共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
为减少光电二极管与信号放大电路噪声对微弱光信号检测系统灵敏度的影响,提高检测精度.给出了微弱光信号检测电路噪声模型,并分析了灵敏度与带宽的关系,藉此能得到最佳的灵敏度和带宽组合.经仿真和实验表明该模拟有效,由此搭建的实验平台能测量nW级光功率. 相似文献
4.
通过对两种巴特沃兹有源滤波器设计方案的灵敏度分析,仿真了电路元件参数灵敏度随 Q 因数的变化规律,从而介绍了一种利用灵敏度分析比较网络设计方案优劣的方法。 相似文献
5.
面向加工表面粗糙度的钛合金高速铣削工艺参数区间敏感性及优选 总被引:1,自引:0,他引:1
钛合金高速铣削以高效率、高质量的优点广泛应用于航空航天行业.针对高速铣削中表面粗糙度的工艺控制,提出了基于表面粗糙度经验模型的工艺参数灵敏度和相对灵敏度概念.通过高速端面铣削正交试验,建立了面向表面粗糙度的工艺参数灵敏度和相对灵敏度数学模型,研究了工艺参数区间敏感性分析方法,给出了工艺参数稳定域和非稳定域的划分原则和方法.结合正交试验法中的极差分析方法获得了不同切削工艺参数对表面粗糙度的影响曲线,提出了工艺参数区间的优选方法.研究结果表明:TC11钛合金高速铣削时,表面粗糙度对铣削速度的变化最为敏感,对每齿进给量变化敏感次之,对铣削宽度和铣削深度的变化不敏感;铣削速度优选在314~377 m/min范围,每齿进给量优选在0.03~0.05 mm/z范围,可控制表面粗糙度在0.6 μm以内.为优化钛合金材料高速铣削工艺以及进行表面粗糙度控制研究提供理论方法和试验依据. 相似文献
6.
基于喇曼散射的分布式光纤测温系统光接收机灵敏度的分析 总被引:2,自引:0,他引:2
在分布式光纤测温系统中,携有温度信息的喇曼散射光是极其微弱的,只有 n W量级,而温度变化引起的喇曼散射光的变化更加微弱。在对光接收机噪声分析的基础上,给出了该类应用条件下光接收机信噪比。指出了低信噪比下,AD的量化误差将随累加次数的增加而减小,同时 AD的有效位数将增加,给出了低信噪比下 AD有效位数的分析方法,并通过 MATLAB进行了验证,在此基础上,分析了光接收机的灵敏度,由此可以直接计算分布式光纤测温系统的测温精度。 相似文献
7.
通过分析导弹控制系统及引信系统,研究了影响导弹控制系统及引信灵敏度的主要因素,并建立了灵敏度模型,分析了灵敏度对导弹主要性能的影响. 相似文献
8.
9.
传统的可靠性灵敏度指标只考虑了随机不确定性,当结构中还存在认知不确定性时,该指标难以反映出基本变量中认知不确定性对结构可靠性评估结果的影响程度.针对这一问题,引入概率包络来表达结构中的随机不确定性和认知不确定性,在此基础上建立了可靠性灵敏度分析的新指标——认知灵敏度系数,给出了其定义和代表的意义,并基于证据理论提出了认知灵敏度系数的计算方法.算例分析表明,认知灵敏度系数可以反映出基本变量中认知不确定性对结构可靠性评估结果的不确定性的影响程度,从而为有针对性地提高可靠性评估结果的准确性提供依据.另外,基于证据理论的认知灵敏度系数的计算方法适用于极限状态函数为单调、非单调的结构,以及变量服从正态、非正态的结构,具有普适性. 相似文献
10.
飞行器多学科设计优化中的灵敏度分析方法研究 总被引:8,自引:0,他引:8
近年来,在飞行器设计领域,多学科设计优化(MDO)方法得到了高度重视。灵敏度分析技术作为MDO的关键技术之一,被认为是处理飞行器MDO研究中四个复杂性问题的有力工具。本文对适用于飞行器MDO的灵敏度分析方法进行了系统研究。首先介绍了多种学科灵敏度分析方法,阐述了各种方法的原理,比较了各种方法的优缺点。在此基础上,进一步探讨了几种常用的系统灵敏度分析方法。最后,总结了各种灵敏度分析方法在飞行器MDO中应用的原则,并对发展适用性更广的广义灵敏度分析方法提出了建议。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
14.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
15.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
16.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
19.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献