新型刚玉砂轮磨削GH4169镍基高温合金的性能评价研究

镍基高温合金是航空发动机部件的常用材料,其磨削加工存在工具损耗严重、寿命短等难题.针对3种新研制的刚玉砂轮(分别为粒度60#的微晶和单晶混合磨料砂轮、粒度60#的单晶刚玉砂轮,以及粒度70#的单晶刚玉砂轮),开展了GH4169镍基高温合金材料的磨削试验,从磨削力、磨削温度、砂轮磨损以及表面粗糙度等方面对3种砂轮的磨削性...     

磁流变弹性体砂轮抛光镍基高温合金表面完整性研究

为了改善磨削后镍基高温合金GH4169的表面完整性,本文采用磁流变弹性体砂轮对镍基高温合金GH4169进行抛光试验研究。首先,通过模压成型的方法制备了磁流变弹性体砂轮,并对其表面微观形貌及不同磁场强度下的硬度进行了表征。其次将制备出的磁流变弹性体砂轮用于对镍基高温合金GH4169的抛光工艺试验中,并讨论抛光工艺参数中磁场强度对镍基高温合金表面完整性的影响。试验结果表明：在一定的磁场强度范围内,零件抛光后的表面粗糙度和显微硬度随着磁场强度的增大而减小,同时增大磁场强度也有利于改善零件的表面形貌,减少砂轮的磨损量,降低零件磨削后的亚表面损伤层厚度。     

Electrochemical machining on blisk channels with a variable feed rate mode

Electrochemical machining (ECM) is an economical and effective method for blisk manufacturing and includes two steps: channel machining and profile machining. The allowance distribution after the channel machining will directly affect the profile machining. Therefore, to improve the uniformity of allowance distribution in the machining of channels, a method that incorporates a variable feed rate mode is developed. During the machining process, the feed rates are dynamically changed according to the needs of the side gap at the different feed depths. As a result, the side gaps at the different feed depths vary, contributing to a decrease in the allowance difference. In this study, the dissolution processes of a blisk channel are simulated using different feed rates, and prediction profiles are obtained. Based on the prediction profiles, the relationship among the feed rate, feed depth, and side gap is established. Then, the feed rates at different feed depths are adjusted according to the relationship. In addition, contrast experiments are conducted. Compared with blisk channel ECM using a constant feed rate of 1 mm/min, using the variable feed rate decreases the allowance differences in the convex and concave parts by 62.2 % and 67.4 %, respectively. This indicates that using the variable feed rate in the ECM process for a blisk channel is feasible and efficient.     

阴极调速法测定电解加工ηω-i曲线特性的试验研究及其应用

镍基高温合金GH4169是航空发动机叶片的常用材料。为了精确获取GH4169的ηω-i曲线特性,采用调节阴极进给速度的新方法,实时控制加工间隙,使加工过程迅速过渡到平衡状态。利用阴极调速法开展了电解加工试验,经过计算得出ηω-i曲线。结果表明:当电流密度i小于6A/cm2时,ηω值趋向于0;当i大于50A/cm2时,ηω保持在1.28mm3/(A.min)不变。针对某航空发动机叶片,基于阴极调速法和恒速法测定的ηω-i曲线特性,分别设计了工具阴极,并开展了对比工艺试验研究。研究表明:根据阴极调速法测得ηω-i曲线特性设计的阴极,加工出叶片的复制精度明显提高,叶片精度整体提高0.03mm,证明该方法测定ηω-i曲线特性更加准确。     

Experimental investigation of rotary sinking electrochemical discharge milling with high-conductivity salt solution and non-pulsed direct current

Electrochemical milling is a modified technique of traditional electrochemical machining (ECM) that can be used to manufacture some helicopter transmission system parts. The use of rotary tools and an inner-jet electrolyte supply pattern can greatly improve the material removal rate (MRR) in a single pass. However, the feed speed is generally limited to minimize the tool wear. To increase the MRR, electrical discharge machining (EDM) is introduced into the electrochemical milling process. The tool rotation is employed to interrupt the discharge and the high-conductivity salt solution and non-pulsed direct current power supply are also adopted to increase ECM, eventually, a new machining method is proposed, which can be called rotary sinking electrochemical discharge milling (RSECD milling). The mechanism of it is explored in this study by analyzing the machined current, MRR, surface morphology, and tool wear at different applied voltages and feed speeds. Besides, the RSECD milling using the tool with a larger diameter is also conducted to further verify the effectiveness. In particular, the MRR can be increased by 742.5% when using the tool with a diameter of 20 mm at the applied voltage of 20 V.     

Grain erosion wear properties and grinding performance of porous aggregated cubic boron nitride abrasive wheels

Cubic boron nitride (cBN) superabrasive grinding wheels exhibit unique advantages in the grinding of difficult-to-cut materials with high strength and toughness, such as titanium alloys and superalloys. However, grinding with multilayered metallic cBN superabrasive wheels faces problems in terms of grain wear resistance, the chip storage capability of the working layers and the stability and controllability of the dressing process. Therefore, in this work, novel metallic cBN superabrasive wheels with aggregated cBN (AcBN) grains and open pore structures were fabricated to improve machining efficiency and surface quality. Prior to the grinding trials, the air-borne abrasive blasting process was conducted and the abrasive blasting parameters were optimized in view of wear properties of cBN grains and metallic matrix materials. Subsequently, the comparative experiments were performed and then the variations in grinding force and force ratio, grinding temperature, tool wear morphology and ground surface quality of the multilayered AcBN grinding wheels were investigated during machining Ti–6Al–4V alloys. In consideration of the variations of grain erosion wear volume and material removal rate per unit of pure metallic matrix materials as the abrasive blasting parameters changes, the optimal abrasive blasting parameters were identified as the SiC abrasive mesh size of 60# and the abrasive blasting distance and time of 60 mm and 15 s, respectively. The as-developed AcBN grains exhibited better fracture toughness and impact resistance than monocrystalline cBN (McBN) grains because of the existence of metal-bonded materials amongst multiple cBN particles that decreased crack propagation inside whole grains. The metallic porous AcBN wheels had lower grinding forces and temperature and better ground surface quality than vitrified McBN wheels due to the constant layer-by-layer exposure of cBN particles in the working layer of AcBN wheels.     

GH4169DA磨削表面变质层软化机理

为了深入研究高温合金GH4169DA磨削表面变质层软化机理,分别采用光学显微镜、显微维氏硬度计和透射电子显微镜（TEM）分析了其微观组织、显微硬度和γ"相密度。试验结果表明：GH4169DA磨削表面及亚表面发生了明显软化和局部塑性变形。在试验参数范围内,软化深度约为30~100 μm,而变形层的深度只有约4 μm。从基体到磨削表面,γ"相密度由约2.27×10³个/μm²逐渐降低,至距磨削表面约2.2 μm以内γ"相完全消失。该变化规律与显微硬度变化规律一致,最大影响深度也基本相同。分析指出,GH4169DA磨削表面软化的根本原因是在磨削过程中热的作用下,主要强化相γ"密度降低,强化效果减弱。     

GH4169合金直接时效锻造过程的数值模拟

直接时效（DA）锻造工艺已成为生产GH4169合金涡轮盘锻件的基本方法之一。但实施DA锻造工艺时,锻造过程的各个环节要求严格控制,而且要有足够吨位的设备。参照在压力机上实施DA工艺的终锻过程,用有限元变形-传热耦合分析方法对直径520mm和高度190mm的GH4169合金坯料在不同情况下的镦粗过程进行了数值模拟。大量计算结果表明,在压力机上实施DA锻造工艺时,为了获得优质GH4169合金涡轮盘锻件,应合理确定压力机滑块速度,尽可能改善润滑情况及适当提高模具预热温度。对于GH4169合金涡轮盘锻件,采用等温DA锻造工艺可能是最佳的选择。研究结果对于在国内的生产条件下实施GH4169合金DA锻造工艺具有指导作用。     

考虑静水压力和LODE 角的塑性模型 在GH4169 合金上的应用

针对典型盘用镍基高温合金GH4169,采用Bai-Wierzbizki(B-W)塑性理论对其塑性变形行为进行建模和应用评估。B-W塑性理论假设金属材料塑性变形仍服从von Mises屈服准则,但屈服函数考虑了静水压力和LODE角(偏应力第3不变量)对塑性行为的影响。采用Abaqus/Explicit商业有限元软件编制了该塑性模型的用户材料子程序,设计开展了GH4169合金的光滑、缺口圆棒和缺口平板拉伸试验,基于有限元分析和优化方法确定了B-W模型相关材料参数,对GH4169合金光滑和缺口拉伸响应曲线进行有限元预测,并与试验结果进行对比分析。结果表明:B-W模型预测的GH4169合金缺口圆棒和平板拉伸响应曲线与试验结果非常吻合,而基于传统von Mises塑性模型预测的GH4169合金缺口拉伸响应曲线均明显高于试验曲线。     

SHPB实验考虑绝热变形和端面摩擦的修正方法

采用高温分离式霍普金森压杆(SHPB)实验技术对GH4169高温合金进行测试,获得了材料在高应变率下的温度敏感性,并拟合了Johnson-Cook本构模型的参数。结合数值计算方法对压缩实验中试件内部的应力、应变以及温度的分布建立了一个半经验的数学模型并提出了一种新的参数修正方法,将端面摩擦效应、绝热变形升温效应与SHPB实验结果进行解耦。实验结果表明:温度越高,GH4169高温合金的屈服强度以及流动应力越小。并且在SHPB实验中GH4169高温合金存在明显的绝热变形升温效应和端面摩擦效应,导致实验结果并不能真实反映材料的硬化特性。通过对原始Johnson-Cook本构方程的硬化项乘以1.2的修正系数,发现修正后的本构参数准确反映了材料在高应变率下的应力应变特性。      

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

GH4169磨削表面粗糙度影响参数的敏感性研究

通过GH4169高温合金平面切入磨削实验,建立了表面粗糙度的经验公式,分析了表面粗糙度对磨削参数的灵敏度,获得了磨削参数稳定域和非稳定域。结合正交试验法中的极差分析方法获得了不同磨削参数对表面粗糙度的影响曲线,进行了磨削参数区间的优选。研究结果表明:表面粗糙度对磨削深度的变化最为敏感,对工件速度的变化敏感次之,对砂轮速度的变化最不敏感;磨削深度优选范围为0.01～0.015mm,工件速度优选范围为10～15m/min,砂轮速度优选范围为20～30m/s,可控制表面粗糙度在0.7μm以内。为高温合金材料磨削表面粗糙度控制提供理论方法和试验依据。     

GH4169高温合金高应变率本构关系试验研究

 基于高应变率下GH4169高温合金的本构关系是采用有限元法对GH4169高温合金进行切削加工数值分析研究的基础。本文针对GH4169高温合金,通过试验对其在温度为室温至1 000 ℃、应变率为2 000～10 000 s^-1的范围内的本构关系进行了研究。研究发现高应变率下GH4169高温合金的流动应力与塑性应变关系接近线性关系,同时温度影响着高应变率下应变率对本构关系的影响程度及方式。根据GH4169合金流动应力曲线的特点,对Johnson-Cook本构模型进行修正。基于试验结果,通过数据拟合确定了对应高应变率GH4169高温合金的材料常数,建立了描述GH4169高温合金高应变率下的本构模型,为切削加工有限元数值分析提供了理论基础,并为相关类似研究提供了思路。     

GH4169合金抗盐雾-热暴露循环腐蚀性能试验研究

通过盐雾-热暴露循环试验研究了GH4169合金的抗腐蚀性能。常温盐雾腐蚀试验按照GJB150.11-1986的要求进行,热暴露试验温度分别选择400、450、500、550、600和650℃,并将550和650℃下的试验结果与同温度下的高温氧化试验结果进行了对比分析。通过形貌观察、质量变化的比较、元素成分的测定等一系列宏观、微观分析,探究了GH4169合金的腐蚀机理。研究结果表明：GH4169合金在上述热暴露温度下均发生了腐蚀,但程度有所差异,呈现出随热暴露温度的升高,腐蚀加剧的趋势。     

高纯钨磨削加工试验研究

为探究适用于高纯钨磨削加工的砂轮,使用80~#绿碳化硅砂轮和金刚石砂轮开展磨削对比试验,从工件表面粗糙度角度评价上述两种砂料对高纯钨磨削加工表面的影响。试验结果表明,绿碳化硅砂轮对应的工件得到了更理想的表面粗糙度。使用绿碳化硅砂轮开展工艺试验,分析在不同磨削参数下加工表面粗糙度的变化趋势,以此为依据对高纯钨磨削加工工艺参数进行评价与优化。综合考虑加工表面粗糙度以及加工效率,得出适合于钨磨削加工的参数为砂轮线速度v_s=23m/s、磨削深度a_p=8μm、工作台进给速度v_w=10m/min,该参数下得到的表面粗糙度均值为0.336μm。     

叶片型面精密振动电解加工工艺研究

采用电解加工工艺对叶片型面进行加工,可以有效提高发动机叶片加工效率,降低生产成本。针对GH4169G合金叶片型面,开展了精密振动电解加工试验研究。结果表明:高频脉冲电流和阴极机械振动具有改善极间流场特性、降低阳极钝化和阴极的产物吸附的作用,可以大幅改善加工效果;采用参数组加工电压15V、阴极振动频率25Hz、开通角度Ra 150°~195°、脉冲频率3000Hz时,获得最优的型面加工质量,型面轮廓度为-0.012~+0.013mm,表面粗糙度值为0.51μm,证明精密振动电解加工工艺满足叶片型面的加工要求。     

Experimental research on electrochemical machining of titanium alloy Ti60 for a blisk

Ti60(Ti–5.6Al–4.8Sn–2Zr–1Mo–0.35Si–0.7Nd) is a high-temperature titanium alloy that is now used for important components of aircraft engines. Electrochemical machining(ECM) is a promising technique that has several advantages, such as a high machining rate, and can be used on a wide range of difficult-to-process materials. In this paper, orthogonal experiments are conducted to investigate ECM of Ti60, with the aim of determining the influences of some electrochemical process parameters on the surface roughness. The most important parameter is found to be the frequency of the pulsed power supply. It is found that using suitably optimized parameters for ECM can greatly decrease the surface roughness of a workpiece. A surface roughness of approximately 0.912 lm can be obtained with the following optimal parameters: Na Cl electrolyte concentration 13wt%, voltage20 V, pulse frequency 0.4 k Hz, duty cycle 0.3, temperature 23 °C, and anode feed rate 0.5 mm/min.Furthermore, blisk blades have been successfully processed using these optimized parameters.     

确定总应变寿命方程参数的一种方法

为了使总应变寿命方程能够在较大寿命范围内具有理想的预测精度且其参数物理意义明确,基于总应变寿命方程中疲劳强度系数与疲劳延性系数的物理意义,建立了总应变寿命方程参数与单调拉伸强度极限和断面收缩率之间的关系,并结合TC4,GH4169及GH901合金的单调拉伸及疲劳试验数据,对其各自的总应变寿命方程参数进行了拟合,进而开展了疲劳寿命预测.结果表明:采用该方法确定的总应变寿命方程参数具有明确的物理意义,且对TC4,GH4169及GH901合金的疲劳寿命预测结果较为理想,其分散带基本在2倍以内.      

Influences of milling and grinding on machined surface roughness and fatigue behavior of GH4169 superalloy workpieces

Surface topography of superalloy GH4169 workpieces machined by milling and grinding is different significantly. Meanwhile, surface roughness, as one of the main indicators of machined surface integrity, has a great influence on the fatigue behavior of workpieces. Based on analyzing the formation mechanism and characteristics of surface roughness utilizing different machining processes and parameters, the machined surface roughness curve can be decoupled into two parts utilizing frequency spectrum analysis, which are kinematic surface roughness curve and stochastic surface roughness curve. The kinematic surface roughness curve is influenced by machining process,parameters, geometry of the cutting tool or wheel, the maximum height of which is expressed as R'_z.By subtracting the kinematic part from the measurement curve, the stochastic surface roughness curve and its maximum height R'_zcan be obtained, which is influenced by the defects of cutting tool edge or abrasive grains, built-up edges(BUE), cracks, high frequency vibration and so on. On the other hand, the results of decoupling analysis of surface roughness curves indicate that Raand Rz values of milling GH4169 are 2–5 times and 1–3 times as high as those of grinding, while R'_zvalue of milling is 13.85%–37.7% as high as that of grinding. According to the results of fatigue life tests of specimens machined by milling and grinding, it can be concluded that fatigue behavior of GH4169 decreases with the increase of R'_zmonotonically, even utilizing different machining processes.     

高效砂轮的在线检测

硬质氮化硼磨料在很多加工场合可经济地代替常用的金刚砂，碳化硅等磨料，在加工过程中可显著提高生产率。但如何高效获得周转和平面理想的磨削结果，本文叙述的测量砂轮径跳的方法可达到其目的。