Generating precise and homogeneous orbits for Jason-1 and Jason-2

Driven by the GMES (Global Monitoring for Environment and Security) and GGOS (Global Geodetic Observing System) initiatives the user community has a strong demand for high-quality altimetry products. In order to derive such high-quality altimetry products, precise orbits for the altimetry satellites are a necessity. With the launch of the TOPEX/Poseidon mission in 1992 a still on-going time series of high-accuracy altimetry measurements of ocean topography started, continued by the altimetry missions Jason-1 in 2001 and Jason-2/OSTM in 2008. This paper contributes to the on-going orbit reprocessing carried out by several groups and presents the efforts of the Navigation Support Office at ESA/ESOC using its NAPEOS software for the generation of precise and homogeneous orbits referring to the same reference frame for the altimetry satellites Jason-1 and Jason-2. Data of all three tracking instruments on-board the satellites (beside the altimeter), i.e. GPS, DORIS, and SLR measurements, were used in a combined data analysis. About 7 years of Jason-1 data and more than 1 year of Jason-2 data were processed. Our processing strategy is close to the GDR-C standards. However, we estimated slightly different scaling factors for the solar radiation pressure model of 0.96 and 0.98 for Jason-1 and Jason-2, respectively. We used 30 s sampled GPS data and introduced 30 s satellite clocks stemming from ESOC’s reprocessing of the combined GPS/GLONASS IGS solution. We present the orbit determination results, focusing on the benefits of adding GPS data to the solution. The fully combined solution was found to give the best orbit results. We reach a post-fit RMS of the GPS phase observation residuals of 6 mm for Jason-1 and 7 mm for Jason-2. The DORIS post-fit residuals clearly benefit from using GPS data in addition, as the DORIS data editing improves. The DORIS observation RMS for the fully combined solution is with 3.5 mm and 3.4 mm, respectively, 0.3 mm better than for the DORIS-SLR solution. Our orbit solution agrees well with external solutions from other analysis centers, as CNES, LCA, and JPL. The orbit differences between our fully combined orbits and the CNES GDR-C orbits are of about 0.8 cm for Jason-1 and at 0.9 cm for Jason-2 in the radial direction. In the cross-track component we observe a clear improvement when adding GPS data to the POD process. The 3D-RMS of the orbit differences reveals a good orbit consistency at 2.7 cm and 2.9 cm for Jason-1 and Jason-2. Our resulting orbit series for both Jason satellites refer to the ITRF2005 reference frame and are provided in sp3 file format on our ftp server.     

Coastal sea level changes in Europe from GPS,tide gauge,satellite altimetry and GRACE, 1993–2011

Sea level changes are threatening the human living environments, particularly along the European Coasts with highly dense population. In this paper, coastal sea level changes in western and southern Europe are investigated for the period 1993–2011 using Global Positioning System (GPS), Tide Gauge (TG), Satellite Altimetry (SA), Gravity Recovery and Climate Experiment (GRACE) and geophysical models. The mean secular trend is 2.26 ± 0.52 mm/y from satellite altimetry, 2.43 ± 0.61 mm/y from TG+GPS and 1.99 ± 0.67 mm/y from GRACE mass plus steric components, which have a remarkably good agreement. For the seasonal variations, annual amplitudes of satellite altimetry and TG+GPS results are almost similar, while GRACE Mass+Steric results are a little smaller. The annual phases agree remarkably well for three independent techniques. The annual cycle is mainly driven by the steric contributions, while the annual phases of non-steric (mass component) sea level changes are almost a half year later than the steric sea level changes.     

Refining DORIS atmospheric drag estimation in preparation of ITRF2008

In preparation of ITRF2008, all geodetic technique services (VLBI, SLR, GPS and DORIS) are generating new solutions based on combination of individual analysis centers solutions. These data reprocessing are based on a selection of models, parameterization and estimation strategy unique to each analysis center and to each technique. While a good agreement can be found for models between groups, thanks to the existence of the IERS conventions, a great diversity still exist for parameter estimation, allowing possible future improvements in this direction. The goal of this study is to focus on the atmospheric drag estimation used to generate the new DORIS/IGN ignwd08 time series prepared for ITRF2008. We develop here a method to inter-compare different processing strategies. In a first step, by analyzing single-satellite solutions for a few weeks of data but for a large number of possible analysis strategies, we demonstrate that estimating drag coefficient more frequently (typically every 1–2 h instead of previously every 4–8 h) for the lowest DORIS satellites (SPOTs and Envisat) provides better geodetic results for station coordinates and polar motion. This new processing strategy also solved earlier problem found when processing DORIS data during intense geomagnetic events, such as geomagnetic storms. Differences between drag estimation strategies can mostly be found during these few specific periods of extreme geomagnetic activity (few days per year). In such a case, when drag coefficient is only estimated every 6 h or less often for single-satellite solution, a significant degradation in station coordinate accuracy can be observed (120 mm vs. 20 mm) and significant biases arose in polar motion estimation (5 mas vs. 0.3 mas). In a second step, we reprocessed a full year of DORIS data (2003) in a standard multi-satellite mode. We were able to provide statistics on a more reliable data set and to strengthen these conclusions. Our proposed DORIS analysis is easy to implement in all software packages and is now already used by several analysis centers of the International DORIS Service (IDS) when submitting reprocessed solutions for ITRF2008.     

DORIS processing at the European Space Operations Centre

This paper gives an overview of the DORIS related activities at the Navigation Support Office of the European Space Operations Centre. The DORIS activities were started in 2002 because of the launch of the Envisat satellite where ESOC is responsible for the validation of the Envisat Precise Orbits and a brief overview of the key Envisat activities at ESOC is given. Typical orbit comparison RMS values between the CNES POE (GDR-C) and the ESOC POD solution is 6.5, 18.8 and 23.1 mm in radial-, along- and cross-track direction. In the framework of the generation of the ITRF2008 ESOC participated in the reprocessing of all three space geodetic techniques; DORIS, SLR, and GPS. Here the main results of our DORIS reprocessing, in the framework of the International DORIS Service (IDS), are given. The WRMS of the weekly ESOC solution (esawd03) for the 2004–2009 period compared to the IDS-1 combined solution is of the order of 12 mm. Based on the long time series of homogeneously processed data a closer look is taken at the estimated solar radiation pressure parameters of the different satellites used in this DORIS analysis. The main aim being the stabilization of the Z-component of the geocentre estimates. We conclude that the ESOC participation to the IDS ITRF2008 contribution has been beneficial for both ESOC and the IDS. ESOC has profited significantly from the very open and direct communications and comparisons that took place within the IDS during the reprocessing campaign.     

An inter-comparison of zenith tropospheric delays derived from DORIS and GPS data

Doppler Orbitography Radiopositioning Integrated by Satellite (DORIS) and Global Positioning System (GPS) techniques are similarly affected by propagation delays in the neutral atmosphere (troposphere) and hence make use of similar data processing strategies for reducing this effect. We compare Zenith Tropospheric Delays (ZTDs) estimated from 52 DORIS and GPS station pairs co-located at 35 sites over the 2005–2008 period. We find an overall systematic negative mean bias of −4 mm and a median bias of −2 mm, with a large site-to-site scatter and especially stronger biases over South America, potentially linked to remaining problems related to the South Atlantic Anomaly (SAA) in the current DORIS data processing. The standard deviation of ZTD differences is in the range 4–12 mm over the globe (8 mm on average), with larger values located in the southern hemisphere. The spatial variability of differences is consistent with previous work but remains largely unexplained. DORIS is shown to be much less sensitive to instrumental changes than GPS (only the switch from Alcatel to Starec antenna at Toulouse is detected as an offset of −4 mm in the ZTD time series). On the opposite, discontinuities and spurious annual signals are found in the GPS ZTD solutions. A discontinuity of +5 mm is found on 5 November 2006, linked to the switch from relative to absolute GPS antenna models used in the data processing. The use of modified GPS antennas (e.g. at GODE) or improved antenna models is shown to reduce the spurious annual signal (e.g. from 5 mm to 2 mm at METS). Overall, the agreement between both techniques is good, though DORIS shows a significantly larger random scatter. The high stability and good spatial and temporal coverage make DORIS a potential candidate technique for meteorology and climate studies as long as reasonable time averaging can be applied (e.g. differences are reduced from 8.6 to 2.4 mm with 5-day averages) and no real-time application is considered. This technique could be considered as a potential contributor to Global Geodetic Observing System (GGOS) for climatology.     

The International DORIS Service (IDS): Toward maturity

DORIS is one of the four space-geodetic techniques participating in the Global Geodetic Observing System (GGOS), particularly to maintain and disseminate the Terrestrial Reference Frame as determined by International Earth rotation and Reference frame Service (IERS). A few years ago, under the umbrella of the International Association of Geodesy, a DORIS International Service (IDS) was created in order to foster international cooperation and to provide new scientific products. This paper addresses the organizational aspects of the IDS and presents some recent DORIS scientific results. It is for the first time that, in preparation of the ITRF2008, seven Analysis Centers (AC’s) contributed to derive long-term time series of DORIS stations positions. These solutions were then combined into a homogeneous time series IDS-2 for which a precision of less than 10 mm was obtained. Orbit comparisons between the various AC’s showed an excellent agreement in the radial component, both for the SPOT satellites (e.g. 0.5–2.1 cm RMS for SPOT-2) and Envisat (0.9–2.1 cm RMS), using different software packages, models, corrections and analysis strategies. There is now a wide international participation within IDS that should lead to future improvements in DORIS analysis strategies and DORIS-derived geodetic products.     

Towards development of a consistent orbit series for TOPEX,Jason-1, and Jason-2

The TOPEX/Poseidon, Jason-1 and Jason-2 set of altimeter data now provide a time series of synoptic observations of the ocean that span nearly 17 years from the launch of TOPEX in 1992. The analysis of the altimeter data including the use of altimetry to monitor the global change in mean sea level requires a stable, accurate, and consistent orbit reference over the entire time span. In this paper, we describe the recomputation of a time series of orbits that rely on a consistent set of reference frames and geophysical models. The recomputed orbits adhere to the IERS 2003 standards for ocean and earth tides, use updates to the ITRF2005 reference frame for both the SLR and DORIS stations, apply GRACE-derived models for modeling of the static and time-variable gravity, implement the University College London (UCL) radiation pressure model for Jason-1, use improved troposphere modeling for the DORIS data, and apply the GOT4.7 ocean tide model for both dynamical ocean tide modeling and for ocean loading. The new TOPEX orbits have a mean SLR fit of 1.79 cm compared to 2.21 cm for the MGDR-B orbits. These new TOPEX orbits agree radially with independent SLR/crossover orbits at 0.70 cm RMS, and the orbit accuracy is estimated at 1.5–2.0 cm RMS over the entire TOPEX time series. The recomputed Jason-1 orbits agree radially with the Jason-1 GDR-C orbits at 1.08 cm RMS. The GSFC SLR/DORIS dynamic and reduced-dynamic orbits for Jason-2 agree radially with independent orbits from the CNES and JPL at 0.70–1.06 cm RMS. Applying these new orbits, and using the latest altimeter corrections for TOPEX, Jason-1, and Jason-2 from September 1992 to May 2009, we find a global rate in mean sea level of 3.0 ± 0.4 mm/yr.     

DORIS geodesy: A dynamic determination of geocentre location

Geoscience Australia contributed a multi-satellite, multi-year weekly time series to the International DORIS Service combined submission for the construction of International Terrestrial Reference Frame 2008 (ITRF2008). This contributing solution was extended to a study of the capability of DORIS to dynamically estimate the variation in the geocentre location. Two solutions, comprising different constraint configurations of the tracking network, were undertaken. The respective DORIS satellite orbit solutions (SPOT-2, SPOT-4, SPOT-5 and Envisat) were verified and validated by comparison with those produced at the Goddard Space Flight Center (GSFC), DORIS Analysis Centre, for computational consistency and standards. In addition, in the case of Envisat, the trajectories from the GA determined SLR and DORIS orbits were compared. The results for weekly dynamic geocentre estimates from the two constraint configurations were benchmarked against the geometric geocentre estimates from the IDS-2 combined solution. This established that DORIS is capable of determining the dynamic geocentre variation by estimating the degree one spherical harmonic coefficients of the Earth’s gravity potential. It was established that constrained configurations produced similar results for the geocentre location and consequently similar annual amplitudes. For the minimally constrained configuration Greenbelt–Kitab, the mean of the uncertainties of the geocentre location were 2.3, 2.3 and 7.6 mm and RMS of the mean uncertainties were 1.9, 1.2 and 3.5 mm for the X, Y and Z components, respectively. For GA_IDS-2_Datum constrained configuration, the mean of the uncertainties of the geocentre location were 1.7, 1.7 and 6.2 mm and RMS of the mean uncertainties were 0.9, 0.7 and 2.9 mm for the X, Y and Z components, respectively. The mean of the differences of the two DORIS dynamic geocentre solutions with respect to the IDS-2 combination were 1.6, 4.0 and 5.1 mm with an RMS of the mean 21.2, 14.0 and 31.5 mm for the Greenbelt–Kitab configuration and 4.1, 3.9 and 4.3 mm with an RMS 8.1, 9.0 and 28.6 mm for the GA_IDS-2_Datum constraint configuration. The annual amplitudes for each component were estimated to be 5.3, 10.8 and 11.0 mm for the Greenbelt–Kitab configuration and 5.3, 9.3 and 9.4 mm for the GA_IDS-2_Datum constraint configuration. The two DORIS determined dynamic geocentre solutions were compared to the SLR determined dynamic solution (which was determined from the same process of the GA contribution to the ITRF2008 ILRS combination) gave mean differences of 3.3, −4.7 and 2.5 mm with an RMS of 20.7, 17.5 and 28.0 mm for the X, Y and Z components, respectively for the Greenbelt–Kitab configuration and 1.1, −5.4 and 4.4 mm with an RMS of 9.7, 13.3 and 24.9 mm for the GA_IDS-2_Datum configuration. The larger variability is reflected in the respective amplitudes. As a comparison, the annual amplitudes of the SLR determined dynamic geocentre are 0.9, 1.0 and 6.8 mm in the X, Y and Z components. The results from this study indicate that there is potential to achieve precise dynamically determined geocentre from DORIS.     

Interseismic slip rate of the Garze–Yushu fault belt in the Tibetan Plateau from C-band InSAR observations between 2003 and 2010

InSAR time series techniques can provide high-spatial resolution deformation fields across an active fault belt, even for zones with heavy vegetation coverage. An interseismic deformation map across the Garze–Yushu fault belt in the Tibetan Plateau, ∼300 km by ∼100 km, is derived from C-band Envisat/ASAR imagery collected between 2003 and 2010. Unlike previous research, we obtain a lookup figure which relates the slip rate with the fault locking depth, the dip angle and the rake angle. The estimated slip rate changes significantly with the locking depth and the rake angle, but relatively little with the dip angle. When considering the focal mechanism solutions of historical earthquake along the Garze–Yushu fault, the interseismic slip rate of the Garze–Yushu fault is close to a value of 6.4 mm/yr, which is between the highest (18.2 mm/yr) and the lowest (3.1 mm/yr) slip rate from GPS estimations, but slightly less than the minimum value (∼ 7 mm/yr) from the geological estimations. The earthquake recurrence interval on the Yushu part of Garze–Yushu fault equals 272 yr, and the April 14, 2010 Mw 6.9 earthquake has not completely released the accumulated strain energy between 1738 and 2010.     

Studies of the geocenter motion using 16-years DORIS data

An accuracy of geocenter motion estimation is strongly dependent on the geodetic network size and stations distribution over the Earth’s surface. From this point of view DORIS system has an advantage, as its ground network of beacons consists of more than 50 sites, equally distributed over the Earth’s surface. Aiming to study variations of the geocenter movements, the results of DORIS data analysis for the time span 1993.0–2009.0 (inawd06.snx series), performed at the Analysis Centre of the Institute of astronomy of the Russian Academy of Sciences, have been used. DORIS data processing was made with GIPSY/OASIS II software, developed by Jet Propulsion Laboratory and modified for DORIS data processing by Institute Géographique National. Standard deviations of stations coordinates are estimated at the level 0.5–4.0 cm (internal consistency), depending on the number of satellites used in the solution. RMS of estimated components of the DORIS satellites orbits, compared with the solutions of other IDS analysis centres, do not exceed 1–2 cm. Weekly solutions for coordinates have been transformed from free network solutions (inawd06.snx series) to a well defined terrestrial reference frame ITRF2005 with the use of seven parameters of Helmert transformation, which were examined with a view to study variations of the geocenter movements (ina05wd01.geoc time series). In order to estimate linear trend, amplitudes, periods and phases of geocenter variation a method of linear regression was applied. The evaluated amplitudes of annual variations are of the order of 5–7 mm for X and Y components and 27–29 mm for Z component. Semi-annual amplitudes are also noticeable in all components (1–34 mm for X, Y and Z components). Secular trends in the DORIS geocenter coordinates are: −1.2, −0.1 and −0.3 mm/year for X, Y and Z directions respectively.     

GSFC DORIS contribution to ITRF2008

The NASA GSFC DORIS analysis center has provided weekly DORIS solutions from November 1992 to January 2009 (839 SINEX files) of station positions and Earth Orientation Parameters for inclusion in the DORIS contribution to ITRF2008. The NASA GSFC GEODYN orbit determination software was used to process the orbits and produce the normal equations. The weekly SINEX gscwd10 submissions included DORIS data from Envisat, TOPEX/Poseidon, SPOT-2, SPOT-3, SPOT-4, SPOT-5. The orbits were mostly seven days in length (except for weeks with data gaps or maneuvers). The processing used the GRACE-derived EIGEN-GL04S1 gravity model, updated modeling for time-variable gravity, the GOT4.7 ocean tide model and tuned satellite-specific macromodels for SPOT-2, SPOT-3, SPOT-4, SPOT-5 and TOPEX/Poseidon. The University College London (UCL) radiation pressure model for Envisat improves nonconservative force modeling for this satellite, reducing the median residual empirical daily along-track accelerations from 3.75 × 10⁻⁹ m/s² with the a priori macromodel to 0.99 × 10⁻⁹ m/s² with the UCL model. For the SPOT and Envisat DORIS satellite orbits from 2003 to 2008, we obtain average RMS overlaps of 0.8–0.9 cm in the radial direction, 2.1–3.4 cm cross-track, and 1.7–2.3 cm along-track. The RMS orbit differences between Envisat DORIS-only and SLR & DORIS orbits are 1.1 cm radially, 6.4 cm along-track and 3.7 cm cross-track and are characterized by systematic along-track mean offsets due to the Envisat DORIS system time bias of ±5–10 μs. We obtain a good agreement between the geometrically-determined geocenter parameters and geocenter parameters determined dynamically from analysis of the degree one terms of the geopotential. The intrinsic RMS weekly position repeatability with respect to the IDS-3 combination ranges from 2.5 to 3.0 cm in 1993–1994 to 1.5 cm in 2007–2008.     

IDS contribution to ITRF2008

For the first time, the International DORIS Service (IDS) has produced a technique level combination based on the contributions of seven analysis centers (ACs), including the European Space Operations Center (ESOC), Geodetic Observatory Pecny (GOP), Geoscience Australia (GAU), the NASA Goddard Space Flight Center (GSFC), the Institut Géographique National (IGN), the Institute of Astronomy, Russian Academy of Sciences (INASAN, named as INA), and CNES/CLS (named as LCA). The ACs used five different software packages to process the DORIS data from 1992 to 2008, including NAPEOS (ESA), Bernese (GOP), GEODYN (GAU, GSC), GIPSY/OASIS (INA), and GINS (LCA). The data from seven DORIS satellites, TOPEX/Poseidon, SPOT-2, SPOT-3, SPOT-4, SPOT-5, Envisat and Jason-1 were processed and all the analysis centers produced weekly SINEX files in either variance–covariance or normal equation format. The processing by the analysis centers used the latest GRACE-derived gravity models, forward modelling of atmospheric gravity, updates to the radiation pressure modelling to improve the DORIS geocenter solutions, denser parameterization of empirically determined drag coefficients to improve station and EOP solutions, especially near the solar maximum in 2001–2002, updated troposphere mapping functions, and an ITRF2005-derived station set for orbit determination, DPOD2005. The CATREF software was used to process the weekly AC solutions, and produce three iterations of an IDS global weekly combination. Between the development of the initial solution IDS-1, and the final solution, IDS-3, the ACs improved their analysis strategies and submitted updated solutions to eliminate troposphere-derived biases in the solution scale, to reduce drag-related degradations in station positioning, and to refine the estimation strategy to improve the combination geocenter solution. An analysis of the frequency content of the individual AC geocenter and scale solutions was used as the basis to define the scale and geocenter of the IDS-3 combination. The final IDS-3 combination has an internal position consistency (WRMS) that is 15 to 20 mm before 2002 and 8 to 10 mm after 2002, when 4 or 5 satellites contribute to the weekly solutions. The final IDS-3 combination includes solutions for 130 DORIS stations on 67 different sites of which 35 have occupations over 16 years (1993.0–2009.0). The EOPs from the IDS-3 combination were compared with the IERS 05 C04 time series and the RMS agreement was 0.24 mas and 0.35 mas for the X and Y components of polar motion. The comparison to ITRF2005 in station position shows an agreement of 6 to 8 mm RMS in horizontal and 10.3 mm in height. The RMS comparison to ITRF2005 in station velocity is at 1.8 mm/year on the East component, to 1.2 mm/year in North component and 1.6 mm/year in height.     

Improving DORIS geocenter time series using an empirical rescaling of solar radiation pressure models

Even if Satellite Laser Ranging (SLR) remains the fundamental technique for geocenter monitoring, DORIS can also determine this geophysical parameter. Gobinddass et al. (2009) found that part of the systematic errors at 118 days and 1 year can be significantly reduced by rescaling the current solar radiation pressure models using satellite-dependent empirical models. Here we extend this study to all DORIS satellites and propose a complete set of empirical solar radiation parameter coefficients. A specific problem related to SPOT-5 solar panel realignment is also detected and explained. New DORIS geocenter solutions now show a much better agreement in amplitude with independent SLR solutions and with recent geophysical models. Finally, the impact of this refined DORIS data strategy is discussed in terms of Z-geocenter monitoring as well as for other geodetic products (altitude of high latitude station such as Thule in Greenland) and Precise Orbit Determination. After reprocessing the full 1993.0-2008.0 DORIS data set, we confirm that the proposed strategy allows a significant reduction of systematic errors at periods of 118 days and 1 year (up to 20 mm), especially for the most recent data after 2002.5, when more DORIS satellites are available for geodetic purposes.     

Status of the T2L2/Jason2 Experiment

The T2L2 (Time Transfer by Laser Link) project, developed by CNES and OCA will permit the synchronization of remote ultra stable clocks and the determination of their performances over intercontinental distances. The principle of the experiment derives from Satellite Laser Ranging (SLR) technology with dedicated space equipment. T2L2 was accepted in 2005 to be on board the Jason2 altimetry satellite. The payload consists of both event timer and photo detection modules. The system uses the ultra-stable quartz oscillator of DORIS as on-board reference clock on one hand, and the Laser Reflector Array, making T2L2 a real two-way time transfer system on the other hand. The expected time stability of the T2L2 instrument (detection and timing), referenced by the DORIS oscillator and including all internal error sources should be at the level of 10–12 ps at 1 s and <1 ps at 1000 s. The metrological specifications of T2L2 should permit to maintain a precision of 1 to a few ps when measuring the phase of a clock during around 1000 seconds.     

Effects of physical correlations on long-distance GPS positioning and zenith tropospheric delay estimates

The global positioning system (GPS) has become an essential tool for the high precision navigation and positioning. The quality of GPS positioning results mainly depends on the model’s formulations regarding GPS observations, including both a functional model, which describes the mathematical relationships between the GPS measurements and unknown parameters, and a stochastic model, which reflects the physical properties of the measurements. Over the past two decades, the functional models for GPS measurements have been investigated in considerable detail. However, the stochastic models of GPS observation data are simplified, assuming that all the GPS measurements have the same variance and are statistically independent. Such assumptions are unrealistic. Although a few studies of GPS stochastic models were performed, they are restricted to short baselines and short time session lengths. In this paper, the stochastic modeling for GPS long-baseline and zenith tropospheric delay (ZTD) estimates with a 24-h session is investigated using the residual-based and standard stochastic models. Results show that using the different stochastic modelling methods, the total differences can reach as much as 3–6 mm in the baseline component, especially in the height component, and 10 mm in the ZTD estimation. Any misspecification in the stochastic models will result in unreliable GPS baseline and ZTD estimations. Using the residual-based stochastic model, not only the precision of GPS baseline and ZTD estimation is obviously improved, but also the baseline and ZTD estimations are closer to the reference value.     

Using altimetry and seafloor pressure data to estimate vertical deformation offshore: Vanuatu case study

Measuring ground deformation underwater is essential for understanding Earth processes at many scales. One important example is subduction zones, which can generate devastating earthquakes and tsunamis, and where the most important deformation signal related to plate locking is usually offshore. We present an improved method for making offshore vertical deformation measurements, that involve combining tide gauge and altimetry data. We present data from two offshore sites located on either side of the plate interface at the New Hebrides subduction zone, where the Australian plate subducts beneath the North Fiji basin. These two sites have been equipped with pressure gauges since 1999, to extend an on-land GPS network across the plate interface. The pressure series measured at both sites show that Wusi Bank, located on the over-riding plate, subsides by 11 ± 4 mm/yr with respect to Sabine Bank, which is located on the down-going plate. By combining water depths derived from the on-bottom pressure data with sea surface heights derived from altimetry data, we determine variations of seafloor heights in a global reference frame. Using altimetry data from TOPEX/Poseidon, Jason-1, Jason-2 and Envisat missions, we find that the vertical motion at Sabine Bank is close to zero and that Wusi Bank subsides by at least 3 mm/yr and probably at most 11 mm/yr.     

Altimetry,bathymetry and geoid variations at the Gavdos permanent Cal/Val facility

The aim of this work has been to examine the relationship of steep bathymetry in the coastal areas around the permanent Cal/Val facility of Gavdos, and their influence on the produced calibration values for the Jason-2 satellite altimeter. The paper describes how changes in seafloor topography (from 200 to 3500 m depth over a distance of 10 km) are reflected on the determined altimeter parameters using different reference surfaces for satellite calibration. Finally, it describes the relation between these parameter trends and the region’s local characteristics.     

The Western Crete geodetic infrastructure: Long-range power-law correlations in GPS time series using Detrended Fluctuation Analysis

The Global Positioning System makes it possible, nowadays, to measure crustal displacements with unprecedented accuracy. These measurements can improve our understanding of the spatio-temporal evolution of motion along tectonic plate boundaries, as well as deepen our comprehension for the nature of earthquake fault behavior and earthquake cycle. The Hellenic subduction zone and the earthquake-prone Crete, with large crustal motions of 3–4 cm/yr, may provide such a natural laboratory for this type of investigation. In this work, we examine the statistical structure and behavior of time series, as produced by permanent GPS sites, established on the islands of Crete and Gavdos.     

The contribution of local gravimetric geoid models to the calibration of satellite altimetry data and an outlook of the latest GOCE GGM performance in Gavdos

The use of geoid heights has been one of the available methodologies utilized for the independent calibration/validation of altimeters on-board satellites. This methodology has been employed for long in the Gavdos dedicated cal/val facility (Crete, Greece), where calibration results for the Jason satellites have been estimated, both for ascending and descending passes. The present work gives a detailed overview of the methodology followed in order to estimate a high-resolution and accuracy gravimetric geoid model for the wider Gavdos area, in support of the on-going calibration work. To estimate the geoid model, the well-known remove-compute-restore method is used while residual geoid heights are estimated through least-squares collocation so that associated errors are determined as well. It is found that the estimated formal geoid errors from LSC along passes 018 and 109 of Jason satellites, used for the bias estimation, range between ±0.8–1.6 cm. The so-derived geoid heights are employed in the determination of the Jason-2 altimeter bias for all available cycles (cycles 1-114, spanning the period from July 2008 to August 2011) together with the RioMed DOT model. From the results acquired the Jason-2 bias has been estimated to be +196.1 ± 3.2 mm for pass 109 and +161.9 ± 5.1 mm for pass 018. Within the same frame, the GOCE/GRACE-based geopotential model GOCO02s has been used to estimate the mean dynamic ocean topography and the steady-state circulation in the area around Gavdos. The so-derived DOT model was used to estimate the Jason-2 bias in an effort to evaluate the performance of satellite-only geoid models and investigate whether their spatial resolution and accuracy provides some improvement w.r.t. traditional local gravimetric geoids. From the results acquired with geoid heights from GOCO02s, the estimated Jason-2 bias deviates significantly from that of the local gravimetric model, which can be attributed to a possible mean offset and the low resolution of GOCE-based GGMs. On the other hand, when the newly estimated GOCE-based DOT was employed with geoid heights from the local gravimetric geoid model, the Jason-2 bias has been estimated to be +185.1 ± 3.2 mm for pass 109 and +130.2 ± 5.1 mm for pass 018.