Systems design of a hybrid sail pole-sitter

This paper presents the preliminary systems design of a pole-sitter. This is a spacecraft that hovers over an Earth pole, creating a platform for full hemispheric observation of the polar regions, as well as direct-link telecommunications. To provide the necessary thrust, a hybrid propulsion system combines a solar sail with a more mature solar electric propulsion (SEP) thruster. Previous work by the authors showed that the combination of the two allows lower propellant mass fractions, at the cost of increased system complexity. This paper compares the pure SEP spacecraft with the hybrid spacecraft in terms of the launch mass necessary to deliver a certain payload for a given mission duration. A mass budget is proposed, and the conditions investigated under which the hybrid sail saves on the initial spacecraft initial mass. It is found that the hybrid spacecraft with near- to mid-term sail technology has a lower initial mass than the SEP case if the mission duration is 7 years or more, with greater benefits for longer duration missions. The hybrid spacecraft with far-term sail technology outperforms the pure SEP case even for short missions.     

Synergistic approach of asteroid exploitation and planetary protection

The asteroid and cometary impact hazard has long been recognised as an important issue requiring risk assessment and contingency planning. At the same time asteroids have also been acknowledged as possible sources of raw materials for future large-scale space engineering ventures. This paper explores possible synergies between these two apparently opposed views; planetary protection and space resource exploitation. In particular, the paper assumes a 5 tonne low-thrust spacecraft as a baseline for asteroid deflection and capture (or resource transport) missions. The system is assumed to land on the asteroid and provide a continuous thrust able to modify the orbit of the asteroid according to the mission objective. The paper analyses the capability of such a near-term system to provide both planetary protection and asteroid resources to Earth. Results show that a 5 tonne spacecraft could provide a high level of protection for modest impact hazards: airburst and local damage events (caused by 15–170 m diameter objects). At the same time, the same spacecraft could also be used to transport to bound Earth orbits significant quantities of material through judicious use of orbital dynamics and passively safe aero-capture manoeuvres or low energy ballistic capture. As will be shown, a 5 tonne low-thrust spacecraft could potentially transport between 12 and 350 times its own mass of asteroid resources by means of ballistic capture or aero-capture trajectories that pose very low dynamical pressures on the object.     

A small mission for in situ exploration of a primitive binary near-Earth asteroid

We present a concept for a challenging in situ science mission to a primitive, binary near-Earth asteroid. A sub-400-kg spacecraft would use solar electric propulsion to rendezvous with the C-class binary asteroid (175706) 1996 FG3. A campaign of remote observations of both worlds would be followed by landing on the ∼1 km diameter primary to perform in situ measurements. The total available payload mass would be around 34 kg, allowing a wide range of measurement objectives to be addressed. This mission arose during 2004 from the activities of the ad-hoc Small Bodies Group of the DLR-led Planetary Lander Initiative. Although the particular mission scenario proposed here was not studied further per se, the experience was carried over to subsequent European asteroid mission studies, including first LEONARD and now the Marco Polo near-Earth asteroid sample return proposal for ESA’s Cosmic Vision programme. This paper may thus be of interest as much for insight into the life cycle of mission proposals as for the concept itself.     

A multiple-rendezvous,sample-return mission to two near-Earth asteroids

We propose a dual-rendezvous mission, targeting near-Earth asteroids, including sample-return. The mission, Asteroid Sampling Mission (ASM), consists of two parts: (i) flyby and remote sensing of a Q-type asteroid, and (ii) sampling of a V-type asteroid. The targeted undifferentiated Q-type are found mainly in the near-Earth space, and to this date have not been the target of a space mission. We have chosen, for our sampling target, an asteroid from the basaltic class (V-type), as asteroids in this class exhibit spectral signatures that resemble those of the well-studied Howardite–Eucrite–Diogenite (HED) meteorite suite. With this mission, we expect to answer specific questions about the links between differentiated meteorites and asteroids, as well as gain further insight into the broader issues of early Solar System (SS) evolution and the formation of terrestrial planets. To achieve the mission, we designed a spacecraft with a dry mass of less than 3 tonnes that uses electric propulsion with a solar-electric power supply of 15 kW at 1 Astronomical Unit (AU). The mission includes a series of remote sensing instruments, envisages landing of the whole spacecraft on the sampling target, and employs an innovative sampling mechanism. Launch is foreseen to occur in 2018, as the designed timetable, and the mission would last about 10 years, bringing back a 150 g subsurface sample within a small re-entry capsule. This paper is a work presented at the 2008 Summer School Alpbach,“Sample return from the Moon, asteroids and comets” organized by the Aeronautics and Space Agency of the Austrian Research Promotion Agency. It is co-sponsored by ESA and the national space authorities of its Member and Co-operating States, with the support of the International Space Science Institute and Austrospace.     

The dynamics and control of the CubeSail mission: A solar sailing demonstration

The CubeSail mission is a low-cost demonstration of the UltraSail solar sailing concept (, ,  and ), using two near-identical CubeSat satellites to deploy a 260 m-long, 20 m² reflecting film. The two satellites are launched as a unit, detumbled, and separated, with the film unwinding symmetrically from motorized reels. The conformity to the CubeSat specification allows for reduction in launch costs as a secondary payload and utilization of the University of Illinois-developed spacecraft bus. The CubeSail demonstration is the first in a series of increasingly-complex missions aimed at validating several spacecraft subsystems, including attitude determination and control, the separation release unit, reel-based film deployment, as well as the dynamical behavior of the sail and on-orbit solar propulsion. The presented work describes dynamical behavior and control methods used during three main phases of the mission. The three phases include initial detumbling and stabilization using magnetic torque actuators, gravity-gradient-based deployment of the film, and steady-state film deformations in low Earth orbit in the presence of external forces of solar radiation pressure, aerodynamic drag, and gravity-gradient.     

主带小行星采样返回任务中的离子电推进应用方案

由于离子电推进的高比冲特性,采用它执行小行星探测器巡航阶段轨道机动任务时,将使探测器在同样的有效载荷下的发射重量大大减轻。针对我国规划中的主带小行星采样返回任务,调研了国外离子电推进在深空探测任务中的应用情况,在借鉴国外成功经验和任务需求分析的基础上,设计了主带小行星探测器离子电推进系统方案和应用策略,计算了在目前离子推力器寿命水平下,既定探测任务对离子电推进推力、比冲、推进剂量以及功耗需求。研究表明,目前研制的离子推力器可以满足规划中的主带小行星探测任务需求。研究成果对探测器的方案设计有参考价值。     

Mars Phobos and Deimos Survey (M-PADS) – A martian Moons orbiter and Phobos lander

We describe a Mars ‘Micro Mission’ for detailed study of the martian satellites Phobos and Deimos. The mission involves two ∼330 kg spacecraft equipped with solar electric propulsion to reach Mars orbit. The two spacecraft are stacked for launch: an orbiter for remote investigation of the moons and in situ studies of their environment in Mars orbit, and another carrying a lander for in situ measurements on the surface of Phobos (or alternatively Deimos). Phobos and Deimos remain only partially studied, and Deimos less well than Phobos. Mars has almost always been the primary mission objective, while the more dedicated Phobos project (1988–89) failed to realise its full potential. Many questions remain concerning the moons’ origins, evolution, physical nature and composition. Current missions, such as Mars Express, are extending our knowledge of Phobos in some areas but largely neglect Deimos. The objectives of M-PADS focus on: origins and evolution, interactions with Mars, volatiles and interiors, surface features, and differences. The consequent measurement requirements imply both landed and remote sensing payloads. M-PADS is expected to accommodate a 60 kg orbital payload and a 16 kg lander payload. M-PADS resulted from a BNSC-funded study carried out in 2003 to define candidate Mars Micro Mission concepts for ESA’s Aurora programme.     

Development of the High Altitude Student Platform

The High Altitude Student Platform (HASP) was originally conceived to provide student groups with access to the near-space environment for flight durations and experiment capabilities intermediate between what is possible with small sounding balloons and low Earth orbit rocket launches. HASP is designed to carry up to twelve student payloads to an altitude of about 36 km with flight durations of 15–20 h using a small zero-pressure polyethylene film balloon. This provides a flight capability that can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. Over the last two years a partnership between the NASA Balloon Program Office (BPO), Columbia Scientific Balloon Facility (CSBF), Louisiana State University (LSU), the Louisiana Board of Regents (BoR), and the Louisiana Space Consortium (LaSPACE) has led to the development, construction and, finally, the first flight of HASP with a complement of eight student payloads on September 4, 2006. Here we discuss the primary as-built HASP systems and features, the student payload interface, HASP performance during the first flight and plans for continuing HASP flights. The HASP project maintains a website at http://laspace.lsu.edu/hasp/ where flight application, interface documentation and status information can be obtained.     

CubeSail: A low cost CubeSat based solar sail demonstration mission

CubeSail is a nano-solar sail mission based on the 3U CubeSat standard, which is currently being designed and built at the Surrey Space Centre, University of Surrey. CubeSail will have a total mass of around 3 kg and will deploy a 5 × 5 m sail in low Earth orbit. The primary aim of the mission is to demonstrate the concept of solar sailing and end-of-life de-orbiting using the sail membrane as a drag-sail. The spacecraft will have a compact 3-axis stabilised attitude control system, which uses three magnetic torquers aligned with the spacecraft principle axis as well as a novel two-dimensional translation stage separating the spacecraft bus from the sail. CubeSail’s deployment mechanism consists of four novel booms and four-quadrant sail membranes. The proposed booms are made from tape-spring blades and will deploy the sail membrane from a 2U CubeSat standard structure. This paper presents a systems level overview of the CubeSat mission, focusing on the mission orbit and de-orbiting, in addition to the deployment, attitude control and the satellite bus.     

A mission concept for the low-cost large-scale exploration and characterisation of near earth objects

This paper presents the preliminary mission and science analysis of a new mission concept for the large scale, low-cost exploration of Near Earth Objects (NEOs). The concept is to enable close range observations of NEOs by performing close flybys of a series of NEOs at one of their nodal points, with pairs of small spacecraft flying in formation. The paper presents a preliminary assessment of accessible asteroids and multi-target tour trajectories from data available in the JPL small-body database.The main instruments on board each spacecraft are a camera and a LIDAR which together can be used for orbit determination, surface imaging, direct asteroid ranging and asteroid mass estimation via intersatellite ranging. The paper provides a qualitative and quantitative assessment of the measurable quantities during each flyby. In particular, the feasibility of a novel method of NEO mass estimation is assessed.     

ASTEX: An in situ exploration mission to two near-Earth asteroids

ASTEX (ASTeroid EXplorer) is a concept study of an in situ exploration mission to two Near-Earth-Asteroids (NEAs), which consists of an orbiting element and two individual lander units. The target candidates have different mineralogical compositions, i.e. one asteroid is chosen to be of “primitive’’ nature, the other to be a fragment of a differentiated asteroid. The main scientific goals of the ASTEX mission are the exploration of the physical, geological, and mineralogical nature of the NEAs. The higher level goal is the provision of information and constraints on the formation and evolution of our planetary system. The study identified realistic mission scenarios, defined the strawman payload as well as the requirements and options for the spacecraft bus including the propulsion system, the landers, the launcher, and assessed and defined the requirements for the mission’s operational ground segment.     

从日地系统L2出发借力月球飞越近地小行星

对于停留在日地系统L2的“嫦娥2号”探测器,其后续飞行方案有多个选项,例如主动撞月或重返月球轨道、返回地球轨道或再入大气、飞往地月系统L1/L2或日地系统L1、进入深空飞越近地小行星(最终,“嫦娥2号”于2012年12月13日成功地实现了对Toutatis小行星的近距离飞越)。探讨上述的飞行方案需要对飞行轨道进行初步设计,总的速度脉冲限制在100 m/s以内并且需要考虑探测器同时受到太阳、地球、月球的引力作用。本研究设计了探测器从日地系统L2出发借力月球实现Toutatis小行星飞越的飞行方案,与直接飞越方案相比,借力月球可以进一步节省探测器的燃料消耗,其等效速度脉冲设计值为58.47 m/s。     

Economic assessment of high-thrust and solar-sail propulsion for near-earth asteroid mining

Asteroid mining has the potential to greatly reduce the cost of in-space manufacturing, production of propellant for space transportation and consumables for crewed spacecraft, compared to launching the required resources from the Earth’s deep gravity well. This paper discusses the top-level mission architecture and trajectory design for these resource-return missions, comparing high-thrust trajectories with continuous low-thrust solar-sail trajectories. The paper focuses on maximizing the economic Net Present Value, which takes the time-cost of finance into account and therefore balances the returned resource mass and mission duration. The different propulsion methods are compared in terms of maximum economic return and sets of attainable target asteroids. Results for transporting resources to geostationary orbit show that the orbital parameter hyperspace of suitable target asteroids is considerably larger for solar sails, allowing for more flexibility in selecting potential target asteroids. Also, results show that the Net Present Value that can be realized is larger when employing solar sailing instead of chemical propulsion. In addition, it is demonstrated that a higher Net Present Value can be realized when transporting volatiles to the Lunar Gateway instead of geostationary orbit. The paper provides one more step towards making commercial asteroid mining an economically viable reality by integrating trajectory design, propulsion technology and economic modelling.     

Encounter trajectories for deep space mission ASTER to the triple near Earth asteroid 2001-SN263. The laser altimeter (ALR) point of view

In cooperation with Russia, the Brazilian deep space mission ASTER plans to send a small spacecraft to investigate the triple asteroid 2001-SN263. The nearest launch opportunities for this project include June 2022 and June 2025. One main exploration campaign is being planned with focus on the largest asteroid (Alpha). Among the instruments under development, a laser altimeter (named ALR) was preliminarily designed and presented in 2010–2011. Many studies to define mission and instruments requirements were performed aiming at the characterization of important issues for the successful realization of the mission. Among them, the identification of a suitable trajectory that could be followed by the ASTER spacecraft in the encounter phase, when the main campaign will take place. This paper describes the effort undertaken with focus on the laser altimeter operation. Possible encounter trajectories were modelled and simulated to identify suitable approach parameters and conditions allowing the accomplishment of the intended investigation. The simulation also involves the instrument operation, considering approach geometry, attitude, relative motion, time/date, and the dynamics of the main asteroid. From the laser altimeter point of view, keeping in mind the desired coverage results (50% minimum surface coverage of asteroid Alpha, complying with horizontal and vertical resolution requirements), results point out crucial features for the encounter trajectory, like the need for a small inclination (10^-6 degrees; with respect to the asteroid's orbit), the most favourable spacecraft positioning (between the Sun and the asteroid) and pointing condition (back to the Sun), the minimum amount of achievable surface coverage (58%, focused on central areas), and the most proper time to conduct the main campaign (January 2025). Concerning the instrument, results offer refined values for divergence angle (500 to 650 μrad, half-cone), pulse repetition frequencies (from 1/20 to 1 Hz), and consequent data generation rates. A simulation tool that can use any 3D generated trajectories as input data was created for the analyses presented here. Although created for the ALR in this mission, this simple analysis tool can be adapted to other instruments in this or other missions.     

The fundamental physics explorer: An ESA technology reference study

ESA technology reference studies are used as a process to identify key technologies and technical challenges of potential future missions not yet in the science programme. This paper reports on the study of the Fundamental Physics Explorer (FPE), a re-usable platform targeted to small missions testing fundamental laws of physics in space. The study addresses three specific areas of interest: special and general relativity tests based on atomic clocks, experiments on the Weak Equivalence Principle (WEP), and studies of Bose–Einstein condensates under microgravity conditions. Starting from preliminary science objectives and payload requirements, three reference missions in the small/medium class range are discussed, based on a re-adaptation of the LISA Pathfinder spacecraft. A 700/3600 km elliptic orbit has been selected to conduct clock tests of special and general relativity, a 700 km circular orbit to perform experiments on the Weak Equivalence Principle and to study Bose–Einstein condensates, each mission being based on a three-axis stabilised spacecraft. It was determined that adaptation of LISA Pathfinder would be required in order to meet the demands of the FPE missions. Moreover it was established that specific payload and spacecraft technology development would be required to realise such a programme.     

Imaging interplanetary CMEs at radio frequency from solar polar orbit

Coronal mass ejections (CMEs) represent a great concentration of mass and energy input into the lower corona. They have come to be recognized as the major driver of physical conditions change in the Sun–Earth system. Consequently, observations of CMEs are important for understanding and ultimately predicting space weather conditions. This paper discusses a proposed mission, the Solar Polar Orbit Radio Telescope (SPORT) mission, which will observe the propagation of interplanetary CMEs to distances of near 0.35 AU from the Sun. The orbit of SPORT is an elliptical solar polar orbit. The inclination angle between the orbit and ecliptic plane should be about 90°. The main payload on board SPORT will be an imaging radiometer working at the meter wavelength band (radio telescope), which can follow the propagation of interplanetary CMEs. The images that are obtained by the radio telescope embody the brightness temperature of the objectives. Due to the very large size required for the antenna aperture of the radio telescope, we adopt interferometric imaging technology to reduce it. Interferometric imaging technology is based on indirect spatial frequency domain measurements plus Fourier transformation. The SPORT spacecraft will also be equipped with a set of optical and in situ measurement instruments such as a EUV solar telescope, a solar wind ion instrument, an energetic particle detector, a magnetometer, a wave detector and a solar radio burst spectrometer.     

The Giotto mission to Halley''s comet

ESA's Giotto mission to Halley's comet is a fast flyby in March 1986, about four weeks after the comet's perihelion passage when it is most active. The scientific payload comprises 10 experiments with a total mass of about 60 kg: a camera for imaging the comet nucleus, three mass spectrometers for analysis of the elemental and isotopic composition of the cometary gas and dust environment, various dust impact detectors, a photopolarimeter for measurements of the coma brightness, and a set of plasma instruments for studies of the solar wind/comet interaction. In view of the high flyby velocity of 68 km/s the experiment active time is very short (only 4 hours) and all data are transmitted back to Earth in real time at a rate of 40 kbps. The Giotto spacecraft is spin-stabilised with a despun high gain parabolic dish antenna inclined at 44.3° to point at the Earth during the encounter while a specially designed dual-sheet bumper shield at the other end protects the spacecraft from being destroyed by hypervelocity dust impacts. The mission will probably end near the point of closest approach to the nucleus when the spacecraft attitude will be severely perturbed by impacting dust particles leading to a loss of the telecommunications link.     

Dynamics and control of spacecraft hovering using the geomagnetic Lorentz force

To achieve hovering, a spacecraft thrusts continuously to induce an equilibrium state at a desired position. Due to the constraints on the quantity of propellant onboard, long-time hovering around low-Earth orbits (LEO) is hardly achievable using traditional chemical propulsion. The Lorentz force, acting on an electrostatically charged spacecraft as it moves through a planetary magnetic field, provides a new propellantless method for orbital maneuvers. This paper investigates the feasibility of using the induced Lorentz force as an auxiliary means of propulsion for spacecraft hovering. Assuming that the Earth’s magnetic field is a dipole that rotates with the Earth, a dynamical model that characterizes the relative motion of Lorentz spacecraft is derived to analyze the required open-loop control acceleration for hovering. Based on this dynamical model, we first present the hovering configurations that could achieve propellantless hovering and the corresponding required specific charge of a Lorentz spacecraft. For other configurations, optimal open-loop control laws that minimize the control energy consumption are designed. Likewise, the optimal trajectories of required specific charge and control acceleration are both presented. The effect of orbital inclination on the expenditure of control energy is also analyzed. Further, we also develop a closed-loop control approach for propellantless hovering. Numerical results prove the validity of proposed control methods for hovering and show that hovering around low-Earth orbits would be achievable if the required specific charge of a Lorentz spacecraft becomes feasible in the future. Typically, hovering radially several kilometers above a target in LEO requires specific charges on the order of 0.1 C/kg.     

A sample collector for robotic sample return missions II: Radiation tests

Sample return from small solar system objects is playing an increasingly important part in solar system exploration. Critical to such missions is a robust, simple, and economic sample collector. We have developed a collector such as this for near-Earth asteroid sample return missions that we have termed the Touch-and-Go Impregnable Pad (TGIP). The collector utilizes a silicone substrate that is pushed into the dust and gravel surface layer of the asteroid. As part of a systematic evaluation of the TGIP, we have investigated the resilience of this substrate to ionizing radiations. Several miniature versions of the collector, containing typically ∼3 g of the collection substrate, were exposed to 0.564 MeV beta particles from a ⁹⁰Sr source and a 6 MeV electron beam in a linear accelerator to simulate the wide range of energies of solar and galactic ionizing radiation. Various radiation levels up to eight times greater than expected on a six-year asteroid mission (in the case of beta radiation) and 50 times greater than expected (in the case of the 6 MeV electron radiation) were administered to the substrate. After irradiation, the efficiency of the substrate in collecting samples of mock regolith was compared with that of collectors that had not been irradiated. No difference beyond experimental uncertainty was observed and we suggest that the operational TGIP will not be affected adversely by radiation doses expected during a typical six-year inner solar system mission.