数解法相结合求解了孔壁受均匀内压作用偏置圆孔边径向裂纹的应力强度因子,该方法具有简单、经济、精度高等优点,对分析复杂应力场中圆孔边穿透裂纹问题,该方法同样适用,且优点更为突出.     

一个面向可变形模型实时有效的接触反馈框架

由于力反馈需要很高的计算速度及变形反馈需要详细的图形信息 ,本文提供一个实时有效的接触反馈框架 ,通过在粗糙三角形网格上进行局部细分来实现。当检测到接触后 ,将发生碰撞的表面细分以产生一个粒子系统。利用此粒子系统 ,用近似速度锥理论对形变进行模拟。同时 ,采用弹簧 -阻尼模型计算形变力。最后 ,对此框架进行了测试并实际应用于一个医疗规化仿真系统。     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

基于数据模型的某型民用飞机货舱区域腐蚀影响因素研究

 为研究舱内环境因素对民用飞机货舱区域腐蚀的影响,采集了停场飞机的货舱内外环境指标的数据,建立线性模型,给出了飞机货舱内外环境指标的数量关系。收集了国内几家航空公司某型民用飞机长期的结构腐蚀维修数据,计算了飞机货舱区域腐蚀频率与环境因素的灰色关联度,选取影响腐蚀的主要环境因素,提取主成分消除环境因素之间的多重共线性,建立腐蚀频率的多因素回归模型,研究了各类环境因素对飞机货舱区域腐蚀的影响规律与特点。分析结果表明:高温高湿天数与降水指标对该型飞机货舱区域腐蚀有显著的促进作用,并且不同航空公司的货舱区域腐蚀频率有显著差异,表明运营、结构检查和维护等人为因素对货舱区域腐蚀有显著影响。分析结果符合民用飞机货舱腐蚀控制的工程经验,表明研究方法是合理的。     

复杂串、并联系统的可靠性分配方法

根据串联系统中分系统相对复杂度越低,对其可靠性要求也就越高;并联系统中分系统相对重要程度越高、相对复杂程度越低,对其可靠性要求也就越高的原则,在传统的考虑重要度与复杂度可靠性分配方法基础上,提出了一种更易于设计实验及现场记录获取数据的适用于复杂串、并联系统的可靠性分配方法。基于此方法开发的软件已经应用于工程实际工作,并获得了良好的效果。     

基于PC2B格式自由尾迹方法的旋翼响应特性分析

旋翼自由尾迹模型的建模和桨叶动态响应计算的问题是直升机空气动力学领域中富有关键意义的课题。本文结合桨叶气动模型、旋翼涡尾迹模型、桨叶挥舞动力学模型、"PC2B"尾迹求解算法和旋翼配平模型,建立了一个时间精确的旋翼自由尾迹和桨叶动态气动响应的分析方法,并针对旋翼总距突增时的旋翼载荷和桨叶动态响应进行了计算和分析,得出了一些有意义的结果。     

A Study of Pilot Reaction Capability to Sound Stimulus

An experiment is described which was used to evaluate a typical pilot's ability to activate a switch in response to a sound stimulus. Regularly spaced voice countdown, irregular voice countdown, initiation of a tone, and termination of a tone were each used as the stimulus. The individual under test was given a task similar to that involved in maintaining accurate flight conditions to occupy his attention. The regular voice countdown is shown to be least accurate in defining the switching time, providing a mean delay of approximately -0.09 second (actually a stimulus anticipation) and a standard deviation of a bit more than 0.2 second. In each of the other cases, a mean delay of approximately 0.25 second and a standard deviation of approximately 0.09 second were obtained. This compares favorably with previous experimental results.