共查询到19条相似文献,搜索用时 786 毫秒
1.
公司外贸产品法国SNECMA涡轮盘试制过程中出现榫槽表面拉削波纹,通过工艺分析找出了产生波纹的原因,并有针对性地改进了工艺及夹具,消除了榫槽表面拉削波纹,使涡轮盘表面质量达到了技术要求。 相似文献
2.
由于拉刀在拉削过程中,切屑不可能从拉刀的齿间槽排出,而是要全部容纳在齿槽中,随着拉刀移动,将拉屑带出已加工表面,因此采用偏置前角拉削,有效提高拉刀强度,解决该特型榫槽拉屑排除问题,对容屑槽的设计显得格外重要。 相似文献
3.
4.
针对现代高性能、高精度涡轮盘榫槽的加工需要,在拉刀设计上改变了传统的设计方法,采用先进的、科学的拉削方式,取得了成熟的经验,进一步发展了拉刀设计技术。本文从拉削原理入手,总结出现代涡轮盘枞树形榫槽拉刀的设计方法,可供设计人员借鉴、参考。 相似文献
5.
6.
对机匣和环形件T型槽的主要结构特点、工艺难点、成组加工技术、数控加工技术和特窄T型槽加工做了比较详细的介绍,积累了丰富的加工经验。 相似文献
7.
通过工艺试验,确定了在拉深坯料上,预制毛孔毛槽的办法,仅用一套拉深模就完成了薄料宽凸缘筒形带孔槽零件的拉深。 相似文献
8.
对马鞍形蒙皮零件进行了工艺分析,并根据数控蒙皮拉形机适用性广和加工能力强的特点,突破传统的蒙皮拉形工艺思路,首次将马鞍形蒙皮的凹模作为拉形模具,采用纵向拉形的方法,顺利地完成了某型机关键零件——进气道马鞍形蒙皮的试制任务。 相似文献
9.
10.
11.
丛伟 《沈阳航空工业学院学报》2002,19(3):17-19
本文通过对某产品变深槽加工关键技术的解决,阐述了变深槽靠模形板的设计原理。并对计算公式的推导及计算方法做了详细介绍,为以后类似零件的加工提供可借鉴的理论依据。 相似文献
12.
13.
14.
Tomasz Goetzendorf-Grabowski Dawid Mieszalski Ewa Marcinkiewicz 《Progress in Aerospace Sciences》2011,47(8):636-646
The SDSA (Simulation and Dynamic Stability Analysis) application is presented as a tool for analysing the dynamic characteristics of the aircraft just in the conceptual design stage. SDSA is part of the CEASIOM (Computerized Environment for Aircraft Synthesis and Integrated Optimization Methods) software environment which was developed within the SimSAC (Simulating Aircraft Stability And Control Characteristics for Use in Conceptual Design) project, funded by the European Commission 6th Framework Program. SDSA can also be used as stand alone software, and integrated with other design and optimisation systems using software wrappers. This paper focuses on the main functionalities of SDSA and presents both computational and free flight experimental results to compare and validate the presented software. Two aircraft are considered, the EADS Ranger 2000 and the Warsaw University designed PW-6 glider. For the two cases considered here the SDSA software is shown to be an excellent tool for predicting dynamic characteristics of an aircraft. 相似文献
15.
16.
根据刀具监控系统数据采集量大,计算量繁重以及对实时性要求高的特点,采用单片机和DSP并行处理的双CPU处理方案对系统进行设计,即该系统由并行运行的两个子系统构成:基于单片机80C196KC的信号采集及控制功能子系统负责反映刀具状态的各路信号的采集和各种控制功能;基于DSP TMS320C32为核心的信号处理子系统负责信号处理和刀具状态值的估计。此方案充分利用了DSP运算能力强和单片机控制能力强的优点,实现了系统的快速运算和实时控制功能。 相似文献
17.
The San Antonio Air Logistics Center (SA-ALC) Automatic Test Systems Division's Advanced Diagnostics and Technology Insertion Center (ADTIC) is exploring the addition of a non-intrusive diagnostics capability to existing Automatic Test Systems (ATS) utilizing various sensor technologies. The diagnostic techniques under development are expected to allow for more efficient fault detection and isolation than traditional ATS. This paper summarizes findings to date and discusses the integration of these technologies should they prove viable 相似文献
18.
The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming. 相似文献